User's Manual
Table Of Contents
- Connecting the Base Station and Power Plug
- Connecting the Charging Station #
- Install and Charge the Batteries
- Place the handset in the base station to charge for 16 hours prior for first use. If you don’t properly charge the phone, battery performance will be compromised.
- Using the Handset Telephone
- Selecting the Language
- Making Internal Calls
- Making External Calls
- Taking Calls
- Redialling
- The phone stores the last ten numbers dialled in the redial memory.
- Press key; the last call number dialled is displayed.
- Press or key to search the required number in the redial memory list.
- Press key to carry out the conversation.
- Press key to end the call.
- Note: 1. If the number is longer than 16 digits, only the last 14 digits will be shown.
- 2. Name is displayed instead if number is matched with phone book memory.
- Dialling from the Phone Book
- Call Log Operations
- Browse, Call Back, Delete, Store
- Press to enter CALL LOG memory.
- Browse: Press or key to browse through the CALL LOG memory.
- Call Back: press or key to call back.
- Or
- Press to select DELETE? by using or key.
- Or
- Press to select DELETE ALL? by using or key.
- Or
- Store: Press to enter CALL LOG menu.
- Press to select SAVE NUMBER by using or key.
- Press key to save the entry in phone book memory.
- Press 0-9 to add digits in front of CLI number.
- Press to remove entry or leftmost digit.
- Press or key can recover the original CLI number.
- Example:
- Holding Calls /Forwarding Calls
- Intercom Call Transfer
- Teleconference
- Press and enter the number of the corresponding handset (e.g.2) which will join the teleconference.
- The external caller is kept on hold. As soon as handset 2 takes the call, the internal connection is established.
- Press the key any time, and then press or key scroll to “CONFERENCE”.
- Press will start the 3 way conference.
- Press again, “SINGLE CALL” will show and then press will end the 3 way conference and return to intercom call.
- Note: The handset which initiates the intercom call can switch between the phone call and the intercom handset by pressing key and then press or key to select “SWITCH”.
- By pressing the key, any of the handsets can quit from the teleconference and the other handset continues with the external call.
- Handset Speaker Phone
- Changing the Receiver Volume
- Muting the Ringer volume
- Muting the Microphone
- Paging the Handset
- Entering a Dialling Pause (P)
- Switching the Key Lock On/Off
- Incoming calls can still be received when key locked.
- Press key to access phone book memory.
- Press key to access phone book menu.
- Press or key to select ADD NEW and press key.
- Enter number (max. 24 digits) and press key when finished.
- Enter name (max. 15 characters) and press key when finished.
- Press key to access phone book memory.
- Edit Entry: Press or key to scroll.
- Press key to select a desired entry, and then press or to select the submenu EDIT.
- Press to start Number edition and press key again to start Name edition.
- Press key to confirm.
- Note: Press key to delete any incorrect input.
- Or
- Delete: Press or key to scroll.
- Press key to select a desired entry, and then press or to select the submenu DELETE?.
- Press key to delete the entry.
- Press key again to confirm.
- Changing the Handset Ringer Melody
- Changing the Ringing Volume
- Activating/Deactivating Automatic Call Answering
- Setting the Alarm
- Entering/Changing Handset Name
- Changing the Base Ringer Melody (external / internal)
- Changing the Ringing Volume
- Changing Base PIN Code
- Changing the Dialling Mode
- Changing the Flash Time
- VMWI
- Setting the Area Code
- Reset Base
- Date / Time
- Registration
- Registering Additional Handsets
- Remove a Handset from the Base
- Press key until the REGISTRATION menu appears and press key.
- Press or key to select the submenu REMOVE HANDSET and press key.
- Enter the PIN (factory setting =0000) and press key
- If necessary, use or key to select the handset and press key. REMOVE HANDSET? will show on the display.
- Press key to confirm.
- For guidance only, depends on initial battery charge.
- Consumer Information
For guidance only, depends on initial battery charge.
General Product Care
Simply wipe the base station with a damp cloth or an antistatic wipe.
Never use a dry cloth as this can cause static discharge.
Periodically clean the charge contacts on the handset and base
and charger with a soft cloth.
Troubleshooting Guide
PROBLEMS CAUSES SOLUTIONS
Registration not
work.
The battery is not
sufficiently charged.
Handset and base
station were not
prepared for
registration.
Charge the battery for
14 hours (see Battery
Charging).
Unplug and then plug
in the power adaptor.
No display. The battery has not
been charged.
Charge the battery or
replace them (see
Battery Charging)
No reactions to
keystroke.
No radio
connection to the
base station:
blinking!
The keypad is locked.
The handset is
outside the base
station range.
The handset is not
registered.
The base station does
not work.
Press
key longer
than 2 seconds.
Move closer to the
base station.
Register the handset
(see Registering
Handset).
Unplug and then plug
the power adaptor to
the power outlet
(220-230V AC / 50
Hz) and the other end
into the power jack on
base bottom.
Consumer Information
1. An applicable certification jacks Universal Service
Order Codes (USOC) for the equipment is provided
(i.e., RJ11C) in the packaging with each piece of
approved terminal equipment.
2. If this equipment causes harm to the telephone network,
the telephone company will notify you in advance that
temporary discontinuance of service may be required.
But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible.
Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
3. The telephone company may make changes in its
facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this
happens the telephone company will provide advance
notice in order for you to make necessary
modifications to maintain uninterrupted service.
4. Please follow instructions for repairing if any (e.g.
battery replacement section); otherwise do not alternate
or repair any parts of device except specified.
5. Connection to party line service is subject to state tariffs.
Contact the state public utility commission, public
– 16 –