User Manual

ManualsBrandsGeophysical Survey Systems ManualsElectronicsStructureScan MiniXT with PalmXT Accessory 62300XT

Table Of Contents

Limited Warranty, Limitations Of Liability And Restrictions
- Regulatory Information
- Notice
- Survey Wheels
Garantie limitée, limites de responsabilité et restrictions
- Informations réglementaires
- Avis
- Roues codeuses – Odomètres
FCC Notice (for U.S. Customers):
- Coordination Requirements
(a) UWB imaging systems require coordination through the FCC before the equipment may be used. The operator shall comply with any constraints on equipment usage resulting from this coordination.
- For U.S. Customers
- Ground Penetrating Radar Coordination Notice And Equipment Registration
  - Fax this form to the FCC at: 202-418-1944
Or
Frequency Coordination Branch, OET
ATTN: UWB Coordination
Canadian Requirements for RSS-220
Canadian Requirements of RSS-220 for Ground Antennas
Canadian Requirements of RSS-220 for Hand-held Antennas
Canadian Requirements of RSS-220 for Search and Rescue Antennas
Table of Contents
- Section 1: Introduction 1
- StructureScan™ Mini XT 2
- Section 2: Getting Started 3
- Section 3: Using ScanEZ Mode 5
- Section 4: Using the Scan3D App 10
- Section 5: Using the ScanMax App 14
- Section 6: Calibrating for Depth in the ScanMax App 20
- Section 7: Using the DualScan App 23
- Section 8: File Management 26
- Setting up Your Laptop/PC and Data Transfer 27
- Launching and Navigating the Software 28
- Viewing and Processing the Data 30
- Processing the Data 32
- Ribbon Options 34
- Home Ribbon Options 34
- 3D Volume Options Ribbon 40
Chapter 1: Using the StructureScan Mini XT
Section 1: Introduction
- What Comes in the Box
- About this Manual
StructureScan™ Mini XT
- Front/Top View
- Back View
Section 2: Getting Started
- The Main Menu Screen
- First Time Setup
  - Setting UI App Mode
Section 3: Using ScanEZ Mode
- Configuring the Mini XT
- Understanding the Mini XT Screen
- Collecting Data and Marking Targets
- Playing Back 2D ScanEZ Data
Section 4: Using the Scan3D App
- Setting up Collection Parameters
- Collecting a Grid
- Recalling a Grid for Review
- Analyzing 3D Data
  - Slicing
  - Refining the Image
Section 5: Using the ScanMax App
- Setting up Collection Parameters
- Collecting Data
- Working with LineTrac
Section 6: Calibrating for Depth in the ScanMax App
- Using “Set Depth”
- Using “Set Dielectric”
- Using “Auto Depth”
Section 7: Using the DualScan App
- Setting Up for Data Collection and Choosing a Base File
- Collecting Data
- Playing Back DualScan Data
Section 8: File Management
Chapter 2: Using RADAN for StructureScan Mini
Setting up Your Laptop/PC and Data Transfer
- Transferring the Files
Launching and Navigating the Software
- Launching the Software
- Navigating Through the Main Screen
Viewing and Processing the Data
- Preparing the Software
- Opening a File
Processing the Data
- Initial Process (automatically done by the software)
Ribbon Options
Home Ribbon Options
- File
- Processing Options
  - Focus
  - Background Removal
- Data Windows
- Other Windows
- Interactive 2D
- Display Options
- Export 2D
- Clipboard
- Print
- Help
  - Mouse Functions
3D Volume Options Ribbon
- X-Slice, Y-Slice, Z-Slice
- View Options
- Export
Appendix A: The Dielectric Constant
Appendix B: Data Interpretation and Examples of Common Features
- Welded Wire Mesh
- Potential Void under Slab
- Rebar
- Empty PVC Conduit
- Cinder Block/CMU
Appendix C: Technical Specifications
Appendix D: Accessories
- Extension Pole with Six-Button Remote
- Extension Pole Transit Case
- LineTrac XT
Appendix E: Labeling
- FCC ID and Canadian ICES-003
- Laser Warnings

Geophysical Survey Systems, Inc. StructureScan™ Mini XT

Manual

MN 70-813 Rev C

Table of Contents

Chapter 1: Using the StructureScan Mini XT .........................................................................1

Section 1: Introduction ....................................................................................................... 1

StructureScan™ Mini XT ...................................................................................................... 2

Section 2: Getting Started.................................................................................................. 3

Section 3: Using ScanEZ Mode ......................................................................................... 5

Section 4: Using the Scan3D App ................................................................................. 10

Section 5: Using the ScanMax App .............................................................................. 14

Section 6: Calibrating for Depth in the ScanMax App ........................................... 20

Section 7: Using the DualScan App ............................................................................. 23

Section 8: File Management .......................................................................................... 26

Chapter 2: Using RADAN for StructureScan Mini ............................................................. 27

Setting up Your Laptop/PC and Data Transfer ........................................................ 27

Launching and Navigating the Software .................................................................. 28

Viewing and Processing the Data ................................................................................ 30

Processing the Data .......................................................................................................... 32

Ribbon Options .................................................................................................................. 34

Home Ribbon Options ..................................................................................................... 34

3D Volume Options Ribbon ........................................................................................... 40

Appendix A: The Dielectric Constant .................................................................................... 41

Appendix B: Data Interpretation and Examples of Common Features ................... 43

Appendix C: Technical Specifications ................................................................................... 47

Appendix D: Accessories ........................................................................................................... 49

Appendix E: Labeling .................................................................................................................. 52