V100 USER’S MANUAL Rugged Mobile Computing Solutions
July 2010 TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE The information in this manual is subject to change without notice.
For the latest version of the manual, please visit the Getac website at www.getac.com. ENERGY STAR® is a government program that offers businesses and consumers energy-efficient solutions, making it easy to save money while protecting the environment for future generations. Please reference ENERGY STAR® related information from www.energystar.gov. As an ENERGY STAR® Partner, Getac Technology Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Spending a large portion of time in low-power mode not only saves energy, but helps equipment run cooler and last longer. Businesses that use ENERGY STAR® enabled office equipment may realize additional savings on air conditioning and maintenance. Over its lifetime, ENERGY STAR® qualified equipment in a single home office (e.g., computer, monitor, printer, and fax) can save enough electricity to light an entire home for more than 4 years.
Table of Contents Chapter 1 Getting Started................................................................. 1-1 Getting the Computer Running ............................................1-2 Unpacking ............................................................................1-2 Connecting to AC Power ..................................................1-3 Opening and Closing the Cover ......................................1-4 Operating in Tablet Mode .................................................
Function Keys .......................................................................2-6 Fn Key....................................................................................2-6 Hot Keys ................................................................................2-6 Using the Software Keyboard................................................2-8 Using the Touchpad ................................................................2-9 Configuring the Touchpad .............................................
Power Management ..............................................................3-8 Hibernation...........................................................................3-9 Power-Saving Tips ..................................................................3-10 Chapter 4 Expanding Your Computer ............................................ 4-1 Connecting an External Monitor (Optional) .......................4-2 Connecting a Serial Device ..................................................
Drivers on the First Page .....................................................6-3 Drivers on the Second Page .............................................6-4 Drivers on the Third Page ...................................................6-5 Installation for Windows Vista ................................................6-8 Drivers on the First Page .....................................................6-8 Drivers on the Second Page .............................................6-9 Drivers on the Third Page ....
Location Guidelines............................................................8-4 General Guidelines.............................................................8-4 Cleaning Guidelines ...........................................................8-5 Battery Pack Guidelines.....................................................8-5 Touchscreen Guidelines.....................................................8-6 When Traveling ........................................................................
On the Use of the RF Device..................................................B-7 USA and Canada Safety Requirements and Notices ...
Chapter 1 Getting Started Congratulations on purchasing this rugged computer. This chapter first tells you step by step how to get the computer up and running. Then, you will find a section briefly introducing the external components of the computer.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: Notebook computer Accessories: AC adapter AC power cord Grid-type hand strap Driver disc Stylus (option) Digitizer pen and size “AAAA” battery (option) Inspect all the items. If any item is damaged or missing, notify your dealer immediately.
Connecting to AC Power The computer operates either on the external AC power or internal battery power. It is suggested that you use AC power when you start up the computer for the very first time. CAUTION: Use only the AC adapter included with your computer. Using other AC adapters may damage the computer. 1. Make sure that the computer is turned off. 2. Plug the DC cord of the AC adapter to the power connector of the computer (). 3.
CAUTION: When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3.
Latch B Latch A Getting Started 1-5
Operating in Tablet Mode In addition to being used as a regular notebook computer (Laptop mode), your computer can also be operated in Tablet mode. In Tablet mode, you operate the computer with a stylus or digitizer pen, or a fingertip, instead of a keyboard or mouse. 1. Open the top cover so that it is almost perpendicular with the keyboard of the computer. 2. Turn the display counter-clockwise by 165o. CAUTION: Do not rotate the display more than 165o, or attempt to rotate the display clockwise. 1.
2. Position the latch B on the display side, then bring latch A down () to fix the display in place. Latch B Latch A In Tablet mode, the computer can be operated while holding it as shown. To return to Laptop mode, perform the steps for changing the computer into Tablet mode in reverse order.
Turning On and Off the Computer Turning On 1. Make sure that the computer is connected to AC power. 2. Press the power button ( ). 3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer.
Attaching the Hand Strap The hand strap can be attached to any two sides of the four (option) corners of your computer. Standard setup: two buckles on the left/right front side of your computer. To release, press on the right spring latch first to detach the right side. Then release the left side.
Optional setup: buckles on four corners of your computer. CAUTION: The strap has been designed to carry only the weight of the computer. Therefore, be sure that the strap does not carry a weight that exceeds the weight of the computer. The strap may accidentally come loose from the computer. Do not use a strap that is damaged or about to tear.
Taking a Look at the Computer NOTE: Depending on the model you purchased, the appearance of your computer may not be exactly the same as those shown in this manual. Front Components Ref Component Description Hand Strap Holder The hand strap can be attached to the two holders for convenient handling of your computer. OSD Control Button Toggles the OSD (On Screen Display) control panel ON and OFF. P1 Can be re-defined using the Button Manager utility.
Ref Component Description RF Button Toggles the wireless LAN /Bluetooth/3G radio frequency ON and OFF. P3 Can be re-defined using the Button Manager utility. (See “Using Button Manager” in Chapter 7 for information.) Reset Button Serves as the Ctrl+Alt+Del keyboard keys. P4 Can be re-defined using the Button Manager utility. (See “Using Button Manager” in Chapter 7 for information.) Software Keyboard Button Shows or hides the software keyboard on your LCD display.
Rear Components Ref Component Description Hand Strap Holder The hand strap can be attached to the two holders for convenient handling of your computer. Audio Output Connector Connects a set of headphones, external speakers with amplifier, or an audio recording device. Microphone Connector Connects an external microphone. Kensington Lock Locks the computer to a stationary object for security. VGA Connector Connects an external display monitor.
Right-Side Components Ref Component Description Battery Pack Compartment Inside is the battery pack that supplies power to your computer when external power is not connected. Hard Disk Drive Compartment Inside is the hard disk drive. Left-Side Components Ref Component Power Connector 1-14 Getting Started Description Connects the AC adapter.
