Installation Manual

ManualsBrandsGeovision ManualsElectronicsElectromagnetic Lock 1200lb with LED

Table Of Contents

GV-ML1200 Electromagnetic Lock

GV-ML1200 Electromagnetic Lock

The GV-ML1200 is a surface mount electromagnetic lock featured with a built-in voltage

spike suppressor and a sensor. It can be applied for single-leaf or double-leaf doors.

Packing List

1. GV-ML1200 electromagnetic lock x 1

2. Magnet faceplate x 1

3. Inner hexagon wrench x 1

4. M8 (41mm) screw + black rubber

spacer x 1

5. Hat nut x 1

6. Galvanized steel rivet x 2

7. Black rubber spacer x 2

8. Aluminum shim x 2

9. #10 (5/8”) screw x 2

10. #10 (1.25”) screw x 9

11. M4 (7mm) flat-head screw x 2

12. M5 (8mm) flat-head screw x 2

13. Washer x 3

14. Aluminum tube x 1

15. Tamper-proof tube x 3

June 3, 2015

Summary of content (10 pages)

PAGE 1
GV-ML1200 Electromagnetic Lock The GV-ML1200 is a surface mount electromagnetic lock featured with a built-in voltage spike suppressor and a sensor. It can be applied for single-leaf or double-leaf doors. Packing List 1. GV-ML1200 electromagnetic lock x 1 2. Magnet faceplate x 1 3. Inner hexagon wrench x 1 4. M8 (41mm) screw + black rubber spacer x 1 5. Hat nut x 1 6. Galvanized steel rivet x 2 7. Black rubber spacer x 2 8. Aluminum shim x 2 9. #10 (5/8”) screw x 2 10. #10 (1.25”) screw x 9 11.
PAGE 2
Installation Before installing, add the thread lockers to all screws. Be sure to firmly tighten the screws. 1. Install the electromagnetic lock to the doorframe.
PAGE 3
2. Mounts the armature plate to the door. Typical Installation of the electromagnetic lock: Note: To make the armature plate adjust its proper position to the magnet automatically, do not fix the armature plate too tightly and make the rubber washer more flexible.
PAGE 4
Note: If the power switch is not wired between the DC source voltage and the magnet, it will take longer to de-energize the magnet simulating residual magnetism.
PAGE 5
Connecting to Power Unscrew the cover of electromagnetic lock, and connect the lock to the output interface of the GV-AS Controller and a power supply. Here we use GV-AS410 Controller as an example. 1. Power Terminal Block: Connects to a DC 12V / 24V power source. Connect the (+) point on the electromagnetic lock to COM on GV-AS410, connect the two (-) points of the electromagnetic lock and the external power supply together, and connect the (+) point on the external power supply to NC on GV-AS410. 2.
PAGE 6
Note: 1. It is required to connect an external power supply if the total power consumption of the output devices and readers connected to the GV-AS Controller exceeds 3A (for GVAS210 / 2110), 3.5A (for GV-AS410 / 4110) or 5A (for GV-AS810 / 8110). 6 GND 12V GND 12V GND 12V 2. You may use the power outputs on the GV-AS Controller when the total power consumption of the output devices and readers connected to the GV-AS Controller is under 3A (for GV-AS210 / 2110), 3.
PAGE 7
Connecting a Sensor to the GV-AS Controller There are two types of sensors for the electromagnetic lock: Door Closure Detection Sensor and Magnet Clasp Detection Sensor. The sensors will detect whether the door is closed tightly or not, and trigger a “Held Open” message on GV-ASManager when the door remains unlocked. To connect the sensors to the GV-AS Controller, follow the steps below. Here we use GV-AS410 Controller as an example. Note: Only one type of sensor could be applied at a time.
PAGE 8
Option 2: Magnet Clasp Detection Sensor To connect the Magnet Clasp Detection Sensor to the GV-AS410, connect one wire from NC of the electromagnetic lock’s circuit board to the Input of the GV-AS410, and connect the other wire from COM of the electromagnetic lock’s circuit board to the Ground of the GVAS410. Note: The two wires mentioned in Option 2 are not included in the package; the users must prepare them additionally. It is recommended to use wire No. 26 AWG (American Wire Gauge) or above.
PAGE 9
Setting the Web Interface of the GV-AS Controller Here we use GV-AS410 Controller as an example. 1. To configure the input setting of connected sensor: on the Web interface of the GV-AS410, select Advanced Setting, select Input Configuration, and set the input function to Door Contact. 2. To configure the output setting of the electromagnetic lock: on the Web interface of the GV-AS410, select Advanced Setting, select Output Configuration, and set the output function to Electric Lock.
PAGE 10
Specifications Voltage DC 12V / 24V Current 500mA at 12V / 250mA at 24V Holding Force 544.311 kg (1200 lb) Operating Temperature -20°C ~ 60°C (-4°F ~ 140°F) Dimensions (L x W x H) 266 x 73 x 40 mm (10.47” x 2.87” x 1.57”) Armature Plate Dimensions (L x W x H) 185 x 61 x 16 mm (7.28” x 2.40” x 0.62”) Weight 5 kg (11.02 lb) Certification CE, UL, ISO 9001, RoHS All specifications are subject to change without notice.