CONTENT
Valued Customer, Thank you for purchasing our top-quality GEWA G9 Drum Workstation! The G9 drum workstation is an E-Drum that gives you a highly impressive sound and playing experience, while offering a huge extra set of additional and easy to use sounds and features. Your safety is very important to us! So please read the safety information carefully and take good note of the given information.
Electric Hazard WARNING • • • • • • • • • • • • Do not expose the apparatus to dripping or splashing. Do not place objects filled with liquids, such as vases or glasses on or near the apparatus. The mains plug shall remain readily operable. Never use damaged power supplies/cords. Install power supplies/cables firmly to avoid the risk of damage. Even low electric currents can lead to serious injuries and even death! Never open the drum console. Never insert water or liquids into the drum console.
1.3 PROPER HANDLING • • • • • 1.4 Please keep your digital drum console in a dry environment. Audio accessories for audio playback (connected to the in- or output of the console) or for data communication can be connected. Accessories must match the relevant technical specifications (see section 16, Technical Data) Only and always use GEWA certified power adapters, and make sure that they are properly attached and connected.
1.5 CE LABEL Your GEWA G9 Drum Console complies with the requirements of the EU directives: Directive 2014/53/EU Standards to which conformity is declared: EN55020:2007+A11:2011 EN55024:2010 EN55032:2012 EN61000-3-2:2014 EN61000-3-3:2013 EN301489-17:V3.2.0 EN60065:2014 EN62311:2008 2009/125/EC: 2009 (EC Regulation 1275/2008 + 801/2013) EN300328:V2.1.1 EN301893:V2.1.1 Compliance with the above directives is confirmed by the CE label on the device.
1.6 FCC LABEL/FCC MARK This product is certified by the Federal Communications Commission (FCC) and is identifiable by its FCC-ID: 2APTV-GEWAG9. It contains a modular approved transmitter module with FCC-ID: A8TBM64S2. This information is also shown on the permanent label at the bottom side of each device. The built-in Wireless LAN module is only a DFS Client and is not capable of performing Dynamic Frequency Selection (DFS) itself.
1.7 REGULATORY INFORMATION - CANADA ENGLISH This product is certified by Innovation, Science and Economic Development (ISED) and is identifiable by IC: 23946-GEWAG9. It contains a modular approved transmitter module with IC: 12246A-BM64S2 as well as license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). ICES-003 Class B Notice This Class B digital device complies with Canadian CAN ICES-003.
FRANÇAIS Ce produit est certifié par Innovation, Sciences et Développement Économique (ISDE) et est identifiable par IC: 23946-GEWAG9. Il contient un module d’émetteur approuvé avec IC: 12246A-BM64S2 ainsi que des émetteur(s)/récepteurs(s) exempts de licence qui sont conformes aux CNRs applicables de Innovation, Sciences et Développement économique Canada. Avis NMB-003, Classe B Le présent appareil numérique de la classe B est conforme à la norme NMB-003 d'Industrie Canada.
1.8 RECYCLING In case your digital drum console needs to be disposed, take it to your local community waste management service location n (e.g. disposal companies, recycling centers). The displayed symbol requires that devices labeled with this symbol must be disposed separately from household waste. Under the Electrical and Electronic Equipment Act, owners of devices marked with this symbol are required by federal law to deposit waste electrical and electronic equipment in a separate waste collection.
2 PARTS SUPPLIED WITH THE GEWA G9 The G9 in original packaging contains the following items.
3 ASSEMBLY INSTRUCTIONS 3.1 MOUNT BRACKET ASSEMBLY 3.2 CONNECT YOUR EQUIPMENT TO THE C ONSOLE 3.2.
3.2.2 REAR PANEL Make sure the power is OFF when connecting the drum module with external devices.
3.2.3 3.2.3.1 CYMBALS GEWA C YMBALS GEWA Cymbals are equipped with two Stereo jacks (6,35 mm - 1/4” TRRS standard). In conjunction with GEWA modules only the jack closest to the middle hole of the cymbal is relevant. 3.2.3.
Connecting other Cymbals Cymbal Type Components Components Trigger Type (Trigger Settings) Single Zone Cymbals Edge Not Used Single/Dual 2-Zone Cymbals Bow|Edge Not Used Dual 3-Zone Cymbals without extra Bell output Bow|Edge|Bell Not Used Dual 3-Zone Cymbals with extra Bell output Bow|Edge Bell 3Way Hint 3.2.3.3 Different cymbal types will only work in conjunction with the matching Trigger Type. For more information please refer to section 11.3.2.3 Trigger Type on page 95.
4 EXPLANATION OF HARDWARE FUNCTIONS The functionality of the physical dials and buttons can vary depending on the state of user interface (software). Some buttons are customizable. This section describes the standard functionalities when starting the device.
5 STARTING THE DEVICE Connect the DC plug of the AC power adaptor to the DC IN jack on the rear panel. Connect the mains plug to the electrical outlet. With the cord connected correctly the [Power] button lights up in red. The device is in standby mode and ready to be explored. Press the [Power] button to boot the apparatus. Wait for the device to boot Note: In order to save energy, the G9 provides an “Auto Power” feature.
6 BEFORE YOU START…. This section gives a brief introduction to important global settings of your G9 Drum Workstation. 6.1 TRIGGER SETUP Your GEWA Drum Console provides trigger presets for different pad configurations available.
6.2 BLUETOOTH, WI-FI AND AUTO OFF Access the wireless options and shut down timer in General Settings.
7 USER INTERFACE - BASICS This section covers general aspects of using the G9 Drum Workstation. You will learn how to work with physical and digital Dials, learn about the Interface Structure and gain a fundamental understanding of using the built in Touch Screen. Please choose a topic from the submenu in this section. 7.
To do so proceed as follows: 1. 2. 3. Tap the [Advanced] button. Go to: General Settings ➔ Module 4 ➔ Device ➔ Start Screen Uncheck “Easy Mode” Hint: Unchecking “Easy Mode” will affect the start screen as well as the functionality of the [Home] button. 7.3 WORKING WITH DIALS To get started push the [Red Dial] once to access the Easy Mode screen. In addition to the touch screen, we have added physical dials for key functions, which are located on the left-hand side of the screen.
Please note that in the Trigger Settings mode the gray dials change function to Head Gain, Head Threshold and High Level, but still function in the same fashion as presented by the example of the Master volume. 7.4 INTERFACE STRUCTURE The G9 is divided into several sections called Modes. By default, the console starts in Easy Mode. You can enter the Advanced Modes with a single tap on the [Advanced] button in the right bottom corner.
7.5 TOUCH SCREEN Many selections can be made utilizing the intuitive touch screen, such as finger dragging motions, number pad- and selection drop downs which can be accessed by tapping once. Fields with drop down menus have a little Flag ( ) attached to the right-hand side of their frames. When visible, [+] and [-] buttons allow for cycling through the underlying menu (One entry per tap). The cross in the upper right-hand corner serves as an alternative for closing dialogues.
Basic Keyboard Functions Description Single Tap Double Tap Lower case Lower case Caps lock on Upper case Next letter as Upper case --- Caps lock on Upper Case (Caps Lock On) --- Delete Delete letter in front of the cursor --- Confirm Confirm and close keyboard ---
8 PERFORMANCE The Performance Mode contains all key functions that center around actually playing drums. You will stay in this mode most of the time during your daily practice routine. This mode provides a metronome and a song player to help you master difficult exercises and songs. Here, we assume working trigger settings as well as finalized drum kits and presets. Choose your drum kit and decide whether you want to be accompanied by a song, metronome or both. 8.1 MODULE 1 8.1.
Drum Kit Number 8.1.1.1 M ANAGING D RUM K ITS (P RESETS ) Tapping the [Drumkit Field] opens the Drum Kit Browser which provides a palette of functions to manage your drumkit library including the drum kit export.
that the referenced sound samples are installed, whether they are factory sounds or sounds downloaded from the Sound Store. Missing sounds in the importing device will result in empty Sound Select fields in Kit Editor ➔ Module 2 ➔ Instrument Select.
