User Manual
Table Of Contents
- Limited Warranty, Limitations Of Liability And Restrictions
- Garantie limitée, limites de responsabilité et restrictions
- FCC Notice (for U.S. Customers):
- (a) UWB imaging systems require coordination through the FCC before the equipment may be used. The operator shall comply with any constraints on equipment usage resulting from this coordination.
- Or
- Frequency Coordination Branch, OET
- ATTN: UWB Coordination
- Canadian Requirements for RSS-220
- Canadian Requirements of RSS-220 for Ground Antennas
- Canadian Requirements of RSS-220 for Hand-held Antennas
- Canadian Requirements of RSS-220 for Search and Rescue Antennas
- Table of Contents
- Section 1: Introduction 1
- StructureScan™ Mini XT 2
- Section 2: Getting Started 3
- Section 3: Using ScanEZ Mode 5
- Section 4: Using the Scan3D App 10
- Section 5: Using the ScanMax App 14
- Section 6: Calibrating for Depth in the ScanMax App 20
- Section 7: Using the DualScan App 23
- Section 8: File Management 26
- Setting up Your Laptop/PC and Data Transfer 27
- Launching and Navigating the Software 28
- Viewing and Processing the Data 30
- Processing the Data 32
- Ribbon Options 34
- Home Ribbon Options 34
- 3D Volume Options Ribbon 40
- Chapter 1: Using the StructureScan Mini XT
- Section 1: Introduction
- StructureScan™ Mini XT
- Section 2: Getting Started
- Section 3: Using ScanEZ Mode
- Section 4: Using the Scan3D App
- Section 5: Using the ScanMax App
- Section 6: Calibrating for Depth in the ScanMax App
- Section 7: Using the DualScan App
- Section 8: File Management
- Chapter 2: Using RADAN for StructureScan Mini
- Setting up Your Laptop/PC and Data Transfer
- Launching and Navigating the Software
- Viewing and Processing the Data
- Processing the Data
- Ribbon Options
- Home Ribbon Options
- 3D Volume Options Ribbon
- Appendix A: The Dielectric Constant
- Appendix B: Data Interpretation and Examples of Common Features
- Appendix C: Technical Specifications
- Appendix D: Accessories
- Appendix E: Labeling
Geophysical Survey Systems, Inc. StructureScan™ Mini XT
Manual
MN 70-813 Rev C 4
First Time Setup
Note: The Mini XT incorporates a touch screen. You can use the handle keypad or touchscreen to access
most of the menu items.
Setting UI App Mode
The StructureScan Mini XT apps are divided into two categories for ease of use. These categories are
referred to as UI Modes. The UI Modes are accessible from the menu carousel, secondary menu:
• Simple Mode: ScanEZ
• Standard Mode: ScanEZ, ScanMax, Scan3D
• Advanced Mode: ScanEZ, ScanMax, Scan3D, DualScan
For first time setup, make sure that the Mini XT is in Standard UI mode.
1 Set Language: Make sure that the Mini XT is in ScanMax App. Click the Down arrow to highlight
the menu carousel and then the Left/Right arrows to choose Select Language. Click the middle
keypad button or press the softkey on the carousel to select. Choose your desired language. This may
cause the Mini XT to restart.
2 Set Units: In the ScanMax App, choose Units from the menu carousel. Click the middle handle
keypad button to press the softkey to toggle between English (Imperial) and Metric units.
3 Calibrate Antenna: In the ScanMax App, select Calibrate Antenna from the menu carousel. Follow
the onscreen instructions. Calibrating will set appropriate gain levels.
4 Set Date/Time: In the ScanMax App, choose the secondary menu softkey: Click the middle
handle button or push the softkey to toggle to the ScanMax secondary menu carousel.
Follow the onscreen instructions to set the appropriate date and time.
The choices you have made here will carry over to the ScanEZ and the Scan3D Collection Apps.
Secondary Menu