Instructions / Assembly

Remove old gutters and inspect fascia board and metal drip edge, repair or replace the

fascia/drip edge if needed. Tack a string to the fascia board 4 or 5 inches below the rooine

so that it is straight, level and taut. Drop one end of the string 1/4 inch per 10 ft., sloping

toward downspout.

DOWNSPOUT

1. Preparation: Measure and mark with a chalk line

Begin assembling your gutter system on the ground starting at end furthest from the down-

spout. Adhere an end cap to the rst piece of gutter, then join gutter sections using slip connec-

tors secured with screws or pop rivets.

Waterproof all joins with sealant, and secure with screws or pop rivets.

2. Assemble Gutter Sections

3. Hang Gutters onto the Fascia

4. Attach Mitres, Drop Outlets and Downspouts

Spike & Ferrule Insert ferrule into gutter lined

up with a rafter, hammer spike through gutter

and drip edge into the fascia.

Hidden Hanger Hook the hanger under the

front lip of the gutter. Drive a nail or screw

through the hole in the hanger into the fascia.

Strap Hanger Hook the hanger under the front

lip of the gutter. Carefully lift shingles then nail

into the roof deck.

Locate and mark the end of each rafter on the fascia board (Typically 24 inches). Use one of the following methods to hang your

gutter. Be sure that the drip edge hangs into the gutter and not behind it.

Attach mitres to fascia board at the corners. Connect mitres to gutter with slip connectors. Secure

with screws or pop rivets. Apply sealant to the inside seams to protect against leaks.

Connect elbows (a) and downspout (b) with the crimped ends pointing down. Secure the joints

with screws (c). Attach the downspout to the outlet then attach an elbow at the bottom to direct

rainwater away from the foundation.

Fasten downspout snugly to the wall with downspout bands.

Use 2 downspout bands for each 8-10 foot section of downspout.

SEALANT

HANGERS

Gutter material has sharp edges. Always use leather gloves and eye protection.

Working above grade is inherently dangerous, observe OSHA Regulations, Fall

Protection Systems Criteria and Practices (1926.502).

SECURE

AND SEAL

CONNECTOR

#RJ3FHA-SP

STEEL FASCIA GUTTER

INSTALLATION GUIDELINES

These basic installation guidelines are for use with typical or standard applications. It is always recommended to seek advice from a licensed

professional, and to check with your local building inspector or building permit office for approvals and possible variations that may apply.

PAGE 1
INSTALLATION GUIDELINES STEEL FASCIA GUTTER #RJ3FHA-SP 1. Preparation: Measure and mark with a chalk line Remove old gutters and inspect fascia board and metal drip edge, repair or replace the fascia/drip edge if needed. Tack a string to the fascia board 4 or 5 inches below the roofline so that it is straight, level and taut. Drop one end of the string 1/4 inch per 10 ft., sloping toward downspout. OUT NSP W DO 2.
PAGE 2
PAUTAS DE INSTALACIÓN BÁSICA CANALETA DE ACERO PARA TABLA FRONTAL #RJ3FHA-SP 1. Preparación: Medir la distancia con un cordel entizado 1. Retire las canaletas antiguas y revise la tabla frontal; repárela si es necesario. Fije una cuerda a la tabla frontal y establezca una línea de nivel. Baje la cuerda 2,54 cm cada 12 m, con inclinación hacia el bajante pluvial. S N TE A J BA 2. Montar las secciones del desagüe 2. Comience en el extremo más alejado del bajante pluvial.