USB Port Ref Component eSATA/USB Combo Port Connects a USB device, such as a flash disk, printer, digital camera, joystick, and more. Description Connects an eSATA device such as an external hard drive or optical drive. Can also function as a USB port. RJ-11 Connector Connects the telephone line. RJ-45 Connector Connects the LAN cable. ExpressCard Slot (upper) Accepts an ExpressCard for additional functions (option). PCMCIA Slot (lower) Accepts a PC card for additional functions.
Bottom Components Ref Component Description Expansion Bus Connector Inside is the expansion bus connector for using the Port Replicator option. Memory Slots Inside are the memory slots for expanding the memory size of your computer.
Top-open Components Ref Component Description Webcam Lens (option) Allows you to use your computer’s camera function. GPS Antenna (option) Inside is the antenna for receiving GPS signals. WLAN Antenna Inside is the antenna for wireless LAN (local area network) transmission. WWAN 3G Antenna Inside is the antenna for optional wireless WAN (option) (wide area network) 3G transmission. LCD Screen Displays the output of the computer.
Ref Component Description Light Sensor Detects the surrounding lighting condition for automatic adjustment of the LCD brightness and optional keyboard backlight. Fingerprint Scanner (option) Uses fingerprint verification to protect your computer against unauthorized access. Keyboard Serves as the data input device. Touchpad Serves as the pointing device. Indicators Show the current status of the computer’s devices.
Ref Component (option) Description transmission.
Chapter 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user, you may choose to read only the parts containing information unique to your computer. CAUTION: The computer can get uncomfortably warm when you use it in high temperatures.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk. The computer will automatically load the OS after you turn it on. This process is called booting. NOTE: An operating system is the platform for all your software application programs to run on.
To stop in this mode... Do this... To start up or resume again computer in Standby/Sleep mode by: Hibernation Closing the display cover Pressing the Fn+F10 hot key Pressing the power button Depending on your settings in Windows, you can place the computer in Hibernation mode by: Press the power button. Closing the display cover Pressing the power button If you choose to stop in Standby/Sleep or Hibernation mode, you can return to where you left off the next time you start up the computer.
Using the Internal Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus an Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: Typewriter keys Cursor-control keys Numeric keys Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTE: When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off.
Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead. Function Keys On the top row of the keys are the function keys: F1 to F12. Function keys are multi-purpose keys that perform functions defined by individual programs. Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key.
Key Description Decreases the sound volume. Increases the sound volume. Decreases the LCD brightness (20 levels). Increases the LCD brightness (20 levels). Switches the system sound output off (mute) and on. Switches LCD backlight on and off. Switches the display output when external devices are connected. NOTE: This function only applies to Plug & Play display devices. Serves as the sleep button that you can define with Windows’ Power Options. (See the “Power Management” in Chapter 3.
Using the Software Keyboard When using the computer in Tablet mode, you can use the software keyboard. 1. Press the software keyboard button ( will appear onscreen. ) and the software keyboard (The above is for reference only. The actual one depends on your Windows version.) 2. Enter the characters with the stylus. NOTE: To protect the LCD display, use the included stylus or digitizer pen on your touchscreen.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Double-click Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination.
TABLE NOTE: If you swap the left and right buttons, “tapping” on the touchpad as an alternative method of pressing the left button will no longer be valid. Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vice versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on.
Navigating on the Screen The screen of your computer is touch-sensitive. You can control the location of the cursor/pointer on the screen using your finger or the included stylus or digitizer pen to communicate with the computer. CAUTION: Do not use sharp objects on the LCD display. Doing so may damage the display surface. Use your finger or the included stylus or digitizer pen.
Here are some common terms that you should know when using the touchscreen: Term Action Click/Point Tap gently on the touchscreen. Double-click Tap twice on the touchscreen rapidly. Drag and drop Tap lightly on the touchscreen and move your finger until you reach your destination (drag). Finally, release your finger (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Gestures Actions ( = finger down; = finger up) Zoom (Pinch) Move two fingers apart/toward each other. Rotate or Move two fingers in opposing directions. -orUse one finger to pivot around another. Press and Tap Use zooming to make an item (a photo for example) on the screen larger or smaller. The gesture works in applications that support mouse wheel zooming. Use rotating to move a picture or other item on the screen in a circular direction (clockwise or counterclockwise).
Gestures Actions ( = finger down; = finger up) Twofinger Tap Descriptions The function is defined by applications that support the specific gesture. Tap two fingers at the same time (where the target is in the midpoint between the fingers). Flicks Make quick drag gestures in the desired direction. Flick left or right to navigate back and forward in a browser and other applications. The gesture works in most applications that support back and forward.
Using the Dual Mode Display (Optional) NOTE: Make sure both the touchscreen driver and digitizer driver have been installed properly. Dual mode display incorporates both touchscreen and digitizer functions. The display is set to Touchscreen mode by default. Touchscreen mode provides all the functionalities that an ordinary touchscreen has. When the computer receives signals from the active digitizer pen, the display automatically switches to Digitizer mode.
Term Action Wake up The digitizer pen automatically enters Sleep mode after 30 seconds of inactivity. To start using the pen, tap the tip of the pen to activate it. Move Move the cursor pointed by the digitizer pen. Click/Point Tap gently on the display. Double-clic k Tap twice on the display rapidly. Drag and drop Tap lightly on the display and move your digitizer pen until you reach your destination (drag).
Even when only an external display is in use, the cursor will move on the external display if you touch the surface of the LCD display with the pen or bring the pen close to the surface of the LCD display when the digitizer driver is active. Therefore, do not touch the LCD display when only an external display is in use. The active digitizer feature cannot be used in the BIOS Setup program or when using the full screen in DOS mode.
Using the Hard Disk Drive WARNING: DO NOT replace the hard disk drive by yourself. Refer all servicing to qualified personnel or your dealer. Your computer comes with a removable 2.5-inch SATA (serial ATA) hard disk drive. You can enable AHCI (Advanced Host Controller Interface), a programming interface for SATA host controllers. AHCI defines transactions between the SATA controller and software and enables advanced performance and usability with SATA.
Using OSD Control Panel The OSD Control Panel allows you to easily activate or operate certain functions on your computer. To use the OSD Control Panel: 1. Press the button on the front of your computer. 2. The following screen appears, providing several control buttons. For detailed descriptions of the Control Panel, click the 3. To close the Control Panel, either press the button computer again or click the 2-20 Operating Your Computer button . button.