How it works: For each input channel, detected MIDI velocity values are returned as values of a color scale from (0) to (127). The actual color values might vary depending on the chosen UI Theme. Deviations from the normal color scheme only occur regarding different types of color blindness. The regular appearance of gradients is then replaced by a scheme out of the perceivable color spectrum of the concerned group of people. See the table below for color scales by UI Theme.
8.2.1.3 S NARE S TYLE (R IMSHOT , C ROSSTICK AND X-F ADE ) Here you can quickly set the rim sound, to either Rimshot, Crosstick or X-Fade. X-fade is a dynamically driven switch which returns either rimshot or cross stick depending on the velocity of the stroke. If you select x-fade, the dial of the same name activates and enables you to adjust the threshold for the dynamics of the cross stick before it turns into a rimshot. Tap on the [X-Fade dial] to activate the fader.
Song Player – Supported File Formats Icon 8.3.1.1 Ext. Description Developer *.aif Audio Interchange File Apple Inc *.flac Free Lossless Audio Codec Xiph.Org Foundation *.m4a MPEG 4 Audio International Organization for Standardization (ISO) *.mp3 MPEG Layer III Moving Picture Experts Group *.ogg Developers´ Project Name Xiph.Org Foundation *.wav Waveform Audio File Microsoft & IBM *.
G9 File Select Browser (Audio) File Select Intern USB Filter Search Title 1 in mp3 format.mp3 Title 2 in mp3 format.mp3 Title 3 in mp3 format.mp3 SYSTEM/ Title 4 in mp3 format.mp3 DrumKits Title 5 in m4a format.m4a Firmware Manuals Title 6 in wav format.wav QuickRecord Open this Audio file by double tapping.mp3 Title 8 in mp3 format.mp3 Sorted by Name Date Type The left column displays all folders in the open directory, the right column lists all contained files.
8.3.1.2 S ONG P LAYER F EATURES With an audio file loaded you have access to a selected palette of functions that are designed to accompany songs with the instrument as well as improving your practice routine.
8.3.1.2.2 P LAY M ODES The Song Player offers three different Play Modes: Play Modes Play once Loop active song Loop folder To select a play mode, tap once on the corresponding icon. 8.3.1.2.3 E XTERNAL S ONG P LAYERS Other options for choosing songs are by connecting your phone with either Bluetooth or the MIX IN port in the back of the console. In this case the loop function is not available, and you use the control functions of the external player instead.
System Folders in File Manager INTERNAL SD/SYSTEM/ Drumkits Firmware Manuals QuickRecord Custom User Folder with content Copied Song in m4a Format.m4a Flac Audio File.flac 8.3.1.2.6 V ARI S PEED The Tempo of the song playing can be altered by using the Vari Speed function. Tap once on the [Vari Speed] dial and adjust the speed by dragging the fader up or down. The slider allows for speeding up or slowing down by 50% compared to the recorded tempo.
Adjusting the Metronome Tempo Number Pad Hardware Dial Software Dial Fader Tap Button Metronome Metronome Tempo Tempo 0 Allegro 120 bpm bpm 120 bpm Gestures Tap Turn Tap Drag Tap Buttons Metronome Tap periodically to set tempo Start/Stop You can also control the Time Signature, the Interval and the Click Volume. Tap once on the respective field to call up the option wheels and faders. A [Mute] button turns off the metronome sound without changing settings made in module 4.
Tip: The visual mode is designed to be vertically free floating. Place a finger the top of the pop-up, hold down, and drag the box up or down into its desired position. It is the only pop-up that won´t close automatically when leaving the performance mode. As a practice tool it is considered to always stay in front. You can only close it manually by tapping on [x] in the upper right-hand corner. 8.4.
1. Touch the field [Tap Channel]. Tap Channel Aux 2 2. Select a pad from the drop down by double tapping. 3. Specify the desired pad component by checking one or both boxes below the Tap Channel field (Pad or Rim etc.). All functions on the right-hand side of the Tap Channel field are identical with those in the function set Metronome. Thus, make sure that Tap is set to “on” and Click Volume is not muted.
9 KIT EDITOR In the Kit Editor mode, you can modify the current drum kit presets, such as changing the individual pad sounds, tuning of drums and adding effects. Furthermore, it is possible add equalization and compressors to the sound of each pad. Instead of changing all the pads together with the Drum Kit selector, you can customize each pad to the desired sound qualities. Use the presets provided as a starting point.
9.1.1.1 I NPUT C HANNELS The Pad order from left to right matches the order of Trigger Inputs of the rear panel. Select a connected pad by tapping the tile above the pad name. A selected pad is highlighted by a surrounding frame. Peak Input Kick Snare Tom 1 Tom 2 Tom 3 Tom 4 Ride Hi-Hat Crash1 Crash2 Aux 1 Aux 2 Aux 3 Aux 4 G9 Ports – Input Channels The Peak row remembers the highest Velocity value detected while playing and for each pad separately.
9.1.1.3 P EAK D ETECTION With this function you can reset the peak monitor of the active module to the color value assigned to the velocity level of 0. This is especially important to check if altered trigger parameters work as desired. Tapping [Reset] refreshes the Peak Monitor and deletes the detection history. 9.2 MODULE 2 9.2.1 9.2.1.1 INSTRUMENT SELECT D RUM K IT The Drum Kit field is the starting point for any activity regarding sound design and trigger settings.
9.2.1.2 P AD C OMPONENTS The pad component icons are located on the right-hand Pad Component Icons side of module 2. You can tap on an icon to activate the Drums component, giving access to its parameters in module 3. Head Rim X-Stick The appearance of the icons and their naming depends on the Trigger Bank assigned. Assigning a cymbal trigger bank will display Bow/Bell/Edge icons and cymbal parameters in module 3, even though the corresponding input channel is labeled as e.g. Snare.
9.2.1.4 S OUND B ROWSER – P ROPERTIES The sound browser lists all installed sounds by instrument categories, which are represented by the tabs shown on top of each sound list. By default, list entries are sorted by ascending internal sound numbers of the active instrument category (tab). This ordering can be changed by checking one of the options available under “Sorted by”.
With sound grouping the user can pick all matching component sample sets of a recorded instrument at the same time and assign it to an input channel, regardless which component icon is active. How it works: In the Sound Browser list entry names end with a suffix indicating the type of component sample. Regarding cymbal samples Suffix and component name are identical and selecting one component sample will select all other matching sample sets automatically.
G9 Sound Browser Sound Browser Sorted by Instrument Category Kick Drums Snare Drums Toms Ride Cymbals Crash Cymbals Hi-Hats Cymbals SFX Percussion 1 Percussion 2 Sounds SFX Source Number Instrument Cat 001 14” Collectors Maple C AC 002 14” Collectors Maple S AC 003 14” Collectors Maple CS AC 004 14” Collectors Maple Rim AC 005 14” Collectors Maple X-Stick AC 006 14” US Vintage C AC 007 14” US Vintage S AC 008 14” US Vintage CS AC 009 14” US Vintage Rim AC 010 14”
9.2.1.5 D RUM K IT P RESETS - P ARAMETERS Drum Kit Presets store values of all parameters associated with a recorded drum set. In the G9 interface, accessible drum kit parameters are spread over several thematically divided modes: Performance, Kit Editor and Effects. Every change in one of the relevant parameters will potentially require saving the active drum kit or creating a new one using the Drum Kit Browser, otherwise edits will be discarded as soon as you change the kit.
Drum Kit Parameters -Complete List Mode Parameter Values Direct (Custom) Preset (Indirect) Performance Snare Style – all related parameters ● Mixer – Volume Faders ● All sound referencing per channel ● Pad Midi Settings ● All Mix/ Effect Sends parameters ● All Sound Edit parameters ● All Second Sound parameters ● All Hi-Hat Volume parameters ● Pad EQ - On/Off Switch ● Pad EQ - All curve parameters ● Pad Compressor- On/Off switch ● All Compressor parameters ● On/Off Switch express
A detailed explanation of each parameter will follow in the respective modes. The following sub section assumes parameter values to be set and tackles the preset management of Drum kits such as the creation of new kits or the exchange of drum kit presets between different G9 devices. 9.2.1.6 P RESET M ANAGEMENT - E LEMENTS The parameters presented above form a Drum Kit preset, which can be saved as an individual user Drum kit. The G9 provides a variety of features to handle these presets.
