Installation Guide

Please leave this sheet and warranty for the customer for future reference
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Friday
Faucet Installation Instructions
PD120
Figure 1a
Step 1a Three Hole Mounting
Screw bolts to the escutcheon. Insert escutcheon
assembly through the base plate and the holes of
the sink.
Screw quick connector to the free end of
pull-down hose. Align block (3A) and tabs (3B)
on quick connector. Push quick connector
housing firmly upward to snap onto receiving
block. Pull down with moderate pressure to
ensure connection has been made. After
connecting the hose, attach weight (3C) onto
the black house at bottom of the loop to
prevent hose from twisting.
Insert faucet through hole in escutcheon. From
underneath sink, attach rubber washer (1A),
metal washer (1B), and nut (1C). L
ock nut (1C)
into po
sition by tightening screws (1D).
Step 1b Three Hole Mounting
Step 3
Hole diameters are 1 5/16" minimum to 2" maximum
Maximum deck thickness is 3" (single hole/faucet only mounting) or 2 1/2" (with soap pump
,
without escutcheon) or 2 3/8" (with escutcheon)
This kitchen faucet comes completely assembled and water tested
Includes braided nylon supply lines with
3/8" C
ompression Inlets
Tools required-channel lock pliers (or pipe wrench), basin wrench and small crescent wrench
Faucet Installation Instructions
For additional assistance or service call: 1-888-560-5222 USA 8:30 a.m. to 5:30 p.m. EST Monday-Friday
Please leave this sheet and warranty for the customer for future reference
Figure 3
Figure 2
Step 2 Single Hole Mounting
Insert faucet through hole in sink or countertop.
From underneath sink, attach rubber washer
(2A), metal washer (2B), and nut (2C). Lock nut
(2C) into position by tightening screws (2D).
Page 1 Page 2
Shut off water supply prior to beginning installation
Parts
Maintenance: Clean with warm water, soft cotton
cloth and non-abrasive liquid dish soap. Towel dry.
Never use acids, harsh abrasives, detergents, or
products containing chlorides on any parts of this
product.
Figure 4
Step 4
Figure 1b
Figure 5
Step 5
Install Soap Dispenser (Optional)
Remove th
e bottle. Separate hea
d from body
assembly by holding the flange and p
ull
ing up on
t
he dispenser head taking care
not
to pull directly
on the spigot. Make sure the flange is proper
l
y
seated then inser
t body assembly through
selected hole in sink and secure w
ith nut.
From
under the sink screw the bottle onto the body
assembly shank. Fill bottle with soap from above
counter then attached soap di
spenser
head.
NOTE: To ref
i
ll soap bottle simply remove
dispenser
body and fill from above counter.
Figure 6
Step 6
Important: After installation is completed, to
prevent damage to the internal parts of your
faucet from debris that may have collected in
the water lines, it will be necessary to flush the
faucet. Turn on hot/cold water supplies and
remove spray head. Hold the end of the hose
down into the sink and turn the faucet on to the
warm position so hot and cold water are mixed.
Flush water lines for one minute. Check for
leaks and re-tighten any connections if
necessary. Reinstall spray head by screwing
onto end of hose by hand.
1A
1B
1C
3A
3B
3C
PD120
Polish ChromePC
*Specify
Finish
Finish Codes
2C
2B
2A
RP38190* Spray
Head & Hose
RP20005 Cartridge
RP70394 Bonnet
RP80028
*
Cap
RP50097 Screw
RP50002 Set Screw
RP13320* Handle
RP60002 O-ring
RP70421 Block
RP70223 Weight
RP60089 O-ring
RP70438 Quick Connect
RP56036 Mounting Nut
RP50071 Bolt
RP80396 Base Plate
R
P80395* Escutcheon
RP46056*
Flang
e Assembly
RP46024 Bottle
RP46055*
Soap Dispenser
RP56075 Nut
R
P
64024 Washer
RP64023 Washer
RP50004 Screw
Neatly coil any excess hose and make connections
to water lines
. Thread the nut (4A) on supply line
onto outlet of water supply valve (4B) and tighten
with wrench. Do not overtighten.
4A
4B
1
D
2D
NOTE: This faucet is equipped with a
two function
sprayer plus a Pause
function. Once the
faucet turne
d off it
will automatically revert back to
r
egular
aerated stream.
Button A: Changes flow from regular
stream to full spray.
Button B: Changes flow from full
spray to
r
egu
lar s
tream.
PAUSE: To initiate Pause p
lea
se press
& hold Button B. Release when you
wish to have water flow begin again.
Button B
Button A
Stainless Steel PVDSS