Installation & Assembly

ManualsBrandsGeorge Kovacs by Minka ManualsLightingLED Outdoor Flush Mount

A B

INSTALLATION INSTRUCTIONS

Item# P1237

READ AND SAVE THESE INSTRUCTIONS

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

ASSEMBLING THE FIXTURE (Fig.1)

1 Shut off power at the fuse box or circuit breaker. If necessary,

remove the old fixture including the mounting hardware.

2 Carefully remove the fixture from the carton and check that all

parts are included as show in Figure 1.

3 Loosen screws (C) and separate mounting plate (A) from

fixture (D).

4 Attach mounting plate (A) to the junction box with junction box

screws (B) (size: 8-32*1/2”L). The side of the mounting plate

marked “GND” must be face out.

CONNECTION THE WIRES (Fig. 2)

5 Connect the electrical wires as shown in Fig.2, making sure

that all wire nuts are secured. If your outlet has a ground wire

(green or bare copper), connect the fixture's ground Wire to it.

Otherwise, connect the fixture's ground wire directly to the

circular strap using the green screw provided. Tuck the wire

connections neatly into the junction box.

FINISHING THE INSTALLATION (Fig. 1)

6 Align fixture (D) and clip (E) onto mounting plate (A) and

secure with screws (C).

7 To prevent moisture from entering the outlet box and causing a

short circuit, use clear caulking (i.e. Indoor/Outdoor silicone

sealant) to outline the outside of fixture back plate where it

meets the wall leaving a space at bottom to allow moisture a

means to escape (Fig.3).

Your installation is now complete. Return power to the junction box

and test the fixture.

CAUTION /ATTENTION:

When handling the fixture, do not apply

pressure to the LED. Hold the fixture by the base or back plate (G)

only.

Replacing LED module (Fig. 4)

The LED module can be replaced by a qualified electrician without

cutting of wire and without damage to any decorative element to

which the fixture is attached. See installation steps for more details

(Fig. 4)

Warning: Turn off power at the circuit breaker before

replacing LED module.

a. To remove the fixture from the wall, loosen screws (C) and

remove fixture (D) and clip (E) from mounting plate (A). Remove

the wire connectors and place the fixture on a clear flat surface.

(Fig. 1)

b. Loosen screws (Q) and remove rubber washers (R) to separate

glass holder (P) and glass shade (O) from back plate (G).

c. Loosen screws (N), remove rubber washers (M) and hex nuts

(F) to separate glass panel (L) from LED housing (I). (Fig. 4)

d. Loosen screws (K) and hex nuts (H) and carefully remove LED

module (J) from LED housing (I).

e. Reverse steps a-d for installing the new LED module.

Note: The LED module should be provided by a specifie

d supplier.

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Green or

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Set

021

120

- Mounting Plate

- Ground Screw

Mounting

Screw

IMPORTANT:

Fixture should be installed by a qualified electrician

to ensure proper wiring and installation.

Dimmable with C-L (CFL & LED) type and Incandescent/Halogen type

dimmers

Summary of content (1 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Item# P1237 READ AND SAVE THESE INSTRUCTIONS W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR. ASSEMBLING THE FIXTURE (Fig.1) 1 2 3 4 Fig. 1 Shut off power at the fuse box or circuit breaker. If necessary, remove the old fixture including the mounting hardware. Carefully remove the fixture from the carton and check that all parts are included as show in Figure 1.