Why compromise Super 130.3 Super 135.3 Super 140.3 Super 145.3 128332556 User Guide Super 130.3 Super 135.3 Super 140.3 Super 145.
Printed in China Copyright © 2014 Gerni
Contents 1 Introduction................................................................................................... 4 1.1 Symbols used to mark instruction........................................................................4 2 Safety precautions and working techniques.................................................4 3 Before you start using your high pressure washer................................. 10 3.1 Mounting of trolley handle, hose hook and hose reel...................................
1 Introduction 1.1 Symbols used to mark instruction All pictograms attached to the high pressure washer and its components are shown and explained in this manual. Safety instructions marked with this symbol must be observed to prevent personal injury or serious damage to property. Caution where there is a risk of damaging the machine or its individual components. This symbol indicates tips and instructions to simplify work and to ensure a safe operation of the high pressure washer.
maintenance and when replacing parts or converting the machine to another function. • Observe the national safety regulations issued, for example, by the employers liability insurance association, social security institutions, occupational safety and health authorities or other organizations. Accessories and spare parts • To ensure the machine safety only use original spare parts from Gerni or approved by Gerni.
during operation. Transporting the high pressure washer • When transporting the machine in or on a vehicle, it must be secured, e.g. with straps, so that it cannot slip or tip over. • Gerni recommends that the machine is positioned horizontally on the backside, when transported in or on a vehicle. Detergents • This machine has been designed for use with cleaning agents supplied or recommended by Gerni. The use of other cleaning agents or chemicals may adversely affect the function of the machine.
machine should include a residual current device that will interrupt the supply if the leakage current to earth exceeds 30 mA for 30 ms. • Inadequate extension cables can be dangerous. If an extension cable is used, it shall be suitable for outdoor use, and the connection has to be kept dry and off the ground • Gerni recommends use of an extension cable drum when cable extension is needed which keeps the socket at least 60 mm above the ground.
• • • • • • • • • • • • • • could be a danger of explosions. If any doubt arises contact the local authorities. It is not allowed to clean asbestos-containing surfaces with high pressure. Never draw in fluids containing solvents (e.g., gasoline, heating oil, paint thinner or acetone) These substances damage the materials used in the machine. Their spray is highly combustible, explosive and poisonous.
water supply. • Wind up electrical cable and high pressure hose – to avoid damage of cable, plug, high pressure hose and fittings. • Always empty pump, hose and accessories of water after use of the machine and prior to storing. Maintenance and repairs WARNING! • Always disconnect the electrical plug from the socket prior to maintenance, cleaning and repair. • Any repair should always be made in Gerni authorized workshop with original Gerni spare parts.
3 Before you start using your high pressure washer A See the pictorial quick reference guide – unpacking. Illustration shows the operation elements and how to prepare your machine for use. Operation elements 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
4 Operating your high pressure washer B See the pictorial quick reference guide – operating your high pressure washer. 4.1 Connection of high pressure hose Attach the high pressure hose (4) to the spray handle (7). Detach the high pressure hose by pressing the pawl (A). B2 Mount the high pressure hose on the outlet (3). B1 4.2 Mounting of spray lance and Click&Clean nozzles B3 Push the spray lance (6) into the spray handle (7), twist and release.
When connecting the machine to operate from pressure less water supplies – always use additional filtering to secure that impurities are not sucked in. Hose length should be max. 3 meter and of minimum ½". To meet these requirements, Gerni recommends that you use the original Gerni suction hose kit. The Machine is designed for suction up to 100 cm above water surface. • Position the machine at max. 1.0 meter above the water surface. Detach the high pressure hose from the outlet.
5 Fields of application and working methods 5.1 General Efficient high presure cleaning is achieved by following a few guidelines, combined with your own personal experience of specific cleaning tasks. Accessories and detergents, when correctly chosen, can increase the efficiency of your pressure washer. Here is some basic information about cleaning. 5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt.
5.2 Typical fields of application Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Gerni in association with accessories and detergents. 14 Task Accessories ‘Click Cleaning method & Clean’ Car Car nozzle, auto brush, underchassis nozzle, Foam sprayer, Car Combi Cleaner 1. Apply Car Combi Cleaner with the foam sprayer. Always start from the bottom and work upwards. Let Car Combi Cleaner act for at least 5 min. 2.
6 After using the pressure washer C O See the pictorial quick reference guide – storing the high pressure washer. I The high pressure washer should be stored in a frost free room! Should the machine by a mistake be frozen, it will be necessary to check it for damages. 6.1 Stopping the high pressure washer Shut off the water supply and activate the trigger of the spray handle and let the machine run until no more water runs out of the nozzle.
D3 Flush the nozzle backwards with water. Cleaning of machine vents D4 The machine should be kept clean so as to let cooling air pass freely through the machine vents. Greasing of O-rings D5 To ensure an easy connection and that O-rings do not dry up the couplings should be greased regularly. 8 Troubleshooting To avoid unnecessary disappointments, you should check the following before contacting the Gerni service organization.
9 Accessories and detergents Only use original accessories and detergents. For further information, see www.Gerni.com. 10 Warranty Conditions Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
11 Main technical Data Super 130.3 Super 135.3 Super 140.3 Super 145.3 230-240 50 2.0 9.0 230-240 50 2.0 9.0 230-240 50 2.1 9.5 230-240 50 2.1 10 Class II Class II Class II Class II Protection degree Hydraulic specifications Rated pressure Max. pressure Rated water flow Max. water flow Max. water inlet pressure Max. water inlet temperature Max. water inlet temp. suction mode V Hz kW A Class I/ Class II IP xx IPX5 IPX5 IPX5 IPX5 MPa/bar MPa/bar l/min/l/h l/min/l/h Mpa/bar °C °C 12.
12 Declaration of Conformity We, Nilfisk-Advance A/S Sognevej 1 DK-2605 Broendby DENMARK, hereby solely declare that the products: Product Description Type HPW - Consumer 230-240 V 1~, 50 Hz – IP X5 Gerni Super 130.3, 135.3, 140.3, 145.
A1 A2 A3 A4 A5 A6
B1 B2 B6 B7 B10 B15 Max. 60°C B3 B4 B5 B8 B9 B11 B12 B13 B14 B16 B17 Max.
O I C1 C1 C2 C3 C4 C5 C6 C7 f d b a c b D1 D5 D2 D3 D4
AUSTRALIA: NEW ZEALAND: Nilfisk-Advance Pty Ltd Unit 1/13 Bessemer Street Blacktown NSW 2148 Accent Tools Ltd 232 Bush Rd Albany Auckland 0632 Phone: 1300 556 710 E-mail: sales@gerni.com.au Phone: 09 968 2610 E-mail: sales@accent-tools.co.