User's Manual
Table Of Contents
- 1. General description
- 2. Features and benefits
- 3. Quick reference data
- 4. Ordering information
- 5. Block diagram
- 6. Pinning information
- 7. Limiting values
- 8. Recommended operating conditions
- 9. Thermal characteristics
- 10. Characteristics
- 10.1 Power management characteristics
- 10.2 Antenna presence self test thresholds
- 10.3 Typical 27.12 MHz Crystal requirements
- 10.4 Pin characteristics for 27.12 MHz XTAL Oscillator (OSCIN, OSCOUT)
- 10.5 RSTPD_N input pin characteristics
- 10.6 Input pin characteristics for I0, I1 and TESTEN
- 10.7 RSTOUT_N output pin characteristics
- 10.8 Input/output characteristics for pin P70_IRQ
- 10.9 Input/output pin characteristics for P30 / UART_RX, P31 / UART_TX, P32_INT0, P33_INT1
- 10.10 Input/output pin characteristics for P35
- 10.11 Input/output pin characteristics for DP and DM
- 10.12 Input pin characteristics for SCL
- 10.13 Input/output pin characteristics for SDA
- 10.14 Output pin characteristics for DELATT
- 10.15 Input pin characteristics for SIGIN
- 10.16 Output pin characteristics for SIGOUT
- 10.17 Input/output pin characteristics for P34
- 10.18 Output pin characteristics for LOADMOD
- 10.19 Input pin characteristics for RX
- 10.20 Output pin characteristics for AUX1/AUX2
- 10.21 Output pin characteristics for TX1/TX2
- 10.22 System reset timing
- 10.23 Timing for the I2C-bus interface
- 10.24 Temperature sensor
- 11. Application information
- 12. Abbreviations
- 13. Revision history
- 14. Legal information
- 15. Contact information
- 16. Tables
- 17. Figures
- 18. Contents
![](/manual/getac-technology/pr533a/user-s-manual-english/images/img-2.png)
PR533_SDS All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2014. All rights reserved.
Product short data sheet
COMPANY PUBLIC
Rev. 3.6 — 27 October 2014
206436 2 of 36
NXP Semiconductors
PR533
USB NFC integrated reader solution
Support of USB 2.0 full speed, interoperable with USB 3.0 hubs.
The PR533C3HN in PCD mode is compliant with EMV contactless specification V2.0.1.
1.4 Supported operating systems
• Microsoft Windows 2000
• Microsoft Windows XP (32 and 64 bits)
• Microsoft Windows 2003 Server (32 and 64 bits)
• Microsoft Windows 2008 Server (32 and 64 bits)
• Microsoft Windows Vista (32 and 64 bits)
• Microsoft Windows 7 (32 and 64 bits)
The PR533 is supported by the following OS through the PCSC-Lite driver:
• GNU/Linux using libusb 1.0.x and later
• Mac OS Leopard (1.5.6 and newer)
• Mac OS Snow Leopard (1.6.X)
• Solaris
• FreeBSD
2. Features and benefits
USB 2.0 full speed host interface and CCID protocol support
Integrated microcontroller implements high-level RF protocols
Buffered output drivers to connect an antenna with minimum number of external
components
Integrated RF level detector
Integrated data mode detector
Supports ISO/IEC 14443A Reader/Writer mode up to 848 kbit/s
Supports ISO/IEC 14443B Reader/Writer mode up to 848 kbit/s
Supports contactless communication according to the FeliCa protocol at 212 kbit/s and
424 kbit/s
Supports MIFARE encryption
Typical operating distance in Read/Write mode for communication to
ISO/IEC 14443A/MIFARE, ISO/IEC 14443B or FeliCa cards up to 50 mm depending
on antenna size and tuning
I
2
C-bus master interface allows to connect an external I
2
C EEPROM for configuration
data storage or to control a TDA8029 contact smart card reader
Low-power modes
Hard power-down mode
Soft power-down mode
Only one external oscillator required (27.12 MHz Crystal oscillator)
Power modes
USB bus power mode
2.5 V to 3.6 V power supply operating range in non-USB bus power mode