Using the Fingerprint Scanner (Optional) The fingerprint scanner provides a strong authentication mechanism based on fingerprint recognition. You can log on to your computer or sign in to a web site with your fingerprint instead of a password. You can also encrypt files and folders with your fingerprint. NOTE: You can register a fingerprint only after creating a password for the Windows user account. CAUTION: For the fingerprint file/folder encryption feature, the maximum file/folder size allowed is 2GB.
You can then use the Fingerprint Software to set up how the fingerprint authentication works. For detailed information, click Start All Programs Fingerprint Software Help.
Using the Video Features The video subsystem of your computer features: 12.
Configuring the Display Modes NOTE: When using an external CRT monitor, the resolution depends on the CRT monitor’s supported resolution. Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external monitor that supports higher resolutions.
For a Model without 3G Module Primary Landscape Primary Portrait Secondary Landscape Display Secondary Portrait Display Display Primary Landscape Display Display For a Model with 3G Module Primary Landscape Primary Portrait Display Secondary Landscape Primary Landscape Display Display Display Operating Your Computer 2-25
Using the Audio Features NOTE: To take advantage of the enhanced audio capabilities, the audio driver supplied with your computer must be installed. If you experience interference while recording, try lowering the microphone recording volume.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. NOTE: After connecting an external audio device, make sure that you specify the use of the correct audio device in Windows. Audio Output Connector ( ) can be connected to speakers, headphones, or earphone set. Microphone Connector ( ) can be connected to an external microphone for recording voice or sound.
Using G-Camera Lite G-Camera Lite allows you to take pictures with the Webcam, if supplied with your computer. To start G-Camera Lite, click Start All Programs G-Camera Lite G-Camera Lite. The camera control panel appears. Mode Current settings Setting buttons for different modes Click the Shutter button or press Enter to take photos. For detailed descriptions of G-Camera Lite, click the button 2-28 Operating Your Computer .
Using the Communication Features Using the Modem NOTE: To take advantage of the modem feature, the modem driver supplied with your computer must be installed. The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line.
Using the LAN NOTE: To take advantage of the LAN feature, the LAN driver supplied with your computer must be installed. The internal 10/100/1000Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN Depending on your model, an internal mini PCI-E wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes support WEP (Wired Equivalent Privacy) 64/128-bit data encryption IEEE 802.11a/g/n standard compliance Technology 802.11a 802.11g 802.
Turning Off/On the WLAN Radio NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to turn off wireless LAN when using your computer in the airplane. Your computer has a built-in Fn+F2 WLAN hot key to switch the WLAN on/off. If you need to temporarily turn off the radio, press Fn+F2. To resume network connection, press Fn+F2 again.
4. Click to select a wireless network to connect to, and then click Connect. 5. Depending on the settings, you may be asked to enter a wireless security password (encryption key). For more information on the Intel PROSet Wireless utility, click Help? in the Intel(R) PROSet/Wireless window. Using the Bluetooth Feature (Optional) NOTE: To take advantage of the Bluetooth feature, the Bluetooth driver supplied with your computer must be installed.
The status of the Bluetooth connection is indicated by the Bluetooth icon located in the taskbar in the lower-right part of the screen. Status Icon On (blue with white logo). Connected (blue with green logo) You can use the Bluetooth Utility to configure Bluetooth connection settings and transfer files. Connecting to another Bluetooth Device 1. Make sure that the target Bluetooth device is turned on, discoverable and within close range. (See the documentation that came with the Bluetooth device.
2. To search for Bluetooth devices, use any of the following three methods: Method 1: located in the taskbar in the Right click the Bluetooth icon lower-right part of the screen. Select Explore Bluetooth Places. Method 2: located in the taskbar in the Right click the Bluetooth icon lower-right part of the screen. Select Display Classic View. The Bluetooth utility screen appears. Right click the central icon (the yellow sun) and select Search Devices.
Method 3: Use Windows File Manager to browse to Bluetooth Places and select Search Devices. 3. Select the device you want to connect from the search results. 4. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information. For detailed information on using the Bluetooth Utility, see the Bluetooth Utility Help.
Using the GPS NOTE: To take advantage of the GPS feature, the GPS and GPS filter driver supplied with your computer must be installed. GPS (Global Positioning System) is a constellation of 24 well-spaced satellites that orbit the Earth and make it possible for devices enabled with GPS receivers to pinpoint their location. You need to install third-party GPS navigation software to take advantage of the GPS feature.
Chapter 3 Managing Power Your computer operates either on external AC power or on internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
CAUTION: After the computer has been fully recharged, do not immediately disconnect and reconnect the AC adapter to charge it again. Doing so may damage the battery. NOTE: The battery level may automatically lessen due to the self-discharge process (0.21 % per day), even when the battery pack is fully charged (100 %). This happens no matter if the battery pack is installed in the computer. Checking the Battery Level NOTE: Any battery level indication is an estimated result.
The value of the corresponding green segment indicates the relative percentage of the battery charge. The battery pack is fully discharged when you see no segment glowing green. Replacing the Battery Pack CAUTION: There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. Do not attempt to disassemble the battery pack.
4. Pull on the ribbon strip to remove the battery pack. 5. Slide the new battery pack all the way into the slot. Make sure to observe the correct orientation (the ribbon strip must face outward for future battery back removal). 6. Close the compartment cover to secure the battery pack.
Battery Low Signals and Actions When the battery is low, Windows gives warning messages and the Battery Charge Indicator ( ) blinks yellow to alert you. Immediately save your data upon Battery Low. The remaining operating time depends on how you are using the computer. If you are using the audio subsystem, PC card, hard or USB flash disk, the battery might run out of charge very quickly.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time. In general, Windows’ power management works in this way: What... When...
Hibernation Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the computer can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shuts down.
