Step 11. If you select the “Dynamic IP Address” in the WAN TYPE SELECT, the following screen will appear. First, select “Automatic” or “Manual” DNS. Please key in the Host Name and Manual DNS IP address if you select “Manual” DNS. Press “Finish” to go to next step. Step 12. After “Reboot” is pressed, it proceeds with the next step.
Step 13. Please wait a moment. Step 14. The IE browser will be automatically connected to the main menu, and the setup is completed by then. Please use your IE connect to Internet. If you can connect to the Internet , the setting is completed. If you use the Wireless Lan Card connection , please continue to section 3-4 Wireless Basic Setting.
Step 15. If you select “Static IP Address” in the WAN TYPE SELECT, please key in the data provided by the wideband company in the following fields as shown below: Note: a. If your wideband company gives you more than one IP address, then select one of them to fill in the column in the above figure, and refer to Appendix A for the use of other IP addresses. b. Static IP Setup Normal Users please use "NAT enable" then connect to Internet in general. Step 15.
Step 16. Please wait for a moment. Step 17. The IE browser will be automatically connected to the main menu, and the setup at the PC end is completed by then. Please use your IE connect to Internet. If you can connect to the Internet , the setting is completed . If you use the Wireless Lan Card connection , please continue to section 3-4 Wireless Basic Setting.
Step 18. If you select “PPP(Modem)” in the WAN TYPE SELECT, please key in the data provided by the ISP company in the following blanks , then click “finish” , shown as below: Step 19. After “Reboot” is pressed, it proceeds with the next step.
Step 20. Please wait for a moment. Step 21. The IE browser will be automatically connected to the main menu, and the setup at the PC end is completed by then. Please use your IE connect to Internet. If you can connect to the Internet, it means you have finished the setting. If you use the Wireless Lan Card connection, please continue to 3-4 Wireless Basic Setting.
3-4 Wireless Basic Setting Step 1. Please key in the data. Region Because of the different region has different open channel regulations, please choose your local area, system will change to your local area utilize channel list automatically. Channel Please choose the Channel where you at, different area has different channel range, the default value is channel 6.
Step2. “MAC Access Control” shown as the diagram. You can set up either “allow” or “deny” the user can connect to the Internet by setting the MAC address. Default Rules : Disable/Allow/Deny Disable : Disable MAC Address control. Allow : The user can connect to the Internet. Deny : The user cannot connect to the Internet. The format of MAC address is XX:XX:XX:XX:XX:XX.(exp.
Step3. Please wait for a moment. Step4. After the Wireless Basic setting is completed, check the status of the WAN connection. If the status is “connect” then you can use IE to the Internet, else please click the “connect” bottom to reconnect.
3-5 Logout After you finish GN-BR402W setup, please choose “ Logout”. Note : After 5 minutes idle time, the system will be automatically logout.
4. Status -“ Status” screen shows the current basic network setting status . Status 1. If you select “PPPoE” in the WAN TYPE SELECT, press “Status”, and the screen shows as follows: Note: your network service provider automatically obtains each of the above IP address at the WAN end. Status 2. If you select “Dynamic IP Address” in the WAN TYPE SELECT, press “Status” screen as follows: Note: your network service provider automatically obtains Each IP address of the above WAN end.
Status 3. If you select “Static IP Address” in the WAN TYPE SELECT, press “Status”, and the screen shows as follows: Status 3.
5. Change Password - Key in your old password, and key in your new password. After your confirmation, key in your new password once again, and the procedure will complete after you press: “Submit”.
6. Change MAC address -If your ISP Company asks you to use the original MAC address. You can enter your MAC address at this place. PS: MAC address is from your NIC that you registered with your ISP Company. If you want to restore to the factory default, please use “reset MAC” from GN-BR402W install CD.
7. Firmware Upgrade - Please browse and select your desired upgrade file (firmware version), and press upgrade. Note: you can download the upgraded firmware version from Gigabyte website. Please wait a moment, and the IE browser will be automatically connected to the main menu, and the setting of our firmware upgrade is completed.
8. Instruction of Using Special Application When special application program users at the LAN end want to use a certain network application program, such application program needs more set up than the regular connection, and most of these application programs are games or audio/video multimedia. Take AOK (Age of Kings) for example : - Application: AOK - Trigger Port : 47624 - Other Ports: 2300 2400,28800 29000 - Enable: enable 1.