The bottom section of the Drum Kit Browser hosts the Feature Shelf which contains all preset management options. The number of options varies depending on the type of preset. The G9 distinguishes between user presets and factory presets. Factory presets cannot be edited or deleted; therefore, the palette of options is restricted.
9.2.1.6.3 R ENAME D RUM KITS Renaming a drum kit will affect the preset name only and retain individual parameter values. This option is not available for factory drum kits. 1. 2. 3. 4. 5. Tap the [Drum Kit] name field. Tap once on a user drum kit in the drop-down list. Tap [Rename] in the Feature Shelf. Enter a name for the new preset using the keyboard. Confirm by tapping [OK]. 9.2.1.6.4 D ELETING D RUM K ITS Proceed as follows: 1. 2. 3. 9.2.1.7 Tap the [Drum Kit] name field.
9.2.1.7.1 E XPORT The export of a drum kit is straight forward. Tapping the [Export] icon in the feature shelf will store a copy of the drum kit in the default export folder on the internal SD Card. The corresponding directory path is: INTERNAL SD/SYSTEM/DrumKits System Folders in File Manager INTERNAL SD/SYSTEM/ Drumkits Firmware Manuals QuickRecord Custom User Folder with content Copied Song in m4a Format.m4a Flac Audio File.
9.2.1.7.2 I MPORT G9 Drum Kit Import Browser Drum Kit Import Import Settings INTERNAL SD/SYSTEM/DrumKits/ Filter Exported Drum Kit File Name GEWA Drum Kits (*.gdk) Exported Drum Kit File Name Exported Drum Kit Highlighted Custom Import Name Exported Drum Kit File Name Exported Drum Kit Highlighted Exported Drum Kit File Name Exported Drum Kit File Name Exported Drum Kit File Name Import Close The import is possible via USB or from the internal SD Card.
Task Bar – Drum Kit Import Internal SD Card (opens root directory) External USB device (opens root directory) Go to root directory of the active path. Move up one level in the folder hierarchy Search Import Imports highlighted Kit into the Drum Kit Browser. Close Closes the import dialogue (returns to Drum Kit Browser). Characteristics using Search Step 4 offers the option of using the search function as an alternative to the linear path navigation.
Ports – MIDI OUT MIDI OUT (analog) USB OUT (digital) An example when a deviation from the internal key assignments of the G9 might be necessary is the fact that some manufacturers use a shifted key setup internally (e.g. assignment starts at a different octave of the keyboard). To make these devices compatible with each other, one them needs to change its external key assignment, otherwise the units would address other programs than the intended.
9.3.1.3 E FFECTS The dials Ambient, Instrument Reverb, Room Reverb and Multi Effects allow for gradually dialing in settings made in the Effects mode. As an instance, these sliders are exact representations of the corresponding pad slider in the FX Send mixer of the Effects module. On the right-hand side, you can turn on or mute the corresponding module in the Effects mode. Tap on the corresponding software dial and increase the amount of an effect by dragging the slider up.
The following illustration shows how Tuning Coarse and Tuning Fine interlock giving full access to the full 2-octave spectrum in increments of one cent. Tuning up by 50 cents results in the same pitch as tuning down by 50 cents from the next higher semi tone: Tuning Coarse and Tuning Fine – Fader Positions Tuning Coarse Tuning Fine 1.00 +1 Semi Tone Frequency 0.50 0.00 Semi Tone Frequency 0 1.00 0.50 0.
multiplier curve is a dynamic combination of a hold feature (multiplier = 1) and the tail with decreasing factors for longer time frames. This complex relationship is fixed and not editable in its parameters. The illustration above gives an idea, how the Release feature shapes the amplitude of a sample in relation to the fader position. Curves shown are optimized for visualization purposes and don´t claim to be exact. 9.3.
G9 Sound Browser Sound Browser Sorted by Instrument Category Kick Drums Snare Drums Toms Ride Cymbals Crash Cymbals Hi-Hats Cymbals SFX Percussion 1 Percussion 2 Sounds SFX Number Instrument Cat 001 14” Collectors Maple C AC 002 14” Collectors Maple S AC 003 14” Collectors Maple CS AC 004 14” Collectors Maple Rim AC 005 14” Collectors Maple X-Stick AC 006 14” US Vintage C AC 007 14” US Vintage S AC 008 14” US Vintage CS AC 009 14” US Vintage Rim AC 010 14” US Vint
9.3.4 HI-HAT VOLUME CONTROL This function set allows for adjusting the volume of different Hi-Hat components relative to each other.
A selection of factory presets is provided to enhance your sound without deep knowledge in sound engineering. Load a preset and see how it affects the sound and the curve shapes of equalizer and compressor in module 4.
Since the functioning of pad equalizers and pad compressors is identical with those available for the main stereo outputs (Master, Monitor and Headphones), we will focus on these features in General Settings mode. (Please refer to section 12.2.1.1 Equalizer on page 113 and 12.2.1.
10 EFFECTS The G9 is equipped with 4 different effect modules. Ambience hosts environmental sampling from Funkhaus Studios Berlin. Instrument Reverb and Room Reverb are two modules addressing traditional, generic types of reverb. Under the Multi Effects part of this mode you can control any effect that is not room simulation or reverb. Examples are echo effects or frequency modulation.
Drum Kit Parameters -Effects Mode Direct (Custom) Parameter Values Preset (Indirect) Effects On/Off Switch expression ● FX Send Level Faders ● Level ● Pre-Delay (Ambience) ● Gate Threshold (Instrument Reverb) ● Send to Room Reverb (Multi FX) ● Every other FX 2-4 parameter |…| ● ● Any change in value of one or more of the parameters shown above will cause the drum kit name to update. A preceding asterisk (*) will be added to the drum kit name in all Drum Kit fields in the user interface.
FX Sends 4 Multi Effects Send Levels / FX 4 Tom Grouping -12 dB Kick Cymbal Grouping -12 dB Snare -12 dB Tom 1 -12 dB Tom 2 -12 dB Tom 3 -12 dB Tom 4 -12 dB Ride -12 dB Hi-Hat -12 dB Crash1 -12 dB Crash2 Dry Dry Dry Dry Dry Dry Dry Dry Dry -12 dB Aux 1 -12 dB Aux 2 -12 dB Aux 3 -12 dB Aux 4 Dry Dry Dry Signal Dry Dry Dry Hint: The default factory setting for FX Send sliders is -12 dB (centered).
with a saved preset you have the chance to repeat the steps of loading the preset and saving the kit. Choose b) if you just want to save the kit as it is including all effect parameter values. In this case it is recommended saving a new drum kit to avoid overwriting other presets. When choosing this option, you can still save out the effect parameters as a preset later.
Preset Management -Feature Shelf Function Preset Type Load Save Rename New Delete Factory Preset User Preset 10.4.1 LOADING PRESETS Proceed as follows: 1. Tap on the [Preset] field. 2. Tap once on the preset you want to load. 3. Tap [Load] in the Feature Shelf. The dialog closes automatically, and the new preset is active. Save the drum kit to permanently connect the preset with the kit. 10.4.
If you choose direct storage of parameter values proceed as follows: 1. Go to either Performance ➔ Module 1 ➔ Drum Kit or Kit Editor ➔ Module 2 ➔ Instrument Select ➔ Drum Kit 2. 3. 4. 10.4.4 An asterisk (*) before the kit name indicates changes in directly storable values. Tap the [Drum Kit] name field to open the Drum Kit Browser. Choose one of the following options: a. Overwrite an existing kit by selecting its name in the list and tapping [Save]. b.
10.5 10.5.1 MODULE 1 FX1 AMBIENCE SAMPLES The Ambience module hosts room samples taken in Funkhaus Studios. Since a room responds to moving air in a characteristic and consistent manner, the possibilities of parameters are limited by the nature of the effect. Ambience controls the time until the sound bounces off an obstacle resulting in an echo. The effect is designed to affect the sound of the kit globally, which follows the assumption that the whole kit is set up in the same room or environment.
belongs to Instrument Reverb exclusively. Factory presets provided for Instrument Reverb focus on instrument specific effects but derive their characteristics from the same parameters and value ranges. 10.6.1.1 R EVERB T YPES AND P ARAMETERS The following reverb types and parameters are available: Reverb Types (Instrument and Room) Plate1 Small Plates produce a mechanically generated reverb without early reflections. This is a simulation of a smaller size plate with a certain characteristic.