Power-Saving Tips Aside from enabling your computer’s power saving mode (see previous section), you can do your part to maximize the battery’s operating time by following these suggestions. Do not disable Power Management. Decrease the LCD brightness to the lowest comfortable level. Shorten the length of time before Windows turn off the display. Many USB devices use power just by being connected. If you use a USB mouse, you can save power by disconnecting the mouse and using the touchpad.
Chapter 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor (Optional) If you want the benefits of a larger display screen with higher resolution, you can connect an external display monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s D-type signal connector to the computer’s VGA connector. 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
CAUTION: Do not disconnect the external monitor while the computer is in the Standby/Sleep mode or Hibernation mode. If no external monitor is connected when the computer resumes, the LCD might not display properly.
Connecting a Serial Device Your computer has one or two serial port (depending on model) for connecting a serial device such as a serial mouse or serial communication device (modem). Follow this procedure to connect a serial device: 1. Make sure the computer is not turned on 2. Plug the device cable to the serial port on the rear of the computer. 3. Turn on the computer. NOTE: Portable modems that derive power through the serial port cannot be used with the computer.
Connecting a USB Device Your computer has a USB port for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. NOTE: The eSATA/USB Combo port can also function as a USB port. The USB port support transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices. To connect a USB device, simply plug the device cable to one of the USB ports.
Connecting an eSATA Device Your computer has an eSATA/USB Combo port for connecting eSATA devices (such as an external hard drive and external optical drive) / USB devices (see previous section). The port supports SATA II with transfer rate up to 3.0Gbit/s. It can provide 5V power if a certified USB-eSata combo cable is used. To connect an external eSATA device, simply plug the device cable to the eSATA port.
Using Smart Cards (Optional) Your computer may have a smart card slot for additional security feature, providing tamper-proof storage of user and account identity. A smart card is a type of plastic card embedded with a computer chip that stores and transacts data between you (user) and the computer. You need to install third-party smart card software to take advantage of the smart card feature. Inserting and Removing a Smart Card To insert a smart card: 1. Locate the smart card slot. 2.
To remove a smart card: 1. Make sure that the third-party smart card software is not accessing the smart card. 2. Pull the card out of the slot.
Using PC Cards NOTE: To take advantage of the PC Card interface, the PC Card Controller driver supplied with your system must be installed. Your computer has one or two PC card slots that support CardBus specifications. The slots can accommodate a type II card. Typical type II cards are flash memory, SRAM, modem, LAN, and SCSI cards. Inserting and Removing a PC Card NOTE: Some PC cards require additional system resources.
3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove a PC card: for Windows 1. Double-click on the Safely Remove Hardware icon ( Vista/Windows 7 or for Windows XP) found on the Windows taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the PC card from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4.
Using ExpressCards (Optional) NOTE: The ExpressCard interface is not compatible with the PC card interface. Your computer may have an ExpressCard slot. ExpressCard supports the PCI Express and USB 2.0 serial data interfaces (supporting speeds of up to 2.5 Gbps and 480 Mbps respectively), improving speed in data transfer while conserving power usage. ExpressCard Type The ExpressCard slot can accommodate a 54 mm (ExpressCard/54) or 34 mm (ExpressCard/34) wide ExpressCard.
Inserting and Removing an ExpressCard To insert an ExpressCard: 1. Locate the ExpressCard slot on the left side of the computer. 2. Slide the ExpressCard, with its label facing up, all the way into the slot until the rear connectors click into place. Eject button 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove an ExpressCard: 1.
Using the Card Reader NOTE: To use the Card Reader, the SD Reader driver supplied with your computer must be installed. If your hard disk is divided into several drives, make sure that all drives have been formatted before using the Card Reader. Otherwise, you may encounter problems when using the Card Reader. You can use only storage cards. Your Card Reader does not support cards with I/O (input/output) functions such as a wireless network card or Bluetooth card. Your computer has a Card Reader.
To remove a storage card: 1. Double-click My Computer. 2. Right-click the drive with the card and select Eject. 3. Pull the card out of the slot.
Using the Port Replicator (Optional) NOTE: To use the port replicator, the Vehicle Dock driver supplied with your computer must be installed. A port replicator is available as an option. This device eliminates the hassles of having you connect and disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector at the bottom of your computer. 1.
2. Connect your port replicator to the expansion bus connector. For more detailed information, refer to the instructions supplied with the port replicator.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 8 GB on the DDR3 SO-DIMM slot. CAUTION: RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. When inserting or removing a RAM module, do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter.
4. To install the RAM module, match the module's notched part with the socket's projected part and firmly insert the module into the socket at a 20-degree angle. Then push down until the retaining clips lock the module into position. CAUTION: If the RAM module is difficult to insert or difficult to push down, do not force it. Check once more to ensure that the module is positioned correctly. 5. Close the compartment cover and secure with four screws.
Chapter 5 Using BIOS Setup and System Recovery BIOS Setup Utility is a program for configuring the BIOS (Basic Input/ Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features.
BIOS Setup When to Use You need to run BIOS Setup Utility when: You see an error message on the screen requesting you to run BIOS Setup Utility. You want to restore the factory default BIOS settings. You want to modify some specific settings according to the hardware. You want to modify some specific settings to optimize the system performance. How to Use Starting BIOS Setup NOTE: The BIOS Setup Utility screens shown in this chapter are for your reference only.
Main Advanced Security Boot Exit Model: V100 SATA HDD: [INTEL SSDSA2M080G2GC] 80026MB System Time: System Date: [16:33:08] 16 [06/10/2010] Processor Info: Installed System Memory: Intel(R)Core(TM)i7 CPU U640@1.20GHz 4096 MB System BIOS Version: KBC/EC BIOS Version: R1.01 R1.
Key 5-4 Function , Selects a menu title. , Selects an item or option. +/– Changes the value. Enter 1) Brings up the sub-menu when available. 2) Opens or closes the option window when an item is selected. Esc 1) Exits BIOS Setup Utility. 2) Closes the option window if one is open. F1 Provides help information. F9 Loads setup defaults. F10 Saves and exit the BIOS Setup Utility.
