Quick Start Guide GV-AS / EV Controller Thank you for purchasing GV-AS / EV Controller. This guide is designed to assist the new user in getting immediate results from the controllers. For advanced information on how to use the GVAS100 / 1010 / 110 / 1110 / 120 / 210 / 2110 / 2120 / 410 / 4110 / 810 / 8110 and GV-EV48, please refer to GV-AS / EV Controller User's Manual on Software CD / DVD.
© 2015 GeoVision, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of GeoVision. Every effort has been made to ensure that the information in this manual is accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein.
Contents Contents...........................................................................................................................i Important Note for Maintaining Power Supply.................................................................. ii GV-AS Controller Quick Start Guide............................................................................... 1 1. Basic Setup for GV-AS100 / 1010 / 110 / 1110 / 120................................................. 1 1.1 GV-AS100 / 1010 ................
Important Note for Maintaining Power Supply To make sure GV-AS / EV Controllers can function properly during a power outage, be sure to replace the internal battery on the controllers when needed. It is also recommended to install a backup battery for compatible GV-AS Controllers. Refer to the following sections in GV-AS Controller User Manual for instructions on how to install a backup battery: z GV-AS100 / 110 / 120 through GV-ASBox: See 9.1.4.F Connecting Backup Battery.
Built-in Battery (GV-AS1010 / 110 / 1110 / 120 / 210 / 410 / 810 & GV-EV48) When the controller runs out of battery, the local time on the controller will be reverted back to 1999/12/31. The controller time can be found on the Web interface of the controller on the Time Setting page and in the Access Monitor / Alarm Monitor / Event Monitor of GVASManager. When you see the controller year shown as 1999 or 2000, disconnect the controller from power and reconnect it to power.
GV-AS Controller Quick Start Guide This guide lists the basic steps required to set up a GV-AS Controller. For detailed instructions, refer to the section number listed below each step. 1. Basic Setup for GV-AS100 / 1010 / 110 / 1110 / 120 This section covers the basic settings required to start running GV-AS100 / 1010 / 110 / 1110 / 120. For more settings on GV-AS100 / 110 / 120, refer to 5. Optional Devices for GV-AS100 / 110 / 120.
1.1 GV-AS100 / 1010 Connect card readers (Optional) Connect AS100 / 1010 to a reader. 1.2.1 Connecting Card Readers Connect input devices Connect AS100 / 1010 to input devices (Ex: a push button to exit). 1.2.2 Connecting Input Devices Connect output devices Connect AS100 / 1010 to output devices (Ex: a door lock). GV-AS100 1.2.3 Connecting Output Devices Connect to PC Connect the controller to a computer through RS485 connection (AS100) or network connection (AS100 & AS1010). 1.2.
1.2 GV-AS110 / 1110 Connect card readers (Optional) Connect AS110 / 1110 to a reader.. 2.2.1 Connecting Card Readers Connect input devices Connect AS110 / 1110 to input devices (Ex: a push button to exit). 2.2.2 Connecting Input Devices GV-AS110 / 1110 Connect output devices Connect AS110 / 1110 to output devices (Ex: a door lock). 2.2.3 Connecting Output Devices Connect to PC Connect the controller to a computer through RS485 connection (AS110) or network connection (AS110 & AS1110). 2.2.
1.3 GV-AS120 Connect card readers (Optional) Connect AS120 to a reader through Wiegand interface. 3.2.1 Connecting a Wiegand Reader Connect input devices Connect AS120 to input devices (Ex: a push button to exit). 3.2.2 Connecting Input Devices Connect output devices GV-AS120 Connect AS120 to output devices (Ex: a door lock). 3.2.3 Connecting Output Devices RS485 Connection Connect to PC 3.2.4.A RS-485 Connection Connect AS120 to a computer through RS485 connection or network connection.