Reverb Types - Parameters Parameters Description Value Range Storage Direct (Custom) Indirect (Preset) on/off ● Pre-Delay The amount of time before the onset of reverb. Longer delays leave the dry sound untouched in its attack and preserve clarity of the sound. Short delays blend with dry signals earlier at the cost of crispness, if reverb starts before the fully developed attack of the dry sound. 0 - 250ms ● ● Reverb Time Controls the length of the reverb after Pre-Delay.
Since the functioning of this effect section is identical with the module Instrument Reverb, please refer to the previous section for delineation of concepts, explanation of reverb types and parameters. 10.8 MODULE 4 10.8.1 FX 4 MULTI EFFECTS Effects in this module comprise everything that is not associated with Ambience, Instrument Reverb or Room Reverb as for example frequency modulation. Results are obtained by using algorithms to create a certain effect.
Wah-Wah The Wah-Wah effect is created by dynamically “brushing” through the frequency spectrum of the dry signal utilizing a specific audio filter. Instead of the classic pedal control, the G9 uses the Velocity of the stroke to control the movement of the filter along the frequency spectrum. Parameters Range Filter Type Low Pass, Band Pass Frequency 100Hz - 8kHz Unit Dry/Wet Description Choose between a High Cut (Low Pass) or a Band Pass Bell filter.
Distortion / Saturation Overloads the audio signal with gain and adds additional harmonic frequencies to the mix, resulting in a fuller but in case of distortion also edgier sound. This method is prone to scaling up frequency amplitudes along the frequency spectrum, with the result, that the amplitude would surpass 0 dB at more and more frequencies. Consequently, audio Clipping is forced to generate the effect of added harmonics in the audio mix.
Flanger Doubles the dry signal and displaces it within a short delay time, so that dry signal and duplicate are not perceived as 2 distinct sounds. Compared to similar effects, Flangers delay the duplicate signal slightly more than traditional Phaser effects and Flangers accept feedback signals to process the modulation, resulting in an effect similar to the sound of a jet plane. Flangers use cone filtering for the frequency modulation of the duplicate signal.
Auto Pan Pans the sound between the left and the right speaker in 180° out of phase. The volume of both channels (Left and right) is driven by a sine LFO waveform. Parameters Modulation Rate Modulation Depth Range Unit 0-20 Hz Dry/Wet Description Controls the length of the LFO waveform period and thus the frequency of the alternating effect. Controls the intensity of the panning effect. Values range from 0 (equals Mono) to 127 (full alternation between 63L and 63R values).
Delay Records a segment of the played sound and plays it back repeatedly (multi-echo). Parameters FX Type Range Unit Dry/Wet Description Mono creates a mono signal audible on both speakers simultaneously. In stereo mode the delayed signals alter between the left and the right speaker. The Mono signal is moved to the left speaker and the second signal for the stereo effect is inserted in between the Mono signal on the opposite speaker.
11 TRIGGER SETTINGS In the Trigger Settings mode, you can adjust the behavior of the sensors in the pads further customizing the e-drum. Note that the top three dials on the left-hand side change to affect the High Level, Head/Bow Threshold and the Head/Bow Gain faders. It is recommended to use factory presets for pads (if available) by browsing the Trigger Bank and Setup menus. However, the G9 provides a range of features to calibrate any analogue trigger pad to your playing style.
Not only the appearance of this module is the same as the Channel Select function set in Kit Editor ➔ Module 1, but also its functioning is identical. However, keep in mind that trigger monitors only update in the active mode and won´t necessarily display the same color values in the peak row when switching back and forth between Kit editor and Trigger settings.
Color Scales for Peak Detection by UI Theme UI Theme MIDI Velocity Value GEWA Red GEWA Classic GEWA White Tritanopia Protanopia Deuteranopia Grayscale Peak (126-127) Normal High (125) Normal Low (1) 11.1.1.2 A UTO S ELECT With Auto Select it is possible to select an input channel by playing the connected pad on one of its components. Turning this feature [on] will add the play-to-select feature to the standard select-bytapping function on the screen.
when saving a setup. The trigger bank preset field will show “Custom Setting”, whose parameter values can still be converted into a preset later. Don´t forget to save or create a setup after the creation of a trigger bank, otherwise the setup will recall previous trigger banks when loading it next time. However, since the new trigger bank exists, you can always make up for this by assigning the correct trigger bank preset and saving the setup again.
Factory Setups by GEWA Shell Configuration Setup Input Trigger Bank Trigger Bank Trigger Bank Kick GEWA Kick 18inch GEWA Kick 18inch GEWA Kick 18inch Snare GEWA Snare 12inch GEWA Snare 14inch GEWA Snare 14inch Tom 1 GEWA Pad 10inch GEWA Tom 10inch GEWA Tom 10inch Tom 2 GEWA Pad 10inch GEWA Tom 12inch GEWA Tom 12inch Tom 3 GEWA Pad 12inch GEWA Tom 14inch GEWA Tom 12inch Tom 4 GEWA Pad 12inch GEWA Tom 14inch GEWA Tom 14inch Ride GEWA Ride 18inch GEWA Ride 18inch GEWA Ride 18inc
Other than the Sound Select field in the kit editor, the trigger bank field is a preset field, which adds another step in the hierarchy of parameter value storage. It follows the rules and principles of the G9 preset management system. 11.2.1.3 P RESETS - S ETUP AND T RIGGER B ANK The G9 provides a variety of options to manage preset libraries. You can access the library and its functions by tapping on a Preset Field.
In case of Trigger Banks, the corresponding preset browser is structured as follows: Trigger Bank - Preset Field and Browser Preset Field Trigger Bank GEWA Snare 12inch Preset Browser – Trigger Bank Factory Trigger Bank Selection Default Presets User Presets Kicks Pads Cymbals Hi-Hats GEWA Kick 18inch GEWA Snare 12inch GEWA Crash 14inch GEWA HH14 GEWA Kick Pad GEWA Snare 14inch GEWA Ride 18inch GEWA Tom 10inch GEWA Tom 12inch GEWA Tom 14inch GEWA Pad 10inch GEWA Pad 12ich Load New Feature
11.2.1.3.1 L OADING P RESETS Proceed as follows: 1. 2. 3. Tap on the [Preset] field. Tap once on the preset you want to load. Tap [Load] in the Feature Shelf. The dialog closes automatically, and the new preset is active. 11.2.1.3.2 S AVING N EW P RESETS In preparation please check whether the [Preset] field contains the name “Custom Setting” or “Custom Setup”. This indicates that values have changed and differ from those stored with the active Trigger Bank or Setup.
Setup Custom Setup 2. Choose one of the following options: a. Overwrite an existing setup by highlighting a name in the list and tapping [Save]. b. Create a new setup by tapping [New] in the Feature Shelf, enter a name and confirm by tapping [OK]. 11.2.1.3.4 O VERWRITE P RESETS You can overwrite user presets with current values set in the interface. This function is not available for factory presets (preceding lock icon). 1. 2. 3. Tap the [Preset] field. Tap on the preset name to be overwritten.
11.2.1.4 P AD C OMPONENTS The pad component icons are located on the right-hand side of module 2. You can tap on an icon to activate the component, giving access to its parameters in module 3. The appearance of the icons and their naming depends on the Trigger Bank assigned. Assigning a cymbal trigger bank will display Bow/Bell/Edge icons and cymbal parameters in module 3, even though the corresponding input channel is labeled as e.g. “Snare”.
