Installation Guide
Table Of Contents
- Contents
- Installation Overview
- Required Accessories
- Note for Installing Camera Outdoor
- Note for Adjusting Focus and Zoom
- Note for Supported Power Box Types
- Note for IP LPR Camera
- 1. Introduction
- 2. Installing the Vandal Proof IP Dome (Part I)
- 2.1 Assembling the Vandal Proof IP Dome with the dome housing
- 2.2 Straight Tube Box Mount
- 2.3 Straight Tube Mount
- 2.4 Wall Mount
- 2.5 L-Shaped Wall Mount
- 2.6 Wall Box Mount
- 2.7 Wall Pendant Mount
- 2.8 Convex Corner Mount with Pendant Tube
- 2.9 Convex Corner Mount with Wall Bracket
- 2.10 Convex Corner Box Mount
- 2.11 Concave Corner Mount with Pendant Tube
- 2.12 Concave Corner Mount with Wall Bracket
- 2.13 Pole Mount with Pendant Tube
- 2.14 Pole Mount with Wall Bracket
- 2.15 Pole Box Mount
- 2.16 Power Box Mount
- Note for Installing the Vandal Proof IP Dome
- 3. Installing the Vandal Proof IP Dome (Part II)
- 3.1 Straight Tube Box Mount
- 3.2 Straight Tube Mount
- 3.3 Wall Mount Bracket
- 3.4 L-Shaped Wall Mount
- 3.5 Wall Box Mount
- 3.6 Wall Pendant Mount
- 3.7 Convex Corner Mount with Pendant Tube
- 3.8 Convex Corner Mount with Wall Bracket
- 3.9 Convex Corner Box Mount
- 3.10 Concave Corner Mount with Pendant Tube
- 3.11 Concave Corner Mount with Wall Bracket
- 3.12 Pole Mount with Pendant Tube
- 3.13 Pole Mount with Wall Bracket
- 3.14 Pole Box Mount
- 3.15 Power Box Mount
- 3.16 In-Ceiling Mount
- 4. Installing the Fixed IP Dome
- 5. Installing the Fisheye Camera
- 6. Installing the GV-IP Speed Dome
- 6.1 Assembling Outdoor IP Speed Dome with Pendant Tube
- 6.2 In-Ceiling Mount6.2.1 GV-SD220
- 6.2.2 GV-SD220-S / GV-SD2300
- 6.3 Straight Tube Box Mount 6.3.1 GV-SD220-S / GV-SD2300
- 6.3.2 GV-SD2301 / GV-SD2411
- 6.4 Straight Tube Mount6.4.1 GV-SD220-S / GV-SD2300
- 6.4.2 GV-SD2301 / GV-SD2411
- 6.5 Convex Corner Mount
- 6.6 Convex Corner Box Mount
- 6.6.1 GV-SD220-S / GV-SD2300
- 6.6.2 GV-SD2301 / GV-SD2411
- 6.7 Concave Corner Mount
- 6.8 Pole Mount
- 6.9 Pole Box Mount
- 6.9.2 GV-SD2301 / GV-SD2411
- Note for Closing the Bullet Camera Cover
- 7. Installing the Bullet / Target Bullet / IP LPR Camera
- Note for Installing the Box Camera
- 8. Installing the Box Camera
- 9. Installing the Arctic Box / IP LPR Camera
- 10. Installing the Mini Fixed Dome
- 11. Installing the Mini Fixed Rugged Dome
- 12. Installing the Target (Mini) Fixed Dome
- 12.1 L-Shaped Wall Mount
- 12.2 Wall Box Mount
- 12.3 Wall Mount Bracket
- 12.4 Power Box Mount
- 12.5 GV-EFD2101 / EFD3101 In-Ceiling Mount
- 12.6 Assembling GV-EFD2101 / EFD3101 with Dome Housing
- 12.7 Wall Pendant Mount
- 12.8 Straight Tube Mount
- 12.9 Straight Tube Box Mount
- 12.10 Convex Corner Mount
- 12.11 Convex Corner Box Mount
- 12.12 Concave Corner Mount
- 12.13 Pole Mount
- 12.14 Pole Box Mount
- 13. Installing the Target Mini Fixed Rugged Dome
- 14. Installing the Target Vandal Proof IP Dome
- 14.1 L-Shaped Wall Mount
- 14.2 Wall Mount Bracket
- 14.3 In-Ceiling Mount
- 14.4 Assembling Dome Housing
- 14.5 Wall Pendant Mount
- 14.6 Straight Tube Mount
- 14.7 Straight Tube Box Mount
- 14.8 Convex Corner Mount with Pendant Tube
- 14.9 Convex Corner Mount with Wall Bracket
- 14.10 Convex Corner Box Mount
- 14.11 Concave Corner Mount with Pendant Tube
- 14.12 Concave Corner Mount with Wall Bracket
- 14.13 Pole Mount
- 14.14 Pole Box Mount
3. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance
(approximately 2 mm) to hang the wall mount bracket later.
Wall
2 mm
Long
Screw
4. Unscrew the camera’s cover using the supplied torx wrench.
5. Unscrew the three screws as indicated below. A back plate can be separated from the
bottom.
6. Align and secure the back plate to the wall mount bracket with two M3 screws (GV-
Mount900, No. 4). Use the holes indicated with MDF.
338