Users Manual MODEL : Picasso (PAL)
Contents Contents.............................................................................................................. 2 SAFETY ADVICE:.............................................................................................. 4 Attention: PLEASE NOTE.......................................................................... 10 ACCESSORIES:............................................................................................... 11 SCREEN INSTALLATION: .......................................
Fine Tune................................................................................................................................................ 41 TV SOUND ........................................................................................................ 42 Mode........................................................................................................................................................ 42 Volume ......................................................................
SAFETY ADVICE: This symbol is intended to alert the user to un-insulated “dangerous voltage” within the appliance, which is so high that it can lead to an electric shock. WARNING TO AVOID DANGER OF BURNS OR ELECTRIC SHOCKS, THE DEVICE SHOULD NOT BE PLACED IN THE RAIN OR IN A DAMP ENVIRONMENT. This symbol is intended to alert the user to important operating and maintenance advice that accompanies the appliance. WARNING This maintenance information is only intended for qualified customer service employees.
SAFETY ADVICE: Always handle the monitor with care. To reduce the risk of burns, electric shocks and other injuries, always follow this safety advice during assembly, use and maintenance of your appliance. 1) Read through all instructions carefully. 2) Maintain these instructions in good condition. 3) Heed all warning advice. 4) Follow all instructions. 5) Do not use the equipment near to water. 6) Only clean the appliance with a dry cloth. 7) Do not block the ventilation slots.
SAFETY ADVICE Follow all safety instructions. Un-plug the monitor from the mains before cleaning. To clean, wipe with a damp cloth, do not use any liquid detergent or sprays. Do not place the monitor near to water, e.g. baths, sinks, washing machines, swimming pools, etc. Never connect accessories which have not been expressly permitted by the manufacturer. Such accessories could increase the risk of burns, electric shocks and other injuries.
SAFETY ADVICE 100-240V AC Ensure that there is good ventilation. Ventilation slots can be found in the monitor housing to prevent over-heating. Under no circumstances should these slots be blocked by objects, additionally the monitor should not be placed on a bed, sofa, rug or similar surface. Do not place the appliance in close proximity to radiators or any heat source.
SAFETY ADVICE Do not overload wall mounted plug sockets or extension leads. Overload can lead to burns or electric shocks. Do not stick objects into the openings on the appliance, otherwise you will touch particularly dangerous voltage points and you could damage appliance parts. Never allow any kind of liquid to penetrate the monitor. Protect the antenna cable between the inside and outside of the building, thus preventing the penetration of rainwater.
SAFETY ADVICE: Should replacement parts be necessary to repair the appliance, ensure that the customer service technician carrying out the repairs uses parts which have been expressly recommended by the manufacturer, or which have the identical qualities of the original parts. Unlicensed parts could cause further damage to the appliance. After each repair or maintenance check, please ask the customer service technician to carry out a safety check to ensure that the Monitor is working without faults.
Attention: PLEASE NOTE Picture freezing Please do not leave a single image (e.g. from a video game) showing on the plasma or LCD monitor, this can lead to the screen freezing. This phenomenon is also known as ‘Screen Burn’. In order to avoid this phenomenon, please reduce the brightness and contrast of the monitor if a single image is showing.
ACCESSORIES: 1 x Electricity cable 1x Instruction manual 1 x Remote control 2 x Alkaline batteries for the remote control 1 x Foot stand 1 x Service guarantee card 11
SCREEN INSTALLATION: Installation: Stand – Table User´s Guide 1. 2. If not assembled, screw the bar into the foot stand (see Diagram) 3. Attach the foot stand to the appliance Use screw type A (8x18) for this. 4. B-Screw in (4X30) A-screw 5.
SCREW Fully insert the stand in the stand opening.
CONNECTIONS ON THE REAR OF THE APPLIANCE: Connections on the rear of the appliance 1. 2. 3. 4. 5. 6. 7. 9. 10. 11. 12. 13. 8. Connections on the rear of the appliance 1.TV- Antenna-BOX Connection to a TV antenna cable for an analogue television using an antenna, e.g. cable TV. 2.SCART (Euro connector) SCART 1: Half-SCART (CVBS only input). Box 1 3.SCART (Euro connector) SCART2: Full-SCART-connector (CVBS & RGB input/output).
only available if the movie over DVB-S reiceiver or DVD Player supports Dobly Digital or DTS signal. 5. Coaxial (digital) Audio Output (RCA yellow) Only available in HDMI mode Connect the TV over RCA with an external 5.1 amplifier. Supports Dolby Digital and DTS signals. This interface is activated in HDMI mode (not in analog TV mode). The 5.1 sound is only available if the movie over DVB-S receiver or DVD Player supports Dobly Digital or DTS signal. 6.