The following table lists all parameters available by component:
Trigger Parameters by Component Parameters Components Cymbals Drums Kick Trigger Settings Other Unit Value Range Head Head Rim Bow Edge Gain Integer 0-8 ● ● ● ● ● Threshold Integer 1-127 ● ● ● ● ● High Level Integer 8-127 ● ● ● ● ● Scan Time 1/10 ms 10-100 ● ● ● ● ● 1-127 ● ● ● ● ● 0-7 ● ● ● ● ● Parameter Name Retrigger Mask X-Talk Bell HH Controller ● High Position 0-127 ● Low Position 0-127 ● Chick Sensitivity 0-127 ● 0-60 ● ● ● ●
11.3.1 TRIGGER SETTINGS This is the first of the function sets containing trigger parameters. See the following sections for explanations and best practice approaches of each parameter. 11.3.1.1 G AIN This is simply an amplification of trigger signals received before input. Some piezo ceramic elements available on the markets produce precise, but weak signals, which can be amplified by the gain feature before being recognized as input signal.
Trigger Monitor Pad Monitor 17 31 122 X-Talk Monitor 64 11.3.1.2 99 72 105 127 83 79 11 Kick Snare Tom 1 Tom 2 Tom 3 Tom 4 Ride Hi-Hat Crash1 Crash2 Aux 1 Aux 2 Aux 3 Aux 4 T HRESHOLD With this dial you adjust the velocity threshold from which on the G9 accepts signals sent by the detecting sensor (voltage). Low thresholds are preferable for sensitive players, but often cause auto triggering due to vibrations of the environment.
11.3.1.3 H IGH LEVEL High (top) level of the input. In conjunction with the Threshold it sets the boundaries of the span of relative electrical signals to which the MIDI velocity value range (0-127) is mapped. Signals with relative electrical levels between Threshold and High Level will produce MIDI notes with velocities between 1 and 127. Any signals with relative electrical levels above High Level will produce MIDI notes with velocity 127.
Retrigger Mask parameter value range: 1-127 11.3.1.6 X-T ALK X-Talk is a tool to avoid triggering of unwanted signals caused by other pads in the immediate vicinity. When instruments are mounted on a rack or stands which have physical contact, playing on one instrument can cause shock-like vibrations. As a result, trigger sensors are activated in a more aggressive way than the impact of natural sonic waves would have on surrounding acoustic instruments.
too low you may not be able to get fully closed Hi-Hat Sounds, even if the cymbals are in closed position with a good amount of pressure on the Hi-Hat Pedal. Low Position Parameter Value Range: 0-127 11.3.1.9 C HICK S ENSITIVITY (H I -H AT P EDAL ONLY ) Measured against CC MIDI message value: 0 - for fully open, 127 - for fully closed. Set the level below which a following pedal 'step on' will generate a chick. Chick Sensitivity Parameter Value Range: 0-127 11.3.1.
G9 Hi-Hat Calibration Graphic Elements Hints Tap the Hi-Hat Pedal icon in module 2 to select the Hi-Hat Controller/Pedal. Tap the [Calibrate…] button in module 3 Calibrate… Hi-Hat Calibration High Position 109 Low position 90 Cancel With this dialog you can calibrate the parameters Low Position and High Position of your Hi-Hat Pedal. For best results follow the instructions step by step. Tap [Next] to start the calibration.
11.3.2 ADVANCED SETTINGS This is the second of the function sets containing trigger parameters. See the following sections for explanations and best practice approaches of each parameter. 11.3.2.1 D YN L EVEL & D YN T IME Dynamic Threshold level and Dynamic Threshold decay time for the input. Also, two very important parameters. Raising both Dyn Level and Dyn Time will tell G9 to suppress false triggering harder (crosstalk between inputs and double triggering).
Single: Head/Bow and Rim/Edge are treated as two different pads. An application would be a simple single zone pad with single piezo triggering. Dual: Sets the Head/Bow Channel up in a way that Rim/Edge signals are expected to use the same Input Channel as Head/Bow. In combination with this choice you must also specify, how the Rim/Edge signals are detected (Piezo or Switch). Change to the other components by tapping on the component icons and check your settings for every input channel.
Peak Input Kick Snare Tom 1 Tom 2 Tom 3 Tom 4 Ride Hi-Hat Crash1 Crash2 Aux 1 Aux 2 Aux 3 Aux 4 2. Select a component to edit by tapping the corresponding icon in module 2 (Trigger Selection). 3. 4. Tap the function set Advanced Settings in module 3. Tap once on the [Curve Settings] field. Curve Settings Linear 5. Select one of the curves in the Presets or User column by double tapping. Curve Settings Presets 6.
Trigger Setup Selection GEWA STUDIO 5 GEWA PRO 6 GEWA PRO 5 User Setup 1 (Highlighted) User Setup Number 2 Load b. Save Rename New Delete As a Trigger Bank (Preset indirect): i. Tap the Trigger Bank field (module 2). Trigger Bank Custom Setting ii. Select a User Trigger Bank in the drop-down list and tap [Save] to overwrite the highlighted entry. Alternatively tap [New] to create a new Trigger Bank with current parameter values visible in the User Interface.
The following table shows the drop-down list which opens by tapping the Curve Settings field: Curve Settings Presets User (Editable) Linear Custom 1 Convex 1 Custom 2 Convex 2 Custom 3 Convex 3 Custom 4 Convex 4 Custom 5 Convex 5 Custom 6 Convex 6 Custom 7 Concave 1 Concave 2 Note: Trigger curves work on a pad component level. Assigning a new curve will only affect the active component (Head, Rim, etc.) in module 2 of the selected pad under input channels (module 1).
11.3.2.5.1 1. C REATING C USTOM C URVES Select an Input Channel in Module 1(Pad). Peak Input Kick Snare Tom 1 Tom 2 Tom 3 Tom 4 Ride Hi-Hat Crash1 Crash2 Aux 1 Aux 2 Aux 3 Aux 4 2. Select a component to edit by tapping the corresponding icon in module 2 (Trigger Selection). 3. In the the function set Advanced Settings (Module 3) tap once the [Curve Settings] field. Curve Settings Linear 4. Select one of the curves in the User Presets column by double tapping.
Curve Editor Curve Setting Save 7. 8. 9. 10. Custom 2 Undo (Optional) Add/remove another control point by tapping [+]. (Optional) Rename the curve by tapping the field [Curve Setting] to open the keyboard. Tap [Save] in the Curve Editor to store the new curve shape. The curve itself is a preset which will only take effect if it is assigned to a trigger bank preset or setup.
Curve Editor – Feature Shelf Undo (Returns to the initial curve shape before opening the Curve Editor) Save (Saves the curve points as seen in the UI) 11.4 MODULE 4 11.4.1 TRIGGER MONITOR Trigger Monitor Pad Monitor 31 17 X-Talk Monitor 64 122 72 99 127 105 79 83 11 Kick Snare Tom 1 Tom 2 Tom 3 Tom 4 Ride Hi-Hat Crash1 Crash2 Aux 1 Aux 2 Aux 3 Aux 4 In this module you will find all visual monitors tracking the input signals of each pad component.
11.4.1.1 P AD M ONITOR Monitors all registered signals of the Input Channels by returning the stroke velocity in the standard MIDI range of 1 to 127. A time series of the last 10 strokes is displayed in the viewport. Detected head strokes and rim strokes are distinguished by the color of the bars and depend on the UI Theme chosen. See the color table in the previous section for reference. The actual velocity value of a stroke is shown at the bottom of each peak and visualized by the height of the bar.
12 GENERAL SETTINGS All adjustments made in this mode affect device specific parameters, which are stored globally and memorized on next start up. Here you will find more options such as controls for Master Outs, Direct Outs and Digital Outs including equalizers and compressors. You can also control the routing of pads and the routing of other input signals.
12.1.1 MASTER OUTS This function set provides adjustments for the standard outputs of the console such as Master Outs (XLR, S/PDIF), Monitor Outs or Phones. The volume dials are instances of the corresponding hardware dials on the left-hand side. Consequently, values of the hardware dials will update when adjusting the volume of an output in Master Outs. The Balance dials however can only be found in this location, allowing for correcting acoustic properties of the environment or connected hardware.
To be able to handle Dual Mono configurations, the 8 individual Mono Outs are arranged in groups of two (1 - 2, 3 - 4, 5 - 6, 7 - 8). A second L/R icon is added to each group. In Direct Outs L/R icons are interactive and function as buttons to switch between Dual Mono and Stereo configuration.
