Installation & Assembly

`
IMPORTANT: Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Dimmable with C-L (CFL & LED)type and
Incandescent/Halogen type dimmers
INSTALLATION INSTRUCTIONS FOR P5219-077-L
For LED Wall Mount Fixture
WARNING ! S HUT PO W E R OFF AT FUSE O R CIRCUIT BRE AKER.
AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T AU N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R .
PREPARATION
1. Shut off power at the fuse box or circuit breaker box. If
necessary remove the old fixture and mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on
a clear area. Take care not to lose any small parts necessary
for installation.
3. Position mounting plate (B) on the wall, and mark the
location of the two drywall anchors (A). Pre-drill the holes for
the drywall anchors (A). Insert the drywall anchors (A) into
the wall.
4. Attach the mounting plate (B) to the outlet box with mounting
screws (E) (Size: 8-32*1/2’’L) and wood screws (D). The side
of the mounting plate marked “GND” must face out.
5. Thread the two screws (C) into the mounting plate spaced
the same distance apart as the mounting holes of fixture (F).
CONNECTING THE WIRES
6. Connect the electrical wires as shown in Fig.2, making sure
that all wire nuts are secured. If your outlet has a ground wire
(green or bare copper), connect the fixture's ground Wire to
it. Otherwise, connect the fixture's ground wire directly to the
Mounting plate (B) using the green screw (P) provided. Tuck
the wire connections neatly into the junction box.
FINISHING THE INSTALLATION (FIG. 1)
7. Align fixture (F) to screws (C) and secure with cap nuts (O).
8. Align screw (I), steel gasket (J) and plastic gasket (K) to the
glass (N) and secure into hook (L).
9. Align hook (L) with glass (N) to fixture (F) and secure with
screws (M).
CAUTION /ATTENTION: When handling the fixture, do not
apply pressure to the LEDs. Hold the fixture by the base or
back plate (F) only.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps
for more details (Fig 3.)
Warning: Turn off power at the circuit breaker before
replacing LED module or LED driver.
a. Remove screws (M) to remove glass (N) from the fixture
(F).
b. Remove ball nuts (O) to remove the fixture (F) from the
mounting plate (B).
c. Remove the wire nuts located inside the fixture front plate
and remove screw (T) on fastener (U) to disconnect the
LED module.
d. Remove screws (Q) to remove the bracket (P) from the
fixture (F).
e. Remove screws (S) and carefully remove the LED module
(R) from bracket (P).
f. Reverse steps a-c for installing the new LED module.
g. Note: The LED module should be provided by a specified
supplier.
h. For better heat dissipation the LED module should be
applied with thermal grease when re-lamping.
Fig.1
Set:
Green screw
Mounting box screw(2)
JUNCTION
BOX
O
Brand: Lutron
Ordering Information ■Boxed ●Clamshell
Model number
Product name
Control type
Maximum capacity
■DVCL-153P-
Diva-C-L
Single-pole/3-way
dimmer-
150 W CFL/LED or 600
W Incandescent/
Halogen 120 V
●DVCL-153PH-
■DVSCCL-153P-
Diva C-L Satin Colors
■CTCL-153P-
Skylark Contour C-L
●CTCL-153PH-
■AYCL-153P-
Ariadni C-L
●AYCL153PH-
●TTCL-100H-
Credenza C-L
Single-pole lamp
dimmer
100W CFL/LED or 250W
Incandescent/ Halogen
120v
Fig 3
Fig.2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare
Copper(G
round)