KEY CONTROL ON THE CASE Following buttons are available on the TV to navigate without remote control. Key Name Power Key Operation ► Power on / off ► Activates main OSD when no main OSD activated Menu Key ► Navigates parent menu when main OSD activated ► Stops auto frequency search ► Activates source select OSD when no main menu activated.
REMOTE CONTROL Remote Control Picture Works only if the TV supports DVB-T Tuner 17
Remote control Key Operations Key Name Operation 1.Power ► Power On/Off 2.Menu ► Same as Menu key on keypad. 3. Up ► Same as Up key on keypad 4. Down ► Same as Down key on keypad 5. Right ► Same as Right key on keypad 6. Left 7. Select 8. Info ► Same as Left key on keypad ► Same as Select key on keypad ► Displays input source information ► Displays current sleep timer value by minute when no sleep timer OSD activated 9.
25. TV ► If current input source is not TV, changes to TV input source. 26. 0~9 ► Enters digit value to change program directly. 27. TTX ON ► If main input source is TV that includes TTX information, enters TTX display mode. 28. TTX MIX ► If TTX mode on, toggles TTX mix and TTX full display mode. 29. TTX RED/GREEN/ CYAN/YELLOW 30. TTX HOLD ► Sends TTX Red / Green / Cyan/ Yellow command. ► Holds current TTX page. 31. TTX REVEAL ► Reveals concealed information. 32.
Basic Operation Turning PDP/LCD TV On And Off Press Power button on the remote control. The PDP/LCD will turn on and you will be ready to use its features. You can also use the Power key on the front panel. Sometimes there is also a Power key on the back panel to switch the device completely OFF or into the standby mode. Select Source Press Source button on the remote control. Then you can see the source list menu shown as below. Press CH+ / CH- button on the remote control to select the source.
Volume Control Press VOL+ / VOL- button on the remote control to adjust the volume level. Press MUTE button on the remote control when you need to cut the sound temporarily.
OSD Menu Structure . OSD (On Screen Display) allows users to control or adjust various features and settings in accordance with his/her preferences. . Press the MENU button on the remote control to see the main OSD menu. Example of OSD Menu 1. Main Menu Press the MENU/ button on the remote control to enter the main OSD menu. First, select Main menu item you need with CH+ & CH- button. To select a main menu items, just press VOL+ or ENTER button on the Remote Control. 2.
PICTURE ▶ Picture Mode 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select a favorite Picture mode with VOL+/VOL- button. ☞ Standard -> Movie -> Mild -> Custom -> Dynamic -> Standard -> … 5. Press Exit button to return.
PICTURE ▶ Custom 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select Custom and press ENTER button to enter the sub menu. Then the custom sub mode appears. 5. You will see the picture setting bars. You can adjust each values of the custom setting, but the changed values are stored as in Custom mode. 6. Press Menu button to return.
PICTURE ▶ Color Tone Your PDP/LCD has 5 screen temperatures (color settings). 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select the Colour Tone with CH+/CH- button. 5. Select a favorite colour Tone with VOL+/VOL- buton. ☞ WARM 1, 2 Screen seems warm: Strong Red. ☞ Normal Normal: Factory default. ☞ Cool 1, 2 Screen seems cool: Strong Blue. 6. Press Exit button to return.
PICTURE ▶ Size 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select the Size with CH+/CH- button. 5. Select a favorite Size with VOL+/VOL- button. ☞ Auto Wide -> Wide -> Panorama -> Zoom -> 4:3 -> 14:9 -> Auto Wide -> … 6. Press Exit button to return.
PICTURE ▶ NR 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select the NR with CH+/CH- button. 5. Select a favorite NR with VOL+/VOL- botton.. ☞ Low -> Middle -> High -> Off -> Low -> … 6.
TV CHANNEL ▶ Country 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu. 3. Press ENTER to enter the sub menu. 4. Select the Country with CH+/CHbutton. 5. Select your Country with VOL+/VOL- button. 6. Press Exit button to return.
TV CHANNEL ▶ Auto Store 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Auto Store with CH+/CHbutton and press ENTER button. 5. Then you can start the tuning bar. PDP/LCD will execute auto program searching. While searching channel after selecting Start with ENTER button, you can also stop channel searching if you select Stop.
TV CHANNEL ▶ Manual Store 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Manual Store and Press ENTER to enter the sub menu.
TV CHANNEL ▶ Manual Store ▶ Prog. 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button and press ENTER button. 3. Select the Manual Store menu with CH+/CH- button on the remote control. 4. Select the Prog. menu with CH+/CHbutton on the remote control. 5. You can select the Prog using VOL+/VOL- button.