The G9´s routing function is divided into 2 input categories: Routing Drums and Routing Others. While their routable channels vary, the functionality and appearance are the same. Thus, the contents of the following subchapters apply to both input categories likewise.
12.1.4.1 1. E DITING THE R OUTING M ATRIX Tap on [Routing Drums] or [Routing Others] to open the corresponding Routing Matrix. Note that the Input Channels, effects and routable sound sources (Pads in particular) are arranged horizontally (Columns), whereas the available Output Channels are arranged vertically (Rows). Big dots indicate in which output an Input channel is audible and small dots show channels which are muted in the Mix sent to an output. 2. 3.
2. 3. Switch between the L/R icons by tapping on the corresponding button. Open the Routing Matrix again and check the state of the L/R icons on the right-hand side. Direct Outs - Configurations Stereo Configuration Dual Mono Configuration 12.1.4.2 P RESETS – R OUTING The G9 provides a variety of options to manage preset libraries. You can access the library and its functions by tapping on a [Preset] field next to a group of preset parameters.
Preset Management -Feature Shelf Function Preset Type Load Save Rename New Delete Factory Preset User Preset Factory presets provided serve as a starting point to avoid time consuming edits of about 100 dots manually. Chose the preset that brings you closest to the desired routing design and selectively alter the settings where needed.
With Custom Setting visible proceed as follows: 1. Tap the [Routing Preset] field. Routing Preset Custom Setting 2. 3. 4. Tap [New] in the Feature Shelf. Name your preset using the keyboard. Confirm by tapping [OK]. 12.1.4.2.3 O VERWRITE P RESETS You can overwrite user presets with current values set in the interface. This function is not available for factory presets (preceding lock icon). 1. Tap in the [Routing Preset] field. Routing Preset Custom Setting 2. 3.
12.2 MODULE 2 The second module of the General Settings mode hosts Equalizer and Compressor features for outputs as well as Control settings for peripheral devices such as Foot Switch pedals or control via a pad using an AUX input channel. 12.2.1 MASTER CHANNEL | HEADPHONE | MONITOR OUTS All Outputs in this module provide a 4-band full parametric equalizer and compressors that function in the same way. Therefore, we will discuss both features exemplary.
12.2.1.1.1 P ARAMETERS AND D ESCRIPTION Equalizer - Parameters per Band Parameter Value Range/Unit Low Band Mid Band 2 Mid Band 1 High Band Shelving --- ● --- --- ● Q Factor 0,1 – 8,0 --- ● ● --- 20 Hz -16 kHz ● ● ● ● -15 dB – +15 dB ● ● ● ● Frequency Gain Equalizer – Description of Parameters Parameter Description Shelving Attenuates or boosts frequencies above (High Band) or below (Low Band) a specified Shelf Frequency by the Gain Value.
5. Activate the matching frequency band on the right-hand side by tapping once on its parameter bar. 6. Note that you can access the parameters and manipulate the associated Curve Points in 3 alternative ways: a. b. c. By tapping directly on a dial in the parameter bar By turning the hardware dials assigned each parameter By tapping on one of the upper three software dials next to the hardware dials 7.
G9 Compressor Compressor Custom Setting Preset 0 -6 0 -6 0 -6 -18 -18 -18 -36 -36 -36 -64 -64 Input 12.2.1.2.1 Boost Knee Ratio Attack Threshold Release -64 GR Output P ARAMETERS AND D ESCRIPTION Compressor - Parameters Parameter Value Range/Unit Description Boost 0 - 24 dB Amplifies the compression result to compensate for the loss in levels caused by the Ratio setting. This parameter applies to the full dB spectrum of the track (threshold settings are ignored). Ratio 1.
12.2.1.2.2 E DITING C OMPRESSOR C URVES The following steps are a guideline for setting up a compressor: 1. Turn Compressor [on]. 2. (Optional) Play a song in Song Player and/or play on the drum kit to hear the effect of your edits. 3. Tap the [Compression] field which contains the input-output curve. A dialogue pops up giving you access to the compressor parameters. Compressor Custom Setting on off Input GR Compression Output 4. Set the [Threshold] for the Compressor to start working. 5.
any separate storage, otherwise there is no difference in the structure of the preset hierarchy. You can simply replace the word “Drum Kit” with “Device Database” in the following Illustration: The G9 provides a variety of options to manage preset libraries. You can access the library and its functions by tapping on a [Preset] field next to a group of preset parameters.
12.2.1.3.1 L OADING P RESETS Proceed as follows: 1. 2. 3. Tap on the [Preset] field. Tap once on the preset you want to load. Tap [Load] in the Feature Shelf. The dialog closes automatically, and the new preset is active. 12.2.1.3.2 S AVING N EW P RESETS In preparation please check whether the [Preset Field] contains the name “Custom Setting”.
3. 4. 5. Tap [Rename] in the Feature Shelf. Enter a name for the new preset using the keyboard. Confirm by tapping [OK]. 12.2.1.3.5 D ELETING U SER P RESETS This function is not available for factory presets (preceding lock icon). Proceed as follows: 1. 2. 3. Tap the [Preset] field. Tap once on a preset name in the drop-down list. Tap [Delete] in the Feature Shelf. 12.2.
Control Options Control Description Control 1 Control 2 Off Disables Control Function Off Off Kit Select Browse Drumkit Library Previous Drum Kit Next Drum Kit Fixed Hi-Hat Switch between fixed Hi-Hat and open Hi-Hat Closed Hi-Hat Open Hi-Hat Stage Mode (Open) Toggles between On Stage and Home Screen Stage Mode Home Song Player Controls basic Player Functions Pause Stop/Play Setlist Tile Change Cycle through Stage Tiles Previous Setlist Tile Next Setlist Tile Control Sockets: (B
12.3.1 MIDI 12.3.1.1 G LOBAL MIDI S ETTINGS (S OFT T HRU ) This function set centers around connecting the G9 with other MIDI devices to form an in-line signal path for MIDI control data to travel through. Utilizing the MIDI 1.0 protocol, it is consequently possible to remote control certain functionalities between the connected devices. Note that in order to establish a working MIDI Data connection or chain it is crucial to know the MIDI implementation of all devices connected.
G9 MIDI Routing – Fields and Options MIDI Input Local Control • off • on • • • to MIDI-Out to USB-MIDI to both • off USB-MIDI Selection MIDI Channel • off • 10 • to MIDI-Out • • • • • • • • • • • • • • • • 11 12 13 14 15 16 off 1 2 3 4 5 6 7 8 9 Selection Default factory settings are highlighted in bold letters. 12.3.1.1.2 L OCAL C ONTROL The next column of the Global MIDI Settings consists of the fields Local Control and Midi Cannel.
off Blocks all G9 MIDI control data received from the Input Channels (Pads) from accessing the internal sound engine. This data can still control other connected equipment via the MIDI Outputs available (A). The control data routs back into the console indirectly via the external MIDI device (B). Hint: Check the Local Control setting, if you cannot hear any sound when playing while the trigger monitors receive signals from the connected pads.
G9 Continuous Controllers CC Component Continuous Controller (CC) HHPedal CC Start (Default) Snare CC Start (Default) Ride CC Start (Default) Toms/Aux CC Start (Default) Start (Default) Kit Volume 12.3.2 Description • 4 Foot • 11 Expression • 16 General 1 • 17 General 2 • 18 General 3 • 19 General 4 • off off • 1 Modulation • 2 Breath • on • off Channel Selection DRUMKIT PROGRAM CHANGE This feature set defines the rules for MIDI program changes.
b. Tap the [Drum Kit] field to choose a kit from the Drum Kit Browser by double tapping. 2. Tap the [Program Change] field to enter a program number using the number pad. 3. (Optional) Repeat steps 1-2 for other drum kits. The settings of the function set apply to the following ports of the rear panel. Make sure that the G9 is connected to the external device in order to let the settings have effect: Ports – MIDI MIDI Out MIDI In USB-MIDI (digital) 12.3.2.
12.4 MODULE 4 The last module of the General Settings mode hosts all global device adjustments. The features hosted comprise a shutdown timer, appearance of the screen and knobs, UI Themes as well as important information about the device. This module also manages wireless connections and allows for performing a factory resets and Updates. 12.4.1 DEVICE This function set controls all adjustments regarding UI elements.
