User's Manual
Table Of Contents
- Connecting the Base Station and Power Plug
- Connecting the Charging Station #
- Install and Charge the Batteries
- Place the handset in the base station to charge for 16 hours prior for first use. If you don’t properly charge the phone, battery performance will be compromised.
- Using the Handset Telephone
- Selecting the Language
- Making Internal Calls
- Making External Calls
- Taking Calls
- Redialling
- The phone stores the last ten numbers dialled in the redial memory.
- Press key; the last call number dialled is displayed.
- Press or key to search the required number in the redial memory list.
- Press key to carry out the conversation.
- Press key to end the call.
- Note: 1. If the number is longer than 16 digits, only the last 14 digits will be shown.
- 2. Name is displayed instead if number is matched with phone book memory.
- Dialling from the Phone Book
- Call Log Operations
- Browse, Call Back, Delete, Store
- Press to enter CALL LOG memory.
- Browse: Press or key to browse through the CALL LOG memory.
- Call Back: press or key to call back.
- Or
- Press to select DELETE? by using or key.
- Or
- Press to select DELETE ALL? by using or key.
- Or
- Store: Press to enter CALL LOG menu.
- Press to select SAVE NUMBER by using or key.
- Press key to save the entry in phone book memory.
- Press 0-9 to add digits in front of CLI number.
- Press to remove entry or leftmost digit.
- Press or key can recover the original CLI number.
- Example:
- Holding Calls /Forwarding Calls
- Intercom Call Transfer
- Teleconference
- Press and enter the number of the corresponding handset (e.g.2) which will join the teleconference.
- The external caller is kept on hold. As soon as handset 2 takes the call, the internal connection is established.
- Press the key any time, and then press or key scroll to “CONFERENCE”.
- Press will start the 3 way conference.
- Press again, “SINGLE CALL” will show and then press will end the 3 way conference and return to intercom call.
- Note: The handset which initiates the intercom call can switch between the phone call and the intercom handset by pressing key and then press or key to select “SWITCH”.
- By pressing the key, any of the handsets can quit from the teleconference and the other handset continues with the external call.
- Handset Speaker Phone
- Changing the Receiver Volume
- Muting the Ringer volume
- Muting the Microphone
- Paging the Handset
- Entering a Dialling Pause (P)
- Switching the Key Lock On/Off
- Incoming calls can still be received when key locked.
- Press key to access phone book memory.
- Press key to access phone book menu.
- Press or key to select ADD NEW and press key.
- Enter number (max. 24 digits) and press key when finished.
- Enter name (max. 15 characters) and press key when finished.
- Press key to access phone book memory.
- Edit Entry: Press or key to scroll.
- Press key to select a desired entry, and then press or to select the submenu EDIT.
- Press to start Number edition and press key again to start Name edition.
- Press key to confirm.
- Note: Press key to delete any incorrect input.
- Or
- Delete: Press or key to scroll.
- Press key to select a desired entry, and then press or to select the submenu DELETE?.
- Press key to delete the entry.
- Press key again to confirm.
- Changing the Handset Ringer Melody
- Changing the Ringing Volume
- Activating/Deactivating Automatic Call Answering
- Setting the Alarm
- Entering/Changing Handset Name
- Changing the Base Ringer Melody (external / internal)
- Changing the Ringing Volume
- Changing Base PIN Code
- Changing the Dialling Mode
- Changing the Flash Time
- VMWI
- Setting the Area Code
- Reset Base
- Date / Time
- Registration
- Registering Additional Handsets
- Remove a Handset from the Base
- Press key until the REGISTRATION menu appears and press key.
- Press or key to select the submenu REMOVE HANDSET and press key.
- Enter the PIN (factory setting =0000) and press key
- If necessary, use or key to select the handset and press key. REMOVE HANDSET? will show on the display.
- Press key to confirm.
- For guidance only, depends on initial battery charge.
- Consumer Information
Press key to confirm the setting.
Default Settings
This option allows user to restore the cordless handset to the default
setting.
1. Press key.
2. Press
or key to select SETUP HS and press
key.
3. Press
or key to select RESET and press key,
the LCD will display RESET?.
4. Press key to confirm the setting.
Base Station Settings (using the
Handset)
Changing the Base Ringer Melody (external /
internal)
You may select one of the 5 available base ringer tones for your
incoming calls alert tone.
Press key.
Press
or key to select SETUP BS and press
key.
Press
or key to select RING MELODY and press
key.
Press or key to select the desired ring melody, the
selected melody will be sounded.
Press key to confirm the setting.
Changing the Ringing Volume
You may select one of the 5 available volumes for your incoming
calls alert tone.
Press key.
Press
or key to select SETUP BS and press
key.
Press
or key to select RING VOLUME and press
key.
Press
or key to select the desired ring volume (0-5),
the selected volume will be sounded.
Press key to confirm the setting.
Changing Base PIN Code
PIN is your base’s identification number, the function is to avoid the
setting changed by others. The default setting is “0000”. You may
change the PIN. Please take down the change so as to operate the
unit normally.
Press key.
Press or key to select SETUP BS and press
key.
Press
or key to select CHANGE PIN and press
key, the LCD will show ENTER PIN.
Press number key to input the old PIN code and press
key,
the LCD will show NEW PIN, prompt you to input a new PIN
code.
Note: WRONG PIN will be shown if the old PIN code you input is
wrong, and then return to step 4.
Input the desired new PIN code and press
key, the LCD
will show REPEAT PIN, prompt you to input the new PIN code
again.
Input the new PIN code again and press
key to confirm
the setting.
Note: 1. The PIN code must be 4 digits.
2. If the new PIN code that you input two times is different, the
change will fail, the display will return to step 5.
Changing the Dialling Mode
You may set the dial mode to TONE or PULSE according to your
– 13 –