TV CHANNEL ▶ Manual Store ▶ Colour System 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button. 3. Select the Manual Store menu with CH+/CH- button and press ENTER button. 4. Select the Colour System menu with CH+/CH- button on the remote control. 5. You can select the Colour System using VOL+/VOL- button.
TV CHANNEL ▶ Manual Store ▶ Sound System 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Select the Manual Store menu with CH+/CH- buttonand press ENTER button. 4. Select the Sound System menu with CH+/CH- button on the remote control. 5. You can select the Sound System using VOL+/VOL- button.
TV CHANNEL ▶ Manual ▶ Store Channel 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button and press ENTER button. 3. Select the Manual Store menu with CH+/CH- button on the remote control. 4. Select the channel menu with CH+/CH- button on the remote control. 5. You can change AIR/Cable using ENTER button 6. You can also operate the Channel using CH+/CH- buitton.
TV CHANNEL ▶ Manual Store ▶ Search 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Select the Manual Store menu with CH+/CH- button and press ENTER button. 4. Select the Search menu with CH+/CH- button on the remote control. 5. Press ENTER to enter the sub menu. 6. You can operate the Search using CH+/CH- button.
TV CHANNEL ▶ Manual Store ▶ Store 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Select the Manual Store menu with CH+/CH- button on the remote control. 4. Select the Store menu with CH+/CHbutton on the remote control. 5. Press ENTER to enter the sub menu. 6. You can Store with ENTER button.
TV CHANNEL ▶ Add/Delete 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Select the Add/Delete menu with CH+/CH- button on the remote control. 4. Press ENTER to enter the sub menu. Then you can see the favorite program list. 5. You can select a program with CH+/CH- button on the remote control. ▶ TO EDIT THE LIST You can INSERT, ERASE, SKIP and REPLACE the programs in the list.
TV CHANNEL ▶ Sort 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Select the Sort menu with CH+/CHbutton on the remote control. 4. Press ENTER to enter the sub menu. Then you can see the sort program list. (notice: You can’t see the sort program list on this picture since this picture isn’t a real operating mode but a design mode.) 5. You can select a program with CH+/CH- button on the remote control.
TV CHANNEL ▶ Name 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Select the Name menu with CH+/CHbutton on the remote control. 4. Press ENTER to enter the sub menu. Then you can see the sort program list. 5 You can change a program Name if you want to change the name of the program. ▶ TO CHANGE THE PROGRAM NAME IN THE LIST If you want to change a program Name, press ENTER button.
TV CHANNEL ▶ Fine Tune The Fine Tuning function lets you manually adjust the PDP/LCD tuner if you are difficult tuning analog Channels. 1. Press MENU button to display the main OSD menu. 2. Select the Channel main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Fine Tune with CH+/CHbutton and press ENTER button. Then you can see the adjust bar. 5. Adjust the fine tune with VOL+ or VOL- button.
TV SOUND ▶ Mode Your PDP/LCD has four automatic sound settings (“Standard”, “Music”,“Movie”,:Speech”)that are preset at the factory. You can active either Standard, Movie, Music or News by pressing “SOUND”on the remote control(or by making a selection from the menu) or you can select “Custom” which automatically recalls your personalized sound settings. 1. Press MENU button to display the main OSD menu. 2. Select the Sound main menu with CH+/CH- button on the remote control. 3.
TV SOUND ▶ Volume 1. Press MENU button to display the main OSD menu. 2. Select the Sound main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Volume and press ENTER button to enter the sub menu. Then you can see the Volume bar. 5. Adjust the Volume with VOL+ or VOL- button.
TV SOUND ▶ Balance This control allows you to adjust the balance of the left and right apeaker output. 1. Press MENU button to display the main OSD menu. 2. Select the Sound main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Balance and press ENTER button to enter the sub menu. Then you can see the Balance bar. 5. Adjust the Balance with VOL+ or VOL- button.
TV SOUND ▶ Equalizer You can use the OSD menu to change the Treble, Bass and Balance according to your preference. 1. Press MENU button to display the main OSD menu. 2. Select the Sound main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Equalizer and press ENTER button to enter the sub menu. Then you will see the Equalizer menu bars. 5. Select a gain bar with VOL+, VOLbutton on the remote control and adjust it with CH+/CH- button. 6.
TV SOUND ▶ Auto Volume 1. Press MENU button to display the main OSD menu. 2. Select the Sound main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Auto Volume. 5. You can select On/Off with VOL+ or VOL- button.
