HANVON PENTECH CO., LTD TO： TECHNICAL SPECIFICATION Name：10.1 Inch EM Touch Board MODEL NO.: TP-101S01-H1S1-GT Material Code：810011234 The content of this information is subject to be changed without notice. Please contact HANVON or its agent for further information. □ Customer’s Confirmation By Date □ HANVON’s Confirmation APPROVED CHECKED CHECKED DESIGNED The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD Revision History Rev. 1.0 Issued Date 2016-6-8 Revised Contents Preliminary The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD TECHNICAL SPECIFICATION CONTENTS 1. Scope .............................................................................................................................. 4 2. Features ......................................................................................................................... 4 3. General Specifications ................................................................................................. 4 4. Appearance.........................................
HANVON PENTECH CO., LTD 1. Scope This specification is applicable to Hanvon PenTech Electromagnetic Touch Board designed. 2. Features Without affecting the screen display High screen resolution High pressure levels High position accuracy Low power consumption Commercial temperature range Support battery-free, cordless and pressure sensitive pens 3. General Specifications Parameter Sensor Board Specifications Unit Note External Dimension 256.73(L)×114.35(W ) ×3.2(H) mm ±0.
HANVON PENTECH CO., LTD Others Module Weight g TBD Note: 1、This specification is for standard module. For better performance, it needs to be customized by customer’s system. 2、Maximum different error in pressure values < 2LSB 3、Maximum Coordinate jitters < 1 point The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD 4. Appearance The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD 5. Mechanical Drawing The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD 6. Signal Assignment NO. 1 2 3 4 5 6 7 8 J1(USB) NC USBUSB+ PDCT SLEEP NC VCC+3.3V GND Note: 1 Logic Low: 0 < UL < 0.2×VDD; Logic High: VDD-0.3 < UH < VDD. The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD 7. Electrical Characteristics Parameter Ground Digital Power Supply Symbol GND VDD IVcc Sleep Power SLP Reset Time RST Sleep Time SLP Awake Time SLP Power Cycle - Conditions Min. Vcc=3.3V 20 SLP = ‘1’; 0.10 Vcc=3.3V I = 10mA 50 SLP = ‘1’; 10 Vcc=3.3V SLP = ‘0’; 15 Vcc=3.3V Vcc=3.3V 50 Typ. 0 3.3 40 Max. Unit V V 60 mA 0.33 0.70 mW 70 100 ms 20 50 ms 20 50 ms 100 150 ms The information contained herein is the exclusive property of Hanvon Pentech Co.
HANVON PENTECH CO., LTD 8. Idle Mode* If the board does not find the pen in 5 seconds, the board enters idle mode (Max. current < 20mA), Support selective suspend mode, followed WHQL 8.0/8.1 Note: The power consumption in Idle mode and performance need to be defined after the joint debugging. 9. Block Diagram Sensor board Control Board 8 Pin Connector The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD 10. Pen Accuracy Δ Rpen=0.9mm Figure 1 Rpen and Δ Pen θ θ Y Ф LCD X Figure 2 Ф = 90°, θ = 15°：Δ ≤ 0.5mm Note 1: If noise exists, Δ will increase. Note 2: At the edge of the sensor board, Δ≤ 0.8mm. Note 3: Writing angle(Ф) must be greater than 40 degrees. The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co.
HANVON PENTECH CO., LTD Figure 3 Center/Edge of the sensor board The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
HANVON PENTECH CO., LTD 11. Reliability test （ This is for your reference only. The final Reliability test for TP-101S01-H1S1-GT will be provided after we get final product） Test Conditions: 1. The Electromagnetic Touch Board should be inspected as regular functional testing. 2. No condensing of water (moisture) is allowed on the Electromagnetic Touch Board. 3. For environmental tests, temperature gradient is 15℃/hour. 4. The number for the test samples is 10 units.
HANVON PENTECH CO., LTD 12. Labels 12.1 Green Label Label Material: White color Label Ink: Green Label Location: Paste on the middle of the board backside 12.2 Bar Code Label 12.3 Shipping Mark Label TBD 13. Packing TBD The information contained herein is the exclusive property of Hanvon Pentech Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Hanvon Pentech Co., Ltd.