8-1 Instruction of Using DMZ If we do not know how to set up certain game or software or the field for set up cannot satisfy the need, then the virtual IP Address (such as 192.168.1.1) obtained the PC at the LAN terminal can be used to input to the field of DMZ. Taking NetMeeting for example, if you just want to call an external computer from the computer at the LAN terminal, it does not need any set up.
8-2 Instruction of Using Netmeeting 1. If we need to actively call the PC of the external network from the PC at the LAN terminal, it 2. does not need special set up. To let a PC at the WAN end call a PC at the LAN end, set the virtual IP Address (such as 192.168.1.1) of the PC at the LAN end to the DMZ field in the Special Application as shown in the following figure. The PC at the WAN end can call the external IP Address (provide by the ISP) of the BR402W, and the internally connects to such PC.
9. Instruction of Using the Virtual Server Virtual server provides a way to let the PC at the WAN end connect to a server of a PC at the LAN end. Taking the IP Address 192.168.1.1 of a PC on a FTP (port:21) at the LAN end for example: Port: 21 Virtual Server IP: 192.168.1.1 Enable: enable The PC at the WAN end can connect to the internal FTP server at the IP address 192.168.1.1 via the WAN end of the IP Address of the FTP BR402W.
10. VLAN VLAN is using for 4 LAN ports that can be divided into maximum four different virtual LANs. Although each different virtual LAN user’s IP is in the same subnet, however the communication between each other will be limited. This function is for dividing the user in the same subnet, usually provided for high-end switch.
11. Static Routing Table Under some of Internet environments, some of the subnet do not go through the default gateway. Users can add those routing information to Static Routing Table by themselves. You can enter new routing information and click “Add new to Static routing” then there will add the new routing information to Static Routing Table.
12. Troubleshooting Q: What to do if you forget your password or forget the IP address of the GN-BR402W? Please press the “Reset” bottom on the GN-BR402W about 4 sec. The GN-BR402W will be restart and the system setting will restore to default value. Q: Unable to connect to Internet? n Please confirm whether or not the power cord is properly connected, and the power indicating light of the GN-BR402W is normal.
13.
(B) USB Driver Installation Preface 1. Before installing the USB driver, please refer to Section 3-2 for the installation at your PC end. If “obtain an IP address automatically” is not selected in the installation at your PC, then you should know the following information: IP address ranges from “192.168.2.1” to “92.168.2.252” Subnet Mask “255.255.255.0” Default Gateway “192.168.2.253”. 2. Follow the “Found New Hardware Wizard” to complete the GN-BR402W USB Driver Installation.
Please choose “Search for a suitable driver for my device (recommended)”, and then press “Next” for next step. Please choose the location where you place the GN-BR402W Driver , and then press “next”.
Please click “Next” for next step. Please click “Yes” for next step.
Please click “Finish” for next step. Please click “Yes”. NOW YOU HAVE COMPLETED THE USB DRIVER INSTALLATION.
(C) Instruction of Printer Server The GN-BR402W Wireless Broadband Router can be as a Printer Server, Please follow the setup procedure in Printer Setting. Example as follow: Start > Setting > Printer, Double-Click Add Printer. The Add Printer Wizard dialog will be displayed, please select the Local Printer option and press “Next”. Select Create a new port option, Type: “Standard TCP/IP Port” then press “Next”.
Press “Next”. Please enter the Printer Name or IP Address : 192.168.1.254 and the Port Name : IP_192.168.1.254, Press “Next”.
The Device Type selects Custom option and press “Setting”. The Configure Standard TCP/IP Port Monitor dialog will be displayed. Enter the Port Name : IP_192.168.1.254 and Printer Name or IP Address is 192.168.1.254. Select the LPR Protocol and enter the Queue Name : lp and select the LPR Byte Counting Enabled check box in the LPR setting then press “OK”. Press “Finish”.
Select the manufacturer and model of your printer. (If your pr inter is not listed, click “Have Disk ” to install your printer driver.) Click “Next”, the wizard will help you finish the installation automatically.
Limited Warranty 1-Year Warranty Gigabyte warrants to the original consumer/purchaser that the adapter product free from defects in material and workmanship for no limited time from the original manufactory shipment date. This warranty does not cover the adapter product if it is damaged in the process of being installed or improperly used. Gigabyte may replace or repair the adapter product with either new or reconditioned parts.
Safety, Care and Regulatory Information Important safety instructions Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. The product should be operated only from the type of power source indicated on the rating label. If your computer has a voltage selector switch, make sure that the switch is in the proper position for your area.
Federal Communications Commission (FCC) Statement NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