TV SOUND ▶ Sound Mode 1. Press MENU button to display the main OSD menu. 2. Select the Sound main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select the Sound Mode 5. Select the Sound Mode with VOL+/VOL- button.
SETUP ▶ Reset 1. Press MENU button to display the main OSD menu. 2. Select the Setup main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Reset and press ENTER button to enter the sub menu. 5. If you want to reset your TV, press ENTER button. Then the system will reset.
SETUP ▶ Time ▶ Clock Set the current time. 1. Press MENU button to display the main OSD menu. 2. Select the Setup main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Time and press ENTER button to enter the sub menu. Then you will see the time menu. 5. Select Clock by pressing VOL+ button. 6. Move the cursor by pressing VOL+, VOL- button and adjust time by CH+ and CH- button.
SETUP ▶ Time ▶ On Timer This PDP/LCD can be set to turn on automatically at specific time that you chose. Before using timer, you must set the PDP/LCD’s Time as described previously. 1. Press MENU button to display the main OSD menu. 2. Select the TIME main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Selet On Timer by pressing VOL+ button. 5. Move the cursor by pressing VOL-, VOL+ button and adjust on time by CH+ and CH- button.
SETUP ▶ Time ▶ Off Timer This PDP/LCD can be set to turn off automatically at specific time that you chose. Before using timer, you must set the PDP/LCD’s Time as described previously. 1. Press MENU button to display the main OSD menu. 2. Select the TIME main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Off Timer by pressing VOL+ button. 5. Move the cursor by pressing VOL-, VOL+ button and adjust off time by CH+ and CH- button.
SETUP ▶ Time ▶ On Time Channel Set the channel when PDP/LCD power turns on automatically. - Available only when the Time is set and On Time is ON. 1. Press MENU button to display the main OSD menu. 2. Select the TIME main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select On Time Channel. 5. Adjust the channel with VOL-, VOL+ button.
SETUP ▶ Time ▶ On Time Volume Set the sound volume level when PDP/LCD power on automatically. - Available only when the Time is set and On Time is ON. 1. Press MENU button to display the main OSD menu. 2. Select the TIME main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select On Time Volume. 5. Adjust the sound volume level with VOL+, VOL- button.
SETUP ▶ Language Set the language to use in OSD. Supported languages are English, French, German, Italian, Spanish, Portuguese, Netherlandish, Slovene. 1. Press MENU button to display the main OSD menu. 2. Select the Setup main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select the language with CH+/CHbutton. 5. Choice the language with VOL+/ VOL- button.
SETUP ▶ OSD Tone 1. Press MENU button to display the main OSD menu. 2. Select the Setup main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select OSD Tone. 5. Adjust OSD Tone level with VOL+, VOL- button.
SETUP ▶ Blue Screen 1. Press MENU button to display the main OSD menu. 2. Select the Setup main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select Blue . 5. You can select On/Off with VOL+ ro VOL- button.
SETUP ▶ TTX Group 1. Press MENU button to display the main OSD menu. 2. Select the Setup main menu with CH+/CH- button on the remote control. 3. Press ENTER to enter the sub menu. 4. Select TTX Group. 5. Chice the TTX Group with VOL+, VOL- butten.
PICTURE (PC) ▶ Picture 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select a favorite VOL+/VOL- button.
PICTURE (PC) ▶ Custom 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select Custom and press ENTER button to enter the sub menu. Then the custom sub mode appears. 5. You will see the picture setting bars. You can adjust each values of the custom setting, but the changed values are stored as in Custom mode.
PICTURE (PC) ▶ Color Tone 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select the Colour Tone with CH+/CH- button. 5. Select a favorite Colour Tone with VOL+/VOL- button.
PICTURE (PC) If you select Custom in the Colour Tone popup window on PC, you can select sub modes like as Red, Green, and Blue.. ▶ Color Tone 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select Colour Tone and press ENTER button to enter the sub menu. Then the Colour Tone sub mode appears. 5. Select Red(R) and press ENTER button to enter the sub menu. Then the setting bar appears. 6.
PICTURE (PC) ▶ Size 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select the Size with CH+/CH- button. 5. Select a favorite Size with VOL+/VOL- button. 6. Press Exit button to return.
PICTURE (PC) ▶ PC 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select PC and press ENTER button to enter the sub menu. Then you will see the sub menu of PC. 5. Select the Auto Adjust with CH+/CH- button and press ENTER button.
PICTURE (PC) ▶ PC 1. Press MENU button to display the main OSD menu. 2. Select the picture main menu. 3. Press ENTER to enter the sub menu. 4. Select PC and press Enter button to enter the sub menu. Then PC sub mode appears. 5. You can adjust each values of the PC setting. * For more detail description refer to the next page.