User Guide

ManualsBrandsGianni Industries ManualsDoorAD-425S

P-MU-AD425S Ver. A Publish:2008.07.11 Page: 1/ 20

AD-425S Automatic Door Operator

Instruction Manual

General Safety Precautions

z This instruction manual is intended solely for use by qualified professionals. All

installations, electrical connections and adjustments must follow the installation

instructions.

z Please read this manufacturer's instructions carefully before installing this unit. Incorrect

installation may result in severe personal injury and/or damage to property.

z Packaging materials (plastic and polystyrene, etc) should be disposed of without causing

environmental damage and should be kept out of reach of children.

z Do not install this unit in a chemical explosive environment or atmosphere to prevent a

risk of explosion. The location of this unit is important in achieving proper performance

and normal operating life. This unit should be installed in a safe operating condition

z Make sure the construction‘s strength and stability are up to standard. Manufacturer will

not be held responsible for any damage resulting from incorrect use of this unit.

z These safety devices (e.g. photocell and emergency stop) must follow the technical

safety regulations and current safety standards, including limiting of forces and speeds to

ensure the door operator works very well at all times.

z The safety devices must protect any areas where the risk exits of being crushed, cut or

gagged or where there are any other risks generated by the motorized door or gate.

Apply hazard areas notices required by applicable regulations.

z Each installation must clearly show the identification details of the motorized door/gate.

Encoder

Photocell

Summary of content (20 pages)