Main Menu The Main menu contains the system date and time settings as well as shows the basic configuration of the system. Main Advanced Security Boot Exit Model: V100 SATA HDD: [INTEL SSDSA2M080G2GC] 80026MB System Time: System Date: [16:33:08] 16 [06/10/2010] Processor Info: Installed System Memory: Intel(R)Core(TM)i7 CPU U640@1.20GHz 4096 MB System BIOS Version: KBC/EC BIOS Version: R1.01 R1.
Advanced Menu The Advanced menu contains the advanced settings as shown next.
Turbo Mode sets if turbo memory is enabled. Intel Trusted Execution enables utilization of additional hardware capabilities provided by Intel® Trusted Execution Technology. Intel AMT Setup Prompt sets if the prompt for entering Intel AMT Setup appears during POST. If disabled, you cannot enter Intel AMT Setup. Security Menu The Security menu contains the security settings, which safeguard your system against unauthorized use.
NOTE: You can set the user password only when the supervisor password has been set. If both the administrator and user passwords are set, you can enter any of them for starting up the system and/or entering BIOS Setup. However, the user password only allows you to view/change the settings of certain items. Password on Boot allows you to enable or disable the entering of password for booting up your system.
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. Main Advanced Security Boot Exit Item Specific Help Boot priority order: 1: USB FDC: 2: SATA HDD: INTEL SSDSA2M080G2GC – (S1) 3: USB KEY: 4: USB HDD: 5: LAN BOOT: IBA GE Slot 00C8 v1338 6: 7: 8: Excluded from boot order: : USB CDROM: F1 Help Esc Exit ↑↓ Select Item ←→ Select Menu Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down.
order” list to the “Excluded from boot order” list, and vice versa. Shift+1 Deactivates/activates the highlighted boot device on the “Boot priority order” list. When a device has been deactivated, an “!” (exclamation) symbol appears beside the item and system will bypass it when detecting boot device during POST. Exit Menu The Exit menu displays ways of exiting BIOS Setup Utility. After finishing with your settings, you must save and exit so that the changes can take effect.
Saves Changes saves the changes you have made.
System Recovery Use System Recovery when: Your Windows operating system does not start at all. You want to restore the factory default Windows settings. WARNING: Using this feature will reinstall Windows to your system. All data on the hard disk drive will be lost. To run System Recovery: 1. During system startup when the following screen appears, press Ctrl + Alt + F2 keys for four seconds. 2. The message This will help you reinstall Windows to the whole HDD to factory default.
3. A warning message appears as follows: **************************************** You must accept the following terms before performing the recovery process: 1. The recovery software is solely the purpose of reinstalling or restoring software associated with the hard disk of this operating GETAC machine. 2. Except the above, no other use is granted hereunder. **************************************** (1)Yes, I agree to the provisions of this agreement and wish to continue.
5. After the recovery process has been completed successfully, the GSI (GETAC Smart Installer) screen is displayed at the first boot-up of Windows operating system. 6. GSI will automatically perform system hardware detection and driver installation. After GSI has completed the whole process successfully, system will reboot.
Chapter 6 Installing Software Drivers and Utilities To take full advantage of the unique features of your computer, drivers and utilities must be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers and utilities. If not, you need to install them using the disc supplied with your computer. This chapter describes how to install the drivers and utilities.
How to Use the Driver Disc NOTE: The drivers may have been updated after this manual was published. For driver upgrade, please contact your dealer. This disc supports Windows XP, Windows Vista, and Windows 7. The available items may differ according to your computer model. Some items are for select models only. Do not remove the driver disc when installing the driver. An autorun program is provided on the driver disc to help you easily install the drivers.
Installation for Windows XP After selecting the operating system Windows XP, the driver installation menu appears. To install a driver, just click the particular button and follow the onscreen instructions to complete the installation. Drivers on the First Page Item Description Device Driver Ensures the full function of the other drivers. Install this main driver before installing the other drivers. AHCI Brings up a submenu as shown on the right. Readme Provides information on the AHCI driver.
Item Description vPro Utility Installs the utility that starts the setup and configuration process for an Intel ® vPro system in an enterprise environment. WiFi Installs the WLAN driver/utility for wireless network connection. Touch Screen Installs the touchscreen driver/utility for using the touchscreen feature (select models only). Drivers on the Second Page Item 6-4 Description Digitizer Installs the digitizer driver for using the digitizer feature (select models only).
Item Description GPS Installs the GPS driver for using the GPS feature (select models only). The instructions for installing the GPS driver will appear. GPS Filter Works with the previous item. You must install this driver after installing the above driver to complete the GPS driver installation. Drivers on the Third Page Item Bluetooth Description Installs the Bluetooth driver/utility for using the Bluetooth feature (select models only).
Item WCDMA Description Brings up a submenu as shown on the right. Install the three items for using the 3G feature (select models only). Finger print Installs the driver/utility for using the finger print feature (select models only). Docking Brings up a submenu as shown on the right. Video Capture Installs the video capture driver. USB to COM Installs the USB-to-COM driver. USB to LAN Installs the USB-to-LAN driver. Getac Utility Brings up a submenu as shown on the right.
Item Description V-GPS Installs the V-GPS utility that displays GPS status (select models only). Barcode Reader Installs the Barcode Reader program (select models only).
Installation for Windows Vista After selecting the operating system Windows Vista, the driver installation menu appears. To install a driver, just click the particular button and follow the onscreen instructions to complete the installation. Drivers on the First Page Item 6-8 Description Device Driver Ensures the full function of the other drivers. Install this main driver before installing the other drivers. VGA Installs the VGA driver for full functionality of the video subsystem.
Drivers on the Second Page Item Description vPRO Utility Installs the utility that starts the setup and configuration process for an Intel ® vPro system in an enterprise environment. Digitizer Installs the digitizer driver for using the digitizer feature (select models only). TPM Installs the TPM driver/utility for using the TPM (Trusted Platform Module) support for security. GPS Installs the GPS driver for using the GPS feature (select models only).
Item WCDMA Description Brings up a submenu as shown on the right. Install the three items for using the 3G feature (select models only). Drivers on the Third Page Item Description Smart Card Reader Installs the SmartCard driver for accessing SmartCards (select models only). Bluetooth 6-10 Installs the Bluetooth driver/utility for using the Bluetooth feature (select models only).
