Installation Guide
Table Of Contents
- Contents
- Installation Overview
- Required Accessories
- Note for Installing Camera Outdoor
- Note for Adjusting Focus and Zoom
- Note for Supported Power Box Types
- Note for IP LPR Camera
- 1. Introduction
- 2. Installing the Vandal Proof IP Dome (Part I)
- 2.1 Assembling the Vandal Proof IP Dome with the dome housing
- 2.2 Straight Tube Box Mount
- 2.3 Straight Tube Mount
- 2.4 Wall Mount
- 2.5 L-Shaped Wall Mount
- 2.6 Wall Box Mount
- 2.7 Wall Pendant Mount
- 2.8 Convex Corner Mount with Pendant Tube
- 2.9 Convex Corner Mount with Wall Bracket
- 2.10 Convex Corner Box Mount
- 2.11 Concave Corner Mount with Pendant Tube
- 2.12 Concave Corner Mount with Wall Bracket
- 2.13 Pole Mount with Pendant Tube
- 2.14 Pole Mount with Wall Bracket
- 2.15 Pole Box Mount
- 2.16 Power Box Mount
- Note for Installing the Vandal Proof IP Dome
- 3. Installing the Vandal Proof IP Dome (Part II)
- 3.1 Straight Tube Box Mount
- 3.2 Straight Tube Mount
- 3.3 Wall Mount Bracket
- 3.4 L-Shaped Wall Mount
- 3.5 Wall Box Mount
- 3.6 Wall Pendant Mount
- 3.7 Convex Corner Mount with Pendant Tube
- 3.8 Convex Corner Mount with Wall Bracket
- 3.9 Convex Corner Box Mount
- 3.10 Concave Corner Mount with Pendant Tube
- 3.11 Concave Corner Mount with Wall Bracket
- 3.12 Pole Mount with Pendant Tube
- 3.13 Pole Mount with Wall Bracket
- 3.14 Pole Box Mount
- 3.15 Power Box Mount
- 3.16 In-Ceiling Mount
- 4. Installing the Fixed IP Dome
- 5. Installing the Fisheye Camera
- 6. Installing the GV-IP Speed Dome
- 6.1 Assembling Outdoor IP Speed Dome with Pendant Tube
- 6.2 In-Ceiling Mount6.2.1 GV-SD220
- 6.2.2 GV-SD220-S / GV-SD2300
- 6.3 Straight Tube Box Mount 6.3.1 GV-SD220-S / GV-SD2300
- 6.3.2 GV-SD2301 / GV-SD2411
- 6.4 Straight Tube Mount6.4.1 GV-SD220-S / GV-SD2300
- 6.4.2 GV-SD2301 / GV-SD2411
- 6.5 Convex Corner Mount
- 6.6 Convex Corner Box Mount
- 6.6.1 GV-SD220-S / GV-SD2300
- 6.6.2 GV-SD2301 / GV-SD2411
- 6.7 Concave Corner Mount
- 6.8 Pole Mount
- 6.9 Pole Box Mount
- 6.9.2 GV-SD2301 / GV-SD2411
- Note for Closing the Bullet Camera Cover
- 7. Installing the Bullet / Target Bullet / IP LPR Camera
- Note for Installing the Box Camera
- 8. Installing the Box Camera
- 9. Installing the Arctic Box / IP LPR Camera
- 10. Installing the Mini Fixed Dome
- 11. Installing the Mini Fixed Rugged Dome
- 12. Installing the Target (Mini) Fixed Dome
- 12.1 L-Shaped Wall Mount
- 12.2 Wall Box Mount
- 12.3 Wall Mount Bracket
- 12.4 Power Box Mount
- 12.5 GV-EFD2101 / EFD3101 In-Ceiling Mount
- 12.6 Assembling GV-EFD2101 / EFD3101 with Dome Housing
- 12.7 Wall Pendant Mount
- 12.8 Straight Tube Mount
- 12.9 Straight Tube Box Mount
- 12.10 Convex Corner Mount
- 12.11 Convex Corner Box Mount
- 12.12 Concave Corner Mount
- 12.13 Pole Mount
- 12.14 Pole Box Mount
- 13. Installing the Target Mini Fixed Rugged Dome
- 14. Installing the Target Vandal Proof IP Dome
- 14.1 L-Shaped Wall Mount
- 14.2 Wall Mount Bracket
- 14.3 In-Ceiling Mount
- 14.4 Assembling Dome Housing
- 14.5 Wall Pendant Mount
- 14.6 Straight Tube Mount
- 14.7 Straight Tube Box Mount
- 14.8 Convex Corner Mount with Pendant Tube
- 14.9 Convex Corner Mount with Wall Bracket
- 14.10 Convex Corner Box Mount
- 14.11 Concave Corner Mount with Pendant Tube
- 14.12 Concave Corner Mount with Wall Bracket
- 14.13 Pole Mount
- 14.14 Pole Box Mount
Installing the GV-IP Speed Dome
6
2. Assemble the tube (GV-Mount103, No. 3), the housing cap (GV-Mount103, No. 2), and
the mounting bracket (GV-Mount103, No. 1) by rotating the parts together.
3. Make sure the tubes are properly screwed. Tighten the screws using the supplied torx
wrench (GV-Mount103, No. 4).
4. Thread the network, power and other cables (including the cables connected through the
waterproof rubber) through the tube.
5. Connect the network, power and other cables to the camera. See 1.6 Connecting the
Camera, GV-IP Speed Dome User’s Manual on the software CD/DVD.
6. Rotate the camera onto the mounting cap, and secure the camera using the supplied No.
5 torx wrench (GV-Mount103, No. 4). For detailed installation procedures of the cameras,
see 6.1.2 GV-SD2301 / GV-SD2411.
7. Secure the assembled camera to the ceiling with 4 self-prepared screws.
243