PAGE 1
AD-425S Automatic Door Operator Instruction Manual General Safety Precautions z z z z z z This instruction manual is intended solely for use by qualified professionals. All installations, electrical connections and adjustments must follow the installation instructions. Please read this manufacturer's instructions carefully before installing this unit. Incorrect installation may result in severe personal injury and/or damage to property.
PAGE 2
z z z Make sure the voltage specified as correct for the device. Must provide at least 10 seconds rest time between every restarting cycle to ensure adequate residual current can be returned to power system. Make sure to turn the power off before installing and checking this unit and to avoid the risk of fingers that are in contact with the electronic components. External interconnection wiring should be performed wearing the antistatic glove.
PAGE 3
All Packing materials 1. Construction Name 1 ○ 7 ○ 12 ○ Cover ○ 2 Motor ○ 3 Reducer ○ 4 Square Couplings ○ 5 Control Board ○ 6 Battery 2. Power Switch ○ 8 Operating Arm ○ 9 Sliding Rail ○ 10 Stopper Ball ○ 11 Baseplate Transformer Control Board Make sure the voltage specified as correct for the device. For safety reasons, we recommend user not to install this operator with a Fail-Secure Electric Locks (Power to open) in case of emergencies or power interruptions. Copyright All Rights Reserved.
PAGE 4
3. Control Board Guide Input/Output Contact Explanation Remark Make sure the input is used correctly (AC110 or 220V). When turn on the power switch, it enters a learning mode. Power Switch AD-425S Operating Arm turns clockwise. (See Figure 5~8) AD-425S Operating Arm turns counter-clockwise. (See Figure 5~8) DIP3 switch ON, when the external pressure force either “WIND” or “MAN MADE FORCE” occurs, AD-425S will automatically open and close.
PAGE 5
Input/Output Contact Explanation Remark Jumper 1-2 is N.C. contact. N. C. (default) Jumper 1-3 is N.O. contact. N. O. (default) Jumper 1-8 is N.C., or using the “OPEN” switch. AD-425S becomes automatic mode. When the connector is N.O. or using the “HOLD” switch, and then change to manual mode. Jumper 1-9 is N.O., or using the “GO” switch. AD-425S becomes manual mode. When the connector is N.C. or using the “PUSH” switch, and then change to automatic mode.
PAGE 6
The opening, closing and maintain -open time illustration table. VM (Opening and Closing Time Adjustment ) Opening and Closing Operating Time Total Opening and Closing Time (VM+ Brake Time) 2 4.5 1 3 6.0 5 5 8.0 10 7 9.5 15 2 4.5 (With high torque output) 20 3 6.0 (With high torque output) 25 5 8.0 (With high torque output) 30 7 9.
PAGE 7
5. Specification 110V (or 220V) AC，50-60Hz Power Input Current (See Figure 2) Torque Opening/Closing time (VM) Maintain - Open time (TC) Battery Specification Temperature Degree of Protection Product Weight 3.5A max., 0.6A average 30Nm 4.5~9.5 s （90°） 1~35 seconds 12V 1.2AH -20℃~+55℃ (Battery 5℃~40℃) IP 12D 6.5 kg Voltage: 8~24VDC Maximum current : 4A Power consumption : 65W Maximum rotation frequency: 2400 RPM 12V=0.15A (Normal); 0.
PAGE 8
Installation instructions z Refer to figure 3 for in-swing door (right-hand). Figure 3 z Opening, Closing action time and Maintain time illustration. AD-425S will be automatically counted the round trip distance and can be adjusted the opening, closing and break time. Figure 4 Opening angle: 90 degrees. Beginning Destination Brake for wall blanking function. VM action time is the opening and closing time. TC Maintain time of 1-35 seconds.
PAGE 9
Figure 5: For right-hand and out-swing door. F/R switch set 「ON」. Operating Arm mounts to left-side. Figure 6: For left-hand and out-swing door. F/R switch set 「1」. Operating Arm mounts to right-side. Figure 7: For right-hand and in-swing door. F/R switch set 「1」. Operating Arm mounts to left-side. Figure 8: For left-hand and in-swing door. F/R switch set 「ON」. Operating Arm mounts to right-side.
PAGE 10
z Figure 11~13 showing an operator installation of a minimum door leaf width and a maximum opening angle. The opening angle is recommended not excess to 120∘. Figure 11 z Figure 12 Figure 13 Figure 14: Automatic door operator dimension Figure 14 z z Install AD-425S on an out-swing door, make sure that the distance between the header and leaf is not more than 60mm, and the space between the header and Sliding Rail mounting hole must be 60mm.
PAGE 11
AD-425S Template Installation Instruction Figure 17 Out-swing door (Right-Hand Open) Figure 18 Out-swing door (Left-Hand Open) Figure 19 In-swing door (Right-Hand Open) Figure 20 In-swing door (Left-Hand Open) Copyright All Rights Reserved. P-MU-AD425S Ver. A Publish:2008.07.
PAGE 12
Installation Steps Step Out-swing door( Right-Hand Open ) Figures Explanation Step 1. Place the AD-425S template to the right position on the door header. See the figure presented for an out-swing door (Right-Hand Open), more details shown in Figure 17. Step 2. Mark for pilot holes. (Use the center pointer) Step 3. Mark six pilot holes, one cable hole and center line. Step 4. Drill a pilot hole. Step 5. Drill six Ø 9.5mm pilot holes and one Ø 18mm cable hole. Step 6. Tap and insert a Blind Nut.
PAGE 13
Steps Figures Explanation Use Allen Wrench to tighten the Blind Nut. This will compress the screw so that it remains permanently fixed in the hole. Repeat these steps on other Blind Nuts. (Do not over tighten the Blind Nut.) Step 7. Blind Nuts Installation illustration Step 8. Blind Nuts installation completed. Step 9. Place the sliding rail template to the right position on the door. See the figure presented for an out-swing door (Right-Hand Open), more details shown in Figure 17. Step 10.
PAGE 14
Steps Figures Explanation Step 12. Use Allen Wrench to tighten the Blind Nut. This will compress the screw so that it remains permanently fixed in the hole. Repeat these steps on other Blind Nuts. (Do not over tighten the Blind Nut.) Step 13. Blind Nuts installation completed. Step 14. Insert two mounting screws. (Screw specification: 6 X 20 mm) Step 15. This is the position of Mounting Hanger. Step 16. Mount the automatic door operator. Step 17. Tighten the other 4 screws.
PAGE 15
Steps Figures Explanation Step 18. Tighten screws. Step 19. Insert screws (6 x 95 mm) to the Operating Arm on Square See the figure presented for a out-swing door (Right-Hand Open), more details shown in Figure 9. Step 20. Tighten nut at other end of screw. Step 21. Use the 10mm wrench to tighten nuts. Step 22. Insert pin to avoid the screws from loosing. Step 23. Slide the Operating Arm to Sliding Rail. Copyright All Rights Reserved. P-MU-AD425S Ver. A Publish:2008.07.
PAGE 16
Steps Figures Explanation Step 24. Fix the Sliding Rail on the door leaf. (Screw specification: 6 X 20 mm) Step 25. Slide in the Sliding Rail Cover. Step 26. Attach two Side Ends. Step 27. Depending on the door leaf opening angle, there may need a Stopper Ball. Step 28. Optional electric lock, wireless push button, microwave sensor, reader and other accessories can be used with the AD-425S operator. See the Control Board guide above on Page 3-5 to wire this application. Step 29.
PAGE 17
Steps Figures Explanation Step 30. First opening movement, the AD-425S will be automatically set the opening angle and distance. Step 31. Attach the cover. Step 32. Attach the Operating Arm cap. Make final settings and adjustments Change battery Copyright All Rights Reserved. P-MU-AD425S Ver. A Publish:2008.07.11 Please refer to page 4~6 for more details of the setting. Battery is located on the back of Control Board.
PAGE 18
Trouble shooting Problem Possible Cause Solution Make sure the Control Board and fuse are working properly and connected properly. No AC power Make sure all motor terminals are connected properly. The door does not respond. Motor have no power (LED motor light not on.) Jumper 1-9, or PUSH Switch Jumper 1-9 is N.O., or using the “GO” switch. AD-425S becomes manual mode. When the setting is incorrect. connector is N.C. or using the “PUSH” switch, and then change to automatic mode.
PAGE 19
Problem Possible Cause Solution The door automatically open but doesn’t close. Safety devices are on Contact your local distributor to check the Photocell and Safety Device. (keep the device clean) “REDA 1”, “REDA 2” contacts Check the “REDA 1”, “REDA 2” contacts are are on. working properly. Remove the obstacles. The door The sensor detects something Check the “REDA 1”, “REDA 2” contacts are automatically opens moving. working properly. Remove the obstacles. and closes by itself.
PAGE 20
General Safety Precautions The following precautions are essential for the user. z Read the precaution below carefully as it contains important information about safe installation and maintenance. z This instruction must be conducted to all potential users. z The product must be used in visible place. z The manufacturer will not be held responsible for any damage caused by improper use of this unit. z Do not use the door closer with the AD-425S.