Installation Guide

ManualsBrandsGeorge Kovacs ManualsLightingLight Ray 150-Watt Equivalence Integrated LED Brushed Nickel Pendant

INSTALLATION INSTRUCTIONS

FOR P1783-084-L

FOR LED Pendant Light

WARNI NG! SH UT P OWE R O FF AT FUS E O R C IRC UIT BRE AKE R .

AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R

Page: 1/2

Fig. 2

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and

remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in

a clear area. Take care not to misplace any small parts

necessary for installation.

SUGGESTED INSTALLATION (Fig. 1)

3. Remove the three mounting screws (DD) from the side of

the canopy (A) and remove the mounting plate (BB).

4. Press the wire restraints (B) onto the canopy (A) to adjust

the six cables (C) length.

5. Attach the mounting plate (BB) to the junction box. Place

marks on the ceiling where the support screw holes are

located. Remove the mounting plate (BB).

6. Drill pilot holes in the ceiling with a 1/4 in. drill bit. Push the

plastic anchors (FF) into the holes.

7. Secure the mounting plate (BB) to the outlet box (not

included) with the outlet box screws (CC). Tighten until snug.

Screw the wood screws (EE) into the plastic anchors(FF).

CONNECTING THE WIRES (Fig. 2)

8. At this point, connect the electrical wires as shown in figure.

2, making sure that all wire connectors are secured. If your

outlet has a ground wire (green or bare copper), connect the

fixture’s ground wire to it. Otherwise, connect the fixture’s

ground wire directly to the circular strap using the green

screw provided.

COMPLETING THE INSTALLATION (Fig. 1)

9. Attach the canopy (A) to the mounting plate (BB) and secure

it with the mounting screws (DD).

Your installation is now complete. Return power to the

junction box and test the fixture.

IMPORTANT: Fixture should be installed by a qualified electrician to

ensure proper wiring and installation.

Dimmable with ELV and/or LED compatible wall dimmer switches.

Fig.1

set#A-021-294

- Mounting plate

- Ground screw

- Mounting screws*2pcs

- Plastic anchor*3pcs

- Wood screws*3pcs

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR P1783-084-L FOR LED Pendant Light W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R PREPARING FOR INSTALLATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a clear area.
PAGE 2
Fig.3 Replacing LED module (Fig. 3) The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig.3.) a. Shut off power. Remove the three mounting screws (DD) from the side of the canopy (A). b. Disconnect the wire by removing wire nuts. Take the whole fixture down to the working table. c. Disconnect the wire of the driver by removing wire nuts.