12.4.1.4 UI T HEME The appearance of the G9 is customizable by different UI Themes. Tap on the field and select a theme using the selection wheel. There are also themes dedicated to different types of color blindness. These themes are named after medical terms and utilize only color values from the perceivable spectrum of the concerned group of people.
12.4.3 BLUETOOTH The built in Bluetooth function is useful for streaming music from an external player into the console. To establish a Bluetooth connection, you need to follow the steps below. Note that steps 2-5 take place on your mobile device and the procedure might vary from manufacturer to manufacturer. Please refer to the owner’s manual of your mobile device if you have problems establishing a working Bluetooth connection: 1. 2. 3. 4. 5. 6.
a. b. Tap [set Name] to close the dialogue and set the name shown in the display. Tap the field containing the current [Bluetooth Name] and enter a custom name using the Keyboard. G9 – Custom Bluetooth Name Bluetooth Name GEWA G9 This is the name under which the device will be visible Set Name 4. 12.4.4 Confirm by tapping the Hook [✓] in the Keyboard. FACTORY RESET A factory reset will restore the default settings of the firmware version installed.
12.4.5 INFORMATION This function set provides all information regarding the status of the G9 such as Serial Number, Firmware version, sound chip firmware version (Dream FW) and version number of the trigger firmware (Trigger FW). Also shown is the status of the internal memory usage (Flash for imported sample Libraries and SD Memory). Please always communicate Serial Number, Firmware Versions and installed Sound Bank/Trigger Bank versions when contacting the customer service.
12.4.6.1.2 D IRECT D OWNLOAD VIA M ODULE The direct download feature avoids media disruptions, resulting in a fast and easy procedure to keep your G9 up to date. Please follow the steps described below: 1. 2. 3. 4. Make sure you have established a working Wi-Fi connection. Go to General Settings ➔ Module 4 ➔ Update Tap on the [Language field] to choose the language of the manuals provided. Tap [Check for Update] to open the Update Dialogue.
The relevant folder paths are: • • Firmware: INTERNAL SD/SYSTEM/Firmware Manuals: INTERNAL SD/SYSTEM/Manuals System Folders in File Manager INTERNAL SD/SYSTEM/ Drumkits Firmware Manuals QuickRecord Custom User Folder with content Copied Song in m4a Format.m4a Flac Audio File.flac 12.4.6.2 U PDATE YOUR D EVICE Important: Note that the update routine requires a specific file naming convention and file extension in order to work correctly.
G9 - Update via USB Reboot extract copy to ROOT turn off plug in turn on remove Reboot reboot Tip: Check the successful update in the information tab. Go to General Settings ➔ Module 4 ➔ Information. The Firmware version should have updated accordingly. If you observe trigger version V0, another reboot might be necessary. Tip: In combination with the direct firmware download you can grab the unzipped firmware from the default download folder and copy it on your USB Stick using the G9 File Manager.
13 TOOLS The tools mode contains app-like utilities and features like an On Stage mode, PDF Reader, an Import Tool for sound samples and a File Manager. Tapping an icon in the Tools menu will open the associated application.
On Stage - Default Set List Editor Drum Kit Studio Record Set Blank Sheet 1 2 3 4 5 6 7 8 Metronome TS: 4/4 Song Player 120 IV: 1/4 3 bpm Song select empty The following sections will focus on editing tiles, managing setlists and working with setlists on stage. 13.1.
13.1.2 EDITING TILES – ASSIGN EXPRESSIONS FOR MEDIA TYPES In preparation, please tap the [Setlist Editor] field and load the preset Blank Sheet by double tapping on the preset name. This will load an empty setlist with default values. The proceeding described in the following applies to creating new presets using the blank sheet preset as well as editing tiles of any other existing setlist.
13.1.3 SETLIST PRESETS A set of 8 occupied tiles can be saved as a setlist, which remembers all media types assigned to the different tiles once the setlist is loaded. The UI will update as soon as a tile of the loaded setlist is activated. A setlist is the same as a preset and is treated the same way. Regarding setlists, the preset browser provides only one preset called “Blank Sheet”. This preset loads default values without any pdf attachment.
i. ii. b. Highlight a list entry (Tap once). Tap [Load] in the Feature Shelf. Double tap a list entry. Select Stage List Preset Blank Sheet Jazz Standards Set 1 Jazz Standards Set 2 Jazz Standards Set 3 Top 40 Set 1 Top 40 Set 2 Load 13.1.3.2 Save Rename New Delete N EW S ETLISTS Proceed as follows: 1. 2. Load a preset to start from. Edit the tiles as desired (The Setlist Editor field updates to ”Custom Setup”). Setlist Editor Custom Setup 3. 4. 5. 6.
This overwrites the chosen preset with the current tile layout. 13.1.3.4 R ENAME S ETLISTS Renaming of setlists is always possible without overwriting their tile configuration. This option is only available for user setlists. Proceed as follows: 1. 2. 3. 4. 5. Tap the [Setlist Editor] field to open the setlist browser. In the preset browser highlight a user setlist to be renamed (tap once). Tap [Rename] in the Feature Shelf. Enter a new name using the keyboard. Confirm by tapping [OK]. 13.1.3.
13.1.4.1 P DF V IEWER The On Stage Pdf Viewer is a simplified version of the Pdf Reader (see on page 142). It provides only the most important functions for reading chart music. During live performances you need to turn pages quickly and have fast access to the [Play/Stop] buttons of the On Stage mode to quickly react to issues on stage. The built-in [Exit] button closes the Pdf viewer and returns to the active tile in On Stage mode.
13.2 PDF READER The PDF reader allows you to read any PDF stored onto a USB stick or the internal memory, which is very useful for reading sheet music. Next to basic navigation functions, it also provides advanced functions such as bookmark navigation and thumbnail navigation. On Stage PDF Reader Import Tool Shop File Manager Tools Tapping on Tools ➔ Pdf Reader will open the application. All functions available are visible in the start screen: PDF Reader Document Name.
13.2.1 FILE SELECT BROWSER The File Select Browser is implemented in various applications in the G9, such as the Song Player, PDF Reader or Import Tool. However, depending on the application, it opens with different filters active to only show relevant file types. Regarding the Pdf Reader, it displays pdf files only. Consequently, non-interpretable files are hidden. 13.2.1.
13.2.1.2 O PEN P DF F ILES In Pdf Reader, proceed as follows: 1. Tap on the [Folder] icon in the top-right corner to open File Select. 2. Specify the storage medium by tapping once on [USB] or [SD]. 3. Navigate to your file by performing one or more of the following actions. a. Double tap on folder names to open them (left column). b. Move up the path by tapping the [white bar] (left column). SYSTEM/ 4. Select a file to open by double tapping list entries in the right column. 13.2.
PDF Reader Page Select Page select 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 13.3 FILE MANAGER The built-in file manager is an application to transfer data between an external USB device and the internal SD card. It can be used to manage your files as you would do on a regular PC or Mac. Move, copy, delete and rename files and folders of both sources (internal SD card and external USB device).
13.3.1 FILE MANAGER VS. IMPORT TOOL The Import Tool is designed to add samples to the Sound Library of the G9. It does not transfer data onto the internal SD card, but takes sound files from any source and encrypts the sample file into the G9´s native library format. Samples are encrypted and filed under the matching instrument category in the library. Consequently, samples are finally stored on the built-in Flash Memory for fast access and minimal load time.
File Manager Split Windows File Manager Free Disk Space SD Card Directory Path split window 1 Type Free Disk Space USB Directory Path split window 2 – The Flag indicates that this directory is destination for the compiled Collection in window 1 Name Select Type Name Folder 1 Folder 1 Folder 2 (Selected) Empty Folder 1 (Highlighted) Select File 1 … … … Active split window with highlighted frame … Resize Window (tap and drag) … … Inactive split window Task Bar Filter 13.3.
o o o o Create new folders: always possible in the active split window, regardless whether there are existing collections Rename Files/Folders (only one list entry at the same time) Delete Files (batch processing) Transfer buttons (Move/Copy) to start the transfer Job.