Item Description Finger print Installs the driver/utility for using the finger print feature (select models only). Docking Brings up a submenu as shown on the right. Video Capture Installs the video capture driver. USB to COM Installs the USB-to-COM driver. USB to LAN Installs the USB-to-LAN driver. Getac Utility Brings up a submenu as shown on the right. Getac Manager Installs the G-Manager utility that manages and configures various system resources.
performance.
Installation for Windows 7 After selecting the operating system Windows 7, the driver installation menu appears. To install a driver, just click the particular button and follow the onscreen instructions to complete the installation. Drivers on the First Page Item Description Device Driver Ensures the full function of the other drivers. Install this main driver before installing the other drivers. VGA Installs the VGA driver for full functionality of the video subsystem.
Drivers on the Second Page Item Description vPro Utility Installs the utility that starts the setup and configuration process for an Intel ® vPro system in an enterprise environment. Digitizer Installs the digitizer driver for using the digitizer feature (select models only). TPM Installs the TPM driver/utility for using the TPM (Trusted Platform Module) support for security. GPS Installs the GPS driver for using the GPS feature (select models only).
Item WCDMA Description Brings up a submenu as shown on the right. Install the three items for using the 3G feature (select models only). Drivers on the Third Page Item Description Smart Card Reader Installs the SmartCard driver for accessing SmartCards (select models only). Bluetooth Installs the Bluetooth driver/utility for using the Bluetooth feature (select models only). Finger print Installs the driver/utility for using the finger print feature (select models only).
Item Docking Description Brings up a submenu as shown on the right. Video Capture Installs the video capture driver. USB to COM Installs the USB-to-COM driver. USB to LAN Installs the USB-to-LAN driver. Getac Utility Brings up a submenu as shown on the right. Getac Manager Installs the G-Manager utility that manages and configures various system resources. Button Manager Installs the Button Manager utility that can customize your computer’s quick buttons.
Chapter 7 Using Getac Software Getac software is provided for enhanced capabilities and management. This chapter describes how to use the software.
Using G-Manager G-Manager is a unified user interface utility that allows you to manage and configure the following: System Battery ECO (economy mode) Light Sensor Ignition Monitoring GPS Status To start up G-Manager, do one of the following: Click Start All Programs GETAC Utility, or Right-click on the GETAC Utility icon ( click G-Manager. The screen as shown next appears.
For detailed descriptions of G-Manager, click .
Using Button Manager The five quick buttons located on the front of your computer come with predefined functions. You can use Button Manager to re-define the buttons. 1. Click Start Programs Button Manager Button Manager. The following screen appears. 2. Select the button to re-define. 3. Under the Update Button Function click the Key Name dropdown list to select a new button function.
4. Repeat the steps for the other buttons that you want to re-define. 5. Click Save to save your configurations. 6. Click Start Flash to start the flash process, the percentage of flash process will be shown. 7. Click Load the next time you use Button Manager to load any previously saved configurations.
Using Getac Camera (Optional) Getac Camera is a geo-tagging camera program, which allows you to stamp geographical information on photos as watermarks and embed such information into JPEG files as EXIF 2.2 metadata. NOTE: Getac Camera works with Virtual-GPS (a separate application program). Make sure that Virtual-GPS is installed in your computer. Before starting Getac Camera, close any other program that uses the camera; otherwise, Getac Camera can only provide limited functions.
No. Screen Elements Descriptions Preview/Display Displays the live image in Camera mode and the selected image in View mode. GPS Status Indicates if the GPS positioning is completed ( ). or not ( Window Window Control Buttons ) Minimizes the program window. / Resizes/maximizes the program window. When resized, the smaller window size is fixed. You can move it but cannot change the size furthermore. Closes the program.
No. Screen Elements Status Display Descriptions Indicates the use of a feature. GPS Lock in use Front/Bottom camera in use / Night mode in use Continuous/Timer mode in use / Control Buttons Perform immediate tasks on the current image. (See “Camera Controls” and “Viewing Controls” for information.) Watermark Displays the GPS information such as direction, longitude, latitude, GPS status, date, and time. Thumbnail Tray Displays up to 7 pictures in a thumbnail view.
2. For camera settings such as timer, brightness, etc., tap (See “Camera Settings” for detailed information.) . If needed, you can turn on/off GPS lock or watermark using the buttons on the right. (See “Camera Controls” for detailed information.) 3. Aim the camera lens at your subject. Tap and hold the button for focusing. A white plus sign and frame appear. Wait until the subject is in focus. NOTE: The focus button is not available on computer models with 1.3MP camera. 4.
Control Buttons / Descriptions Turns on/off GPS lock. The icon in the button shows the current status. GPS lock allows you record the exact location of the object you are shooting instead of where you are using the computer to shoot the picture. First, put the computer near your object and tap this button to lock the GPS information; then, you can go farther away to where you can have a good view of the object for the shooting.
Method 1: Double tap the thumbnail in the Thumbnail Tray. Method 2: Drag the thumbnail and drop into the preview window. Selecting an Image to View To scroll through the Thumbnail Tray, drag the tray toward the left or right. To select an image to view, use either of the two methods: Method 1: Double tap the thumbnail in the Thumbnail Tray.
Method 2: Drag the thumbnail and drop into the display window. Viewing Controls To Zoom in/out (up to four scales) Via Multi-touch Operations (Select Models Only*) Via Control Buttons / Drag two fingers apart/ towards to zoom in/out. When zoomed in, you can drag to view another portion of the image.
circular motion. * Multi-touch operations are available only on computer models with multi-touch screen and Windows 7. Viewing Image Properties Switch to View Mode, select the image, and tap to view the properties.
Scroll down for more information. To switch back to image view, tap Adding Notes to an Image 1. Switch to View Mode, select the image, and tap 2. In properties view, tap . 3. Type your notes in the entry field. 7-14 Using Getac Software . .
4. When completed, tap . The first three lines of the notes show on the screen. Camera Settings at the bottom of the screen. To change camera settings, tap The Settings window appears showing the setting item previously accessed.
