User's Manual

ManualsBrandsGEP TECHNOLOGY ManualsAudio EquipmentBLUETOOTH PORTABLE SPEAKER

Parts:

Charge:

Initial set up via Bluetooth

1. Turn on the Bluetooth™ Speaker by pressing up top control panel.

2. Wait for approximately 10 seconds,the speaker will go into pairing mode and will produce a “beep”tone.The bottom red led light will flash.

3. Turn on a device such as an ipod,iphone or mp3 device and go to:Setting>General>Bluetooth.Click on the bluetooth GP-508 will then appear on the device.Click on the GP-508. The device is now connected and paired with the speaker.If the device prompts for a pair

code,enter:”0000”

4. If pairing is not successful within 150seconds,the system will search for the last paired device.To restart the pairing process,turn off the speaker and repeat step 1.If the initial set up connection is succesful,the next time the speaker is turned on,the speaker will

automatically pair to the last device it was connected with.

5. Touch V+ for 1 second to increase the volume.When maximum volume has been reached, a tone indicator will sound.

6. Touch V- for 1 second to decrease the volume.When minimal volume has been reached ,a tone indicator will sound.

7. Touch

for 1 second to listen to the next song.

8. Touch

for 1 second to listen to the previsous song.

NOTE:

1. The bluetooth speaker only connects to one device at a time.Turn off the bluetooth speaker in order to pair the device with another bluetooth device.

2. The maximum transmission between the bluetooth speaker and a device is 10 meters or 32 feet.

3. Interference may occur during playback when using the bluetooth function near other wireless devices.If playback through bluetooth is problematic,move the bluetooth speaker

and the playback device to a different location,or use the 3.5mm audio cable jack instead of the bluetooth function.

WARNING:

The built-in rechargeable battery is not replaceable.Do not remove or replace battery.Dispose of unit properly.Do not dispose unit in trash or fire.

Connecting with an audio cable

The bluetooth connection can be switched to a wired connection by plugging in the 3.5mm audio jack.

The volume key function will be available in the wired connection mode.Simply unplug the 3.5mm audio jack to

revert back to the bluetooth connection.

BLUE TOOTH SPEAKER MANUAL

1,Previous song

2,Volum+

3.Volum –

4,Next song

5,Audio line in jack

6,USB charge port

7,ON/OFF

Fully charge the speaker before use.

Connect the speaker to the PC C via provided USB cable

When the bottom RED LED flash approximately 15 times, it means the battery is low, please recharge the speaker. The solid RED LED will appear when speaker is on

charged. The RED LED goes out when charge is finished

Specification

Rating Power: 2.4w x 2pcs

Max power: 3w x 2pcs

Signal To Noise Ratio: >88dB

Frequency Response: 100Hz-20kHz

Distortion: <10%

Battery Li-ion: 3.7v

Battery Capacity: 900mAh

Battery Charging Voltage: 5V

Charger Time: 3 hours max

Playbackt time: 5hours

Driver Unit: 40mm, 4 Ohm ,Power: 2.4 W

Dimension: 13x6x5.5 cm

Transmission Distance: 10m

Work Frequency: 2.402-2.480GHz

Bluetooth Model:

V3.0+EDR

Summary of content (2 pages)

PAGE 1
BLUE TOOTH SPEAKER MANUAL Parts: 1,Previous song 2,Volum+ 3.Volum – 4,Next song 5,Audio line in jack 6,USB charge port 7,ON/OFF Charge: Fully charge the speaker before use. Connect the speaker to the PC C via provided USB cable When the bottom RED LED flash approximately 15 times, it means the battery is low, please recharge the speaker. The solid RED LED will appear when speaker is on charged. The RED LED goes out when charge is finished Initial set up via Bluetooth 1. 2. 3. 4. 5. 6. 7. 8.
PAGE 2
Making and accepting a phone call (built in mic) The exchange Bluetooth speaker has a built-in Microphone, you can make and accept calls via the speaker using Bluetooth. 1, To answer a call: When you have a call, please press the PLAY/PAUSE key. If you don't want to answer the call please do not press down PLAY/PAUSE key.