2. Physical Wiring for GV-AS210 / 2110 / 2120 / 410 / 4110 / 810 / 8110 and GV-EV48 2.1 GV-AS210 / 2110 / 2120 Wiegand Connect card readers Connect AS210 / 2110 / 2120 to readers through Wiegand or RS-485 interface. 4.2.1.A Wiegand Readers RS485 4.2.1.B RS-485 Readers Connect input devices Connect AS210 / 2110 / 2120 to input devices (Ex: a push button to exit). 4.2.2 Connecting Input Devices Connect output devices Connect AS210 / 2110 / 2120 to output devices (Ex: a door lock). 4.2.
2.2 GV-AS410 / 4110 / 810 / 8110 Wiegand Connect card readers Connect AS410 / 4110 / 810 / 8110 to readers through Wiegand or RS-485 interface. 5.2.1.A Wiegand Readers RS485 5.2.1.B RS-485 Readers Connect input devices Connect AS410 / 4110 / 810 / 8110 to input devices (Ex: a push button to exit). 5.2.2 Connecting Input Devices Connect output devices Connect AS410 / 4110 / 810 / 8110 to output devices (Ex: a door lock). 5.2.
2.3 GV-EV48 Connect card readers Connect EV48 to readers through RS-485 interface. 6.2.1 Connecting RS-485 Card Readers Connect output relay Connect EV48 output relays to the corresponding floor on the elevator control panel. 6.2.2 Connecting Output Relay GV-EV48 Connect Backup Battery (Optional) Connect EV48 to backup battery in case the main power supply fails. 6.2.3 Connecting Backup Battery Connect to Power Connect EV48 to power using the supplied 12V DC adaptor. 6.2.
3. Accessing the Web Interface of the GV-AS Controllers After connecting the required wires and cables for the following GV-AS Controllers, access the Web interface of the GV-AS Controller to define the devices connected: GV-AS1010 / 1110 / 210 / 2110 / 2120 / 410 / 4110 / 810 / 8110 and GV-EV48. The section numbers listed here refers to the GV-AS Controller User Manual. Set network configurations Assign a static IP address or set up DDNS to map a dynamic IP address to a static domain name.
4. Setting GV-AS Controller on GV-ASManager After setting up the Web interface, connect the GV-AS Controller to a GV-ASManager. Through GV-ASManager, you can set up the doors and enroll cards. The section numbers listed here refers to the GV-ASManager User Manual. Install GV-ASManager Install GV-ASManager from the supplied software DVD. Chapter 2 Installation Set GV-AS Controllers Establish connection between the controllers and GV-ASManager. 4.2.
5. Optional Devices for GV-AS100 / 110 / 120 To access GV-AS100 / 110 / 120 on a network, an optional device GV-ASBox or GV-ASNet is required. GV-ASBox also supports connection with additional input devices, output devices and readers through Wiegand interface and RS-485 interface. GV-ASNet supports additional readers through RS-485 connection. You will need to first complete the physical wiring of GV-ASBox or GV-ASNet before accessing the Web interface.
5.1 Physical Wiring of GV-ASBox and GV-ASNet The section numbers listed here refers to the GV-AS Controller User Manual. Physical Wiring of GV-ASBox Physical Wiring of GV-ASNet Connect GV-AS100 / 110 / 120 Connect GV-AS100 / 110 / 120 Connect GV-ASBox with GV-AS100 / 110 / 120. 9.1.4.A Connecting GV-AS100 / 110 / 120 Connect GV-ASNet with GV-AS100 / 110 / 120. 9.2.4.
5.2 Accessing the Web Interface of GV-AS100 / 110 / 120 The section numbers listed here refers to the GV-AS Controller User Manual. Set network configurations Assign a static IP address or set up DDNS to map a dynamic IP address to a static domain name. Chapter 7 Installing on a Network Set card readers Set Wiegand readers (ASBox only) 9.3.2.A Function Setting Define the connected readers by selecting the corresponding doors / gates. Set RS485 or TCP/IP readers 9.3.2.
