POSEIDON PE Why compromise User Guide 106169309 POSEIDON PE
Copyright © 2013 Gerni
POSEIDON PE Contents Symbols .................................................................................................4 1 Important safety notes .................................................................................................4 2 Description 2.1 Intended use.............................................................................7 2.2 Operating elements ..................................................................7 3 Before starting the pressure washer 3.
POSEIDON PE Symbols Before starting up your highpressure washer for the first time, this instruction manual must be read through carefully. Save the instructions for later use. Safety instructions marked with this symbol must be observed to prevent danger to persons. This symbol is used to mark safety instructions that must be observed to prevent damage to the machine and its performance. This symbol indicates tips and instructions to simplify work and to ensure a safe operation.
POSEIDON PE or recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the machine. Risk of explosion – Do not spray flammable liquids. Do not clean delicate parts made of rubber, fabric, etc. with the 0° jet. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned to avoid any damage to the surface being cleaned. Do not use the high-pressure hose for lifting loads.
POSEIDON PE 12 months, by an authorised inspector and this report must be saved. The unloader valve is set and sealed at the factory and must not be adjusted. The complete „Accident Prevention Regulations for Working with Liquid Spray Jet Devices“ are available from the Carl Heymanns Verlag KG, Luxemburger Strasse 449, 50939 Cologne or from the appropriate association of employers’ liability insurances. Safety device Locking device on spray gun: The spray gun features a locking device.
POSEIDON PE 2 Description 2.1 Intended use This high pressure washer has been designed for professional use in - agriculture - transport industry - construction industry etc. 2.
POSEIDON PE 3 Before starting the pressure washer 3.1 Setting up the pressure washer (does not apply to POSEIDON 3-39 PE) 1. Before using the pressure washer for the first time, check it carefully to detect any faults or damage. 2. In the event of any damage contact your Gerni dealer immediately. 3. Check whether the oil level is in the middle of the oil inspection glass, oil cup or dip stick. This also applies to machines with gear. 4 Operation and use 4.1 Connections 4.1.
POSEIDON PE 4.1.2 Connecting the high pressure hose and the water hose 1. Connect the high pressure hose to the high pressure inlet by means of the quick coupling. Use max. 50 m extension hose. 2. Before connecting the water hose to the washer, rinse the water hose briefly to prevent sand and other dirt from entering into the washer. 3. Open the tap. NOTE! See chapter 8.3 for required quantity of water and water pressure. In the case of poor water quality (sand, etc.
POSEIDON PE 4.2.2 Switching on the washer when it is connected to open tanks (suction mode) 1. Before connecting the suction hose to the washer, fill the hose with water. During work breaks of more than three minutes, switch off the washer. NOTE! For automatic suction from a tank, watercourse or similar supply, the inlet hose must be filled with water before you start. The suction height 2. Start the washer. 3. Unlock the spray gun and activate it. 4.
POSEIDON PE 5 After using the washer 5.1 Stop the pressure washer 1. Stop the engine. 2. Close the tap. 3. Operate the spray gun until the wasser is depressurized. 4. Lock the safety catch. Switching off POSEIDON PE with electric start 1. Stop the washer by moving the throttle lever to STOP position. 2. Switch off the ignition by turning the key to OFF position. 5.2 Disconnecting supply lines 1. Shut the fuel cock. 2. Remove the water hose from the washer. 5.
POSEIDON PE 6 Maintenance 6.1 Maintenance plan weekly every six months or 500 operating hours as required • 6.2.1 Clean water filter • 6.2.2 Clean high pressure nozzle • 6.2.3 Check oil level 6.2.4 Change oil - Note: First time after 50 hours 6.2.5 Check belts (only belt driven units) • • Maintenance of motor according to separate operating instructions from the engine supplier 6.2 Maintenance work 6.2.
POSEIDON PE 6.2.3 Checking the oil level (does not apply to POSEIDON 3-39 PE) 1. Check whether the oil level is in the middle of the oil inspection glass, oil cup or dip stick. Top up with oil if necessary (see section 8.3 for type of oil). 6.2.4 Changing the pump/ gear oil (does not apply to POSEIDON 3-39 PE) 1. Before changing the oil, allow the pressure washer to become warm. 2. Unscrew/open the plugs/lid at the top and the bottom of the pump. 3. Allow the oil to drain into a suitable container (min.
POSEIDON PE 6.2.5 Check of V-belts 1. Remove the spark plug cable. 2. Dismantle the cover of the V-belts. 3. Check the belts for any damage or missing tension. 4. If required, replace the belts. 5. Mount the cover. 6. Mount the spark plug cable.
POSEIDON PE 7 Troubleshooting Fault Pressure drop Cause Remedy > Air in the system • Vent the system by operating the spray gun several times at short intervals. If necessary, dismount the lance (see section 4.2.2). > High-pressure nozzle blocked/worn • Clean/replace the highpressure nozzle. > Pressure control on the lance is not set correctly • Set the required working pressure. > Engine speed too low • Contact Gerni Service Department. > Warm/loose belts • Contact Gerni Service Department.
POSEIDON PE Cause Fault The motor stops When a detergent injector is used Remedy > Low oil level in engine • Fill with oil. > Low oil level in pump • Fill with oil > Injector is dirty or suction hose is blocked • Clean. > Detergent tank is empty • Fill the detergent tank. > The lance is not set to low pressure • Adjust the lance to low pressure. 8 Further information 8.1 Recycling the pressure washer If the pressure washer is discarded, make it unusable immediately 1.
POSEIDON PE 8.3 Technical data POSEIDON 3-39 PE POSEIDON 5-50 PE POSEIDON 5-64 PE+ POSEIDON 5-75 PE Working pressure bar 165 240 250 250 Water flow (max) l/h 750 800 1000 1180 Water flow Q IEC l/h 810 870 1050 1300 Max. water inlet temperature °C 60 60 60 60 Min./max. water inlet pressure bar 1/10 1/10 1/10 1/10 Dimensions (LxWxH) mm 762x546x603 1041x546x635 1016x660x965 1270x787x1092 Noise power level, LWA dB(A) 93.2 91 93.4 99 Thrust N 31.9 42.3 54.4 71.
Nilfisk-Advance Pty LTd Unit 1/13 Bessemer Street Blacktown NSW 2148 Phone: 1300 556 710 E-mail: customerservice@nilfisk-advance.com.