Along the left of the window are all the setting items. You can drag this area up or down to scroll through the items. The middle of the window displays the current item and setting value. To the right is the adjustment bar where you can tap or drag to change the setting value. All changes (except for Camera Mode) remain effective until you change them again.
Incandescence. NOTE: Only one choice (Automatic) is available on computer models with 1.3MP camera. Brightness Adjusts the brightness level. The range of levels depends on computer models. You can tap to restore to the default level. Contrast Adjusts the contrast level. The range of levels depends on computer models. You can tap to restore to the default level. Hue Adjusts the hue level. The range of levels depends on computer models. You can tap to restore to the default level.
Setting Items Name Camera Mode Descriptions Three choices for the shooting mode: Normal This is the default setting whenever the program is started. Continuous Continuous shooting of 3 pictures (1 shot per second). Timer 5-second countdown before shooting. Status Display Turns On (default) or Off the display of the status indicators. Watermark Turns On (default) or Off the display of watermark in the image. (Turning off does not affect the embedded EXIF 2.2 metadata.
Setting Items Name Folder Path Descriptions Sets the storage location of the images. To change to a different folder, tap Browse and select the folder. The default location is User\[user name]\Pictures folder that contains the original images. A subfolder named Thumbs contains a copy of the same images (with filename prefix Thumb_) for the thumbnail view. NOTE: If you are adding or deleting images using File Explorer, make sure to work on both the correct folder and its Thumbs subfolder.
7-20 Using Getac Software
Using Getac Barcode Reader (Optionl) Getac Barcode Reader is a camera-based barcode reading application program. It can identify barcodes of the following types and input the decoded data into any existing processing software. Barcode types supported: 1D – Code 128, Code 39, and EAN family (EAN/JAN-13, EAN/JAN-8, UPC-A, UPC-E) 2D – QR Code NOTE: Recommended for use with the 2.0MP (or higher resolution) camera.
Preview window Toolbar If this is the first time you start the program after it has been installed, the Settings screen instead of the main screen appears. (See “Barcode Reader Settings” for information.) 2. Start your processing software and open a new or existing file. Place the insertion point (or called cursor) where you want the data to be entered.
4. Wait for the program to focus and read the barcode. 5. When the reading is successful, the green indicator lights up. The barcode type and decoded data are shown at the bottom. The Accept and Discard buttons appear. Indicato Barcode information 6. Tap the Accept button for the data to be entered into your processing software. A sound will be played to indicate completion of the entry. Barcode entries are separated by “Enter” (default setting) in the processing software.
Floating button Notepad is shown as an example of the processing software. If you want to discard the data, tap the Discard button. 7. The orange indicator lights up again ready for the next barcode. Repeat the same action for the next entry. 8. To exit the program, tap and hold the floating button and select Exit from the shortcut menu. Toolbar During the operation, you can use the toolbar for functions as described below.
the focus function. This speeds up the process and consumes less power. Hides the screen. To show the screen, tap the floating button . Switches to the Settings screen. Floating Button and Shortcut Menu Whenever the program is started, the floating button appears at the upper right corner of the computer screen. This button provides a quick way to bring up the hidden Barcode Reader main screen. When tapping and holding the button, the shortcut menu appears.
Barcode Reader Settings To set up Barcode Reader, tap in the Barcode Reader main screen or select Settings from the shortcut menu. The Settings screen with three tabs appears.
Tabs Input Setting Items Appending Character Following the Insertion Point Data Entry Method Descriptions Sets how individual barcodes are separated. Enter (default) Each barcode begins in a new line. Tab Barcodes are separated by tabs. None Barcodes are not separated. Sets if the Barcode Reader main screen moves when necessary. Yes (default) The main screen will move aside to keep the latest data input visible. No The main screen remains at the same place unless you manually move it.
Time Lapse Before Entry System Manual (default) Data are entered only upon your request. Auto Data are entered after a specific time lapse (determined by the next item). Sets how many seconds (4, 2, or 1) the program waits before entering the decoded data into the processing software. The default setting is 4. This item is available for setting only when the above item is set to Auto. Camera Switch Switches to the Front (default) or Bottom camera lens.
Chapter 8 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer. This chapter gives you guidelines covering areas such as protecting, storing, cleaning, and traveling.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using an Anti-Virus Strategy You can install a virus-detecting program to monitor potential viruses that could damage your files.
Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft. The cable lock is available in most computer stores. To use the lock, loop the lock cable around a stationary object such as a table. Insert the lock to the Kensington lock hole and turn the key to secure the lock. Store the key in a safe place.
Taking Care of the Computer Location Guidelines For optimal performance, use the computer where the recommended temperature is between 0C (32F) and 55C (131F) – actual operating temperature depending on product specifications. Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. Do not cover or block any ventilation openings on the computer.
using a screen saver or other software that prevents the power management from working. Cleaning Guidelines Never clean the computer with its power on. Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. Dust or grease on the touchpad can affect its sensitivity.
Also, charging will not start if the battery pack is not within the allowed temperature range. It is recommended that you do not charge the battery pack more than once a day. It is recommended that you charge the battery pack with the computer’s power off. To maintain the battery pack’s operating efficiency, store it in a cool dark place removed from the computer and with 30% ~ 40% charge remaining. Important guidelines when using the battery pack.
Use a soft cloth to remove dirt on the display. The touchscreen surface has a special protective coating that prevents dirt from sticking to it. Not using a soft cloth may cause damage to the special protective coating on the touchscreen surface. To remove hard to remove dirt, blow some steam on the particular area and gently wipe away using a soft cloth. Turn off the computer power when cleaning the display. Cleaning the display with the power on may cause improper operation.
When Traveling Before traveling with your computer, make a backup of your hard disk data into flash disks or other storage devices. As an added precaution, bring along an extra copy of your important data. Make sure that the battery pack is fully charged. Make sure that the computer is turned off and the top cover is securely closed. Do not leave objects in between the keyboard and closed display. Disconnect the AC adapter from the computer and take it with you.