The definition of a collection extends the understanding of file management in ordinary file browsers and distinguishes itself from the term selection. While traditional file managers discard file selections as soon as you leave a folder to open a different directory, the G9 file manager remembers these selections, allowing to add more files from other directories. Thus, a collection consists of selections spread out on different directories and storage mediums.
cancel the operation. Tapping the [Refresh] button will delete the collection of the active split window. 13.3.5 COMPILING COLLECTIONS Proceed as follows: 1. Tap inside a split window to activate it as starting point. 2. Navigate to the directory with the relevant files using one or more of the following Options: a. Select a drive. b. Use the path navigation buttons (Root Directory, One Level Up). c. Use the Search function 3.
13.3.6.2 M EMBERSHIP OF A C OLLECTION Within the concept of collections, no file or folder can be member of more than one collection. Without this rule, a file in collection 1 could be moved to a different destination in first place. If it was member of collection 2 as well, the job protocol would address a dead path by the time of processing the job task of collection 2. To avoid this conflict, the File Manager does not allow for double checking files and folders.
• Delete o o Collection based, affects all members of the collection in the active split window. Always asks for permission before executing the job. Delete will trigger a warning message, allowing to change your mind and cancel the operation. Undo and Redo functions are NOT available in conjunction with Move, Copy and Delete. 13.3.
13.3.9 HISTORY – UNDO AND REDO The G9 File Manager features a 10-step history recording the following actions: a. b. Directory nodes visited across all storage mediums (SD, USB) Selections This means that it tracks all actions across both split windows. Use the [Undo] and [Redo] buttons to move back and forth in history. Task Bar - History Undo (up to 10 steps) Redo (up to 10 steps) 13.3.
13.4.1.2 C ONCEPTION In File Manager, the search function serves as an In-line feature when compiling collections (see 13.3.5 Compiling Collections on page 150). Meaning, that it can be utilized at any time and alternatively to linear folder navigation. Consequently, the search dialogue inherits all relevant icons of the task bar needed to serve this purpose.
• • • • • • • • • Navigate down the path by double tapping a folder. Double tapping does not select files/folders. Double tapping opens folder – Auto deletes search term (auto refresh) to view folder contents and edit selections caused by parenting. Double tapping files ➔ no selection, just highlight List with results obeys filter and ordering settings. Selection via the check boxes Multiple selections possible “Check All” selects the complete result list only.
13.4.2.1 P ROPERTIES Each file browser of the G9 provides filtering and ordering options which operate independently from each other. Consequently, the Filter Manager only affects browsers, where it is available.
13.4.2.2 F ILTERS AND S ORTING O PTIONS The following table shows the complete list of sorting options and categorized Filters available. The G9 Filter Manager orders file categories by relevance to minimize the need of scrolling down the list during your daily work. Selections made in the Filter Manager will not affect File Select browsers (Song Player or PDF Reader), but only apply to the split windows of the File Manager.
13.5 IMPORT TOOL With the import tool it is possible to import files which are meant to be accessible in the sound library. Apart from the copy process, these files need to be encrypted into a G9 native format. If you just want to transfer files to the internal drive, please use the File Manager. The import tool addresses the reserved partition for user samples on the built in 4 GB flash memory. The required file format for the import of custom sounds is wave.
Importer Library 1 101 Imported Container B Sample Bow Sample Edge Sample Bell Imported Custom WAV 1 Storage Sound Package 1 (Collapsed) Container A Container B (imported) Container C Sound Package 2 (Expanded) 2 2 + Imported Container 1 Instrument 1 Instrument 2 Instrument 3 - Container 1 (imported) Container 2 (not imported) Container 3 (not imported) 102 Imported Custom WAV 2 103 Imported Custom WAV 3 Memory Usage: 23% Status: 10% 13.5.
G9 File Select Browser - Source Selection and Search Intern USB Search Navigation – Up the path SYSTEM/ G9 File Select Browser (WAV) File Select Intern USB Search Filter Cabasa_Stroke.wav Clacker.wav Copper_tambourine.wav SYSTEM/ Daiko_Open.wav DrumKits Elevator_Open.wav Firmware Manuals Garage_Door.wav QuickRecord Double Tap to import this File.wav Triangle_Large.wav Sorted by Name Date Type The Sound Browser is explained in detail in the Kit Editor section.
G9 Sound Browser Sound Browser Sorted by Instrument Category Kick Drums Snare Drums Toms Ride Cymbals Crash Cymbals Hi-Hats Cymbals SFX Percussion 1 Percussion 2 Wave Source Number Instrument Cat 001 14” Collectors Maple C AC 002 14” Collectors Maple S AC 003 14” Collectors Maple CS AC 004 14” Collectors Maple Rim AC 005 14” Collectors Maple X-Stick AC 006 14” US Vintage C AC 007 14” US Vintage S AC 008 14” US Vintage CS AC 009 14” US Vintage Rim AC 010 14” US Vin
Deletion of imported Sounds removes the Library entry of the Import Tool as well as its entry in the Sound Browser. 13.5.5 IMPORT LIMITS AND SOUND MANAGEMENT Both, Wave file import and import of sounds from the Shop address the built-in 4 GB flash memory. This way you have quick access to your sounds while playing, resulting in fast loading times for drum kits using the Drum Kit Selector or the On Stage tool.
13.5.5.3 R EACTING TO IMPORT LIMITS The answer is simple: Delete unused sounds from the sound library and don´t be afraid to do so! Deleting a sound from the library will generate free space on the internal flash memory. This is realized by tapping the trash can icon in the Importer (See section 13.5.1 Importer on page 158). While the technical side is easy to solve, concerns about the loss of data might follow and need to be addressed. In the following we will provide a few tips to dispel doubts. 13.5.
13.6.1 1. CONNECTING TO THE CLOUD Go to Tools ➔ Shop to open the Cloud browser. On start-up you are disconnected from the cloud by default and the landing page of the shop browser asks you to connect you G9 to the Cloud. 2. Tap on the [Status] button in the bottom left corner of the shop screen. Icons - Cloud Status button (Tap for connection details) This will call up the Login pop-up.
3. Tab [Connect] which should change the status to “connected” (highlighted in green). 4. Close the Login dialogue by tapping [X]. The Pop-up closes, and you should see your purchased items listed in the Sounds tab. 5. 6. 13.6.2 Browse the sounds sub tabs to view your purchased sounds by category. Tap [Download] for sounds you want to import into the sound library and proceed with the import process. (see 13.5 Import Tool on page 158).
14 USEFUL INFORMATION 14.1 EXPLANATION OF TERMS Term Definition MIDI Musical Instrument Digital Interface is a data transfer protocol. With this, musical control information is transferred between electronic instruments such as digital pianos, keyboards, synthesizers, drum computers or even PCs or laptops. To exchange this control information, the instruments/computers require MIDI connections and a link must be established between them.
14.2 WARRANTY Warranty for a period of 2 years from the date of purchase on hardware and workmanship is granted by the dealership where the digital drum set or console was originally bought. In the event of a proven defect, the buyer has in the first instance only the right to receive supplementary performance. Supplementary performance includes either rectification or supply of a replacement product. Equipment or exchanged parts become to be the property of the processing dealership.
15 TROUBLESHOOTING AND POSSIBLE SOLUTIONS Problem The console does not boot when pressing the power button. The user interface freezes (no reaction to finger gestures). Possible Solutions 1 1 Make sure the power cord is connected correctly to electrical outlet and apparatus. Live installations will cause power button to light up. (stand-by ➔ red, on ➔ white) Perform a hard reset by holding down the power button until the device shuts down. Try to restart by tapping the power button again.
16 TECHNICAL DATA G9 Drum Workstation – Technical Data Drum-Kits 40 Preset + unlimited User Presets Instruments more than 400 Effect Types Pad Compressor & 3-band full parametric EQ per Pad Output Compressor & 4 Band full parametric EQ per Output Room Reverb & Instrument Reverb: 12 Types / Multi Effects: 9 Algorithms 100 Wave and 100 Multi layered full instruments (Head/Rim/X-Stick - Bell/Bow/Edge) User Sample Import File Format: WAV (only PCM format) (44.
