Users Manual

ManualsBrandsGiant Tech America ManualsElectronicsSmart wireless printing settlement system

Table Of Contents

ZIGBEE-print settlement system

ZIGBEE-print settlement

system

1. Product Overview

1.1 Product composition

1.2 Product introduction

Functions description

Networking

capacity

A host supports up to 16 slave networks, and the 2-bit

dialing on the host can separate the A group, B group, C

group, and D group.In theory, four consoles in the same

ame hall can collect up to 6 4 data from the machine.

The host

communicates

with the

printer

Please dial the printer to 9600 serial communication (you

can press the test button on the printer to call the

corresponding port rate)

Only zigbee host 9600 Brate communication with printer is

supported.Connect the 6P interface provided to the printer

and the zigbee host, dial the code correctly, and the test

page can be printed for 4 seconds by pressing the print on

the Zigbee host.Explain that the host hardware connection

and communication are normal.

Zigbee slave Supports signal acquisition of 2400 and pulse input type of

9600,115200 serial

ort

ort rate.

Codes Host dial:

The first two of the dial switch are to adjust the port rate

The first two of the dial switch are the network ID into A

group, B group, C group and D group

Codes from machine:

The first two of the dial switch are to adjust the port rate

The first two of the dial switch are the slave ID,1~16

Special Note: All dialin

are only re-powered.

Summary of content (10 pages)

PAGE 1
system ZIGBEE-print settlement 1. Product Overview 1.1 Product composition 1.2 Product introduction Functions Networking capacity description A host supports up to 16 slave networks, and the 2-bit dialing on the host can separate the A group, B group, C group, and D group.In theory, four consoles in the same game hall can collect up to 6 4 data from the machine.
PAGE 2
Network lights Network Description of the host operating interface From the machine button Description Host: The green led lamp is often turned off on the host standby.After the host increases the slave device, the led is often bright for 4 minutes, allowing the slave device to join the host for data acquisition. From the machine: After connecting the host, the green light always shines, the line or the distribution network often extinguished.
PAGE 3
NET: The slave network online indicator light.Only this light on shows that the slave is connected to the host.(The test page of the slave can be printed by pressing the Print on the slave for 4 seconds.To show whether the network is smooth) Host OLED interface Host: (separately out to write operation instructions) 1. display time and ticket information scroll display (the content of the scroll bar can be changed to the serial port location address or the desired settlement system name) 2.
PAGE 4
A diagram host operating interface B diagram of slave operation interface 1.3 Product operation instructions 1.3.
PAGE 5
Host long press set button 3S after let go, see the Network green light on the host for 4 minutes, short press set, from the machine to see the green light, the network is successful. 1.3.2 print test The dialing code on the printer goes to 9600 , and the host also 。 Power the host.If the host can press the Print button, goes to 9600 and the test page can print that the host power supply and communication meet the conditions.
PAGE 6
Project Set the scroll bar Directive format rolling “abcde(any word)” Set time Set the password time 2021 9 22 14 11 56 password 1 2 3 4 Description Be sure to have quotation marks The password is 1 2 34 1.4 Description of the host OLCD screen interaction interface 1.4.1 LCD interaction interface description: After turning on, enter the first main interface as follows: scroll to show the ticket settlement system, (ticket settlement system is only tentative content, entry is actually the address.
PAGE 7
1.4.4 After pressing the set button for settling all interface options, enter the selected print time period below.The settlement flow of the bill is to summarize all lines after 11:59 p. m.Time arranges storage before and back.In theory, the space can save the data for about 1 month. 1.4.5 After pressing the set button in the setting time interface, enter the annual date and time setting. After losing the minutes, the data will be returned to the main interface.
PAGE 8
1.4.7 In the factory setting interface, enter the administrator password after entering the set button. The main purpose is to clean up all the data, login password to the original 0000, and the address to the original ticket settlement system.(Restore factory can also be sent through the computer serial command to reset) the administrator password is correct or wrong will be prompted. 1.4.8 All operating interfaces, if not at the main interface, return to the main interface after 30 seconds. 1.
PAGE 9
1.6 Fault inspection Whether the host's telephone interface with the printer is normal, whether the host short press print can hit the test page on the printer. Whether the slave can join the network, whether the slave network indicator light is on.You can test for normal communication by printing the slave test page. If they are imported, you can restore the factory setting through the host, restore the factory setting from the machine and then test products.
PAGE 10
FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.