Chapter 9 Troubleshooting Computer problems can be caused by hardware, software, or both. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: Try to isolate which part of the computer is causing the problem. Make sure that you turn on all peripheral devices before turning on the computer. If an external device has a problem, make sure that the cable connections are correct and secure. Make sure that the configuration information is properly set in the BIOS Setup program.
Solving Common Problems Battery Problems The battery does not charge (Battery Charge indicator does not light yellow). Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature. Make sure that the battery pack is installed correctly. Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
Make sure that the distance between the two devices are not over 10 meters or that there are no walls or other obstructions between the devices. Make sure that the other device is not in “Hidden” mode. Make sure that both devices are compatible. Display Problems Nothing appears on the screen. During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back. The brightness level might be too low.
Switch the display to the monitor by pressing the Fn+F9 hot key or change the display through the settings in Display Properties. Simultaneous display/multi-display does not work. Make sure that you turn on the external monitor before turning on the computer. Press the Fn+F9 hot key to toggle through the display options or change the settings in Display Properties in Windows. Hardware Device Problems The computer does not recognize a newly installed device.
The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. Keyboard, Mouse, and Touchpad Problems The keyboard does not respond. Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. The numeric keypad is disabled. Make sure that the Num Lock is switched on. (Check if the Num Lock glows or not.) Indicator The external keyboard does not work.
Modem Problems The modem does not work. Make sure that the modem driver is correctly installed. Make sure that the telephone line is properly connected. Make sure that the COM port in the communication software is correctly set. Turn off power management. PC Card Problems The PC card does not work. Make sure that the PC card controller driver is correctly installed. Make sure that the PC card is correctly seated.
If the computer is performing an operation, it normally waits for the operation to finish. The computer does not resume from Standby or Hibernation mode. The computer automatically enters Standby or Hibernation mode when the battery pack is empty. Do any one of the following: Connect the AC adapter to the computer. Replace the empty battery pack with a fully charged one. The computer does not enter Hibernation mode with the Fn+F10 hot keys.
If using an external speaker, make sure that the speaker is properly connected. Distorted sound is produced. Make sure that the volume control is not set too high or too low. In most cases, a high setting can cause the audio electronics to distort the sound. The sound system does not record. Adjust the playback or recording sound levels. The external microphone or audio device does not work. Make sure that the microphone is connected to the proper connector on the computer.
WLAN Problems I cannot use the WLAN feature. Make sure that the mini PCI-E WLAN card is correctly installed. Make sure that the necessary driver(s) is correctly installed. Make sure that the WLAN feature is turned on. Transmission quality is poor. Your computer may be in an out-of-range situation. Move your computer closer to the Access Point or another WLAN device it is associated with. Check if there is high interference around the environment and solve the problem as described next.
Make sure that the Access Point your computer is associated with is powered on and all the LEDs are working properly. If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel. Your computer may be in an out-of-range situation. Move your computer closer to the Access Point it is associated with. Make sure that your computer is configured with the same security option (encryption) to the Access Point.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the computer operation seems to hang up, first wait. It is possible that the computer is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
Appendix A Specifications NOTE: Specifications are subject to change without any prior notice. Parts CPU Memory Specifications Processor Intel® i7-640UM, 1.2GHz, Max. 2.266 GHz with Intel Turbo Boost Technology, Thermal 18W or Intel® i5-540UM, 1.2GHz, Max. 2.
Parts Audio Specifications Features Azalia interface, left/right-channel analog output for line-out connector Speaker One built-in Ports Two audio ports for Line-out (green) / Mic-in (red) Keyboard Standard keys with numeric pad keys, 12 function keys, special Fn (Function) key and Windows keys Water-proof and dust-proof membrane, large character printing, water-proof rubber (option) Pointing device Glide touchpad with 2 buttons, capacitance-type Hard disk drive SATA interface, 5400 rpm support
Parts Specifications Docking 100-pin, engage with vehicle docking Handle Grip and cross-type hand strap Power AC adapter Universal 60 W; input: 100240 V, 50/60 Hz; output: 19 V Battery Li-ion smart 6-cell battery 5200 mAH / 11.1 V (option) Li-ion smart 9-cell battery 7800 mAH / 11.
Appendix B Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
Do not use the adapter if the cord becomes damaged. Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. About the Modem Caution Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
On the Use of the RF Device NOTE: The information in this section applies to models with the wireless LAN module. USA and Canada Safety Requirements and Notices Radio Frequency Interference Requirements and SAR The FCC with its action in ET Docket 93-62 has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC certified equipment. The wireless LAN module meets the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992.
High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a minimum distance of 30 cm (12 inches) or more from the body of all persons. Please contact your professional installer, VAR, or antenna manufacturer for proper installation requirements.
expense. The user is encouraged to try one or more of the following corrective measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency.
Danish Dette produkt er i overensstemmelse med det europæiske direktiv 1999/5/EC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 1999/5/EC. Finnish Tämä tuote noudattaa EU-direktiivin 1999/5/EC määräyksiä. French Ce produit est conforme aux exigences de la Directive Européenne 1999/5/EC. German Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 1999/5/EC. Greek To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας 1999/5/EC.
Local Restrictions of 802.11a/g/n Radio Usage CAUTION: Due to the fact that the frequencies used by 802.11a/g/n wireless LAN devices may not yet be harmonized in all countries, 802.11a/g/n products are designed for use only in specific countries or regions, and is not allowed to be operated in countries or regions other than those of designated use.
03 Allier 41 Loir et Cher 68 Haut Rhin 05 Hautes Alpes 42 Loire 70 Haute Saône 08 Ardennes 45 Loiret 71 Saône et Loire 09 Ariège 50 Manche 75 Paris 11 Aude 55 Meuse 82 Tarn et Garonne 12 Aveyron 58 Nièvre 84 Vaucluse 16 Charente 59 Nord 88 Vosges 24 Dordogne 60 Oise 89 Yonne 25 Doubs 61 Orne 90 Territoire de Belfort 26 Drôme 63 Puy du Dôme 94 Val de Marne 32 Gers 64 Pyrénées Atlantique Departments in Which the Wireless LAN Module’s Maximum EIRP
