GN-WI01GS MINI PCI Wireless Adapter User’s Manual http://www.gigabyte.com.tw Revised 1.
Administrative Regulations on Low Power Radio Waves Radiated Devices Article 14 Without permission granted, the frequency change, transmitting power enhance or alter of original design characteristic as well as function by companies, enterprises, or users for approved Low-power radio frequency devices is not allowed.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
Content CHAPTER 1 PRODUCT OVERVIEW .............................1 1-1. INTRODUCTION ..........................................................................................................................1 1-2. F EATURES .................................................................................................................................1 1-3. P HYSICAL DIMENSIONS /PACKAGING ........................................................................................1 1-4. LED INDICATOR ............
Chapter 1 Product Overview 1-1.Introduction This 802.11b/g Wireless Local Area Network (WLAN) card is composed of Media Access Controller (MAC), baseband, radio components, MINI-PCI interface, and one external antenna. It operates within the 2.4GHz spectrum, providing high speed (up to 54Mbps) and secure (supporting AES, 802.1x & WEP and WPA) WLAN connections. 1-2.Features n n n n n n n Conforms to 802.11b/802.
1-4.LED Indicator ACT LINK Meaning OFF OFF Network card is not functioning ON ON Network card is connecting to network LED Condition of the Receiver ACT LINK 1-5.System Requirements 1-5-1. Supported Platform: IBM PC/AT compatible computer 1-5-2. Supported Operation System: Windows 98SE/Me/2000/XP 2 ON BLINK Network card is sending/receiving data.
Chapter 2 Installing the WLAN Card The following sections will assist you to install this WLAN card. 2-1: Hardware Installation, 2-2~2-5: Software Installation, which provides users more convenient installation methods and automatically installs drivers and utilities. Please refer to different section (2-2: Windows 98SE, 2-3: Windows ME, 2-4: Windows 2000, and 2-5: Windows XP) for software installation in accordance with your operation system. 2-1.
2-2. Installing The Driver & Utility (Win 98SE) Step 1: Click “Cancel” for automatic installation. Step 2: Insert the installation CD into the CD-ROM drive. The following window will pop up. Step 3: Click “Install Wireless LAN Utility”.
Step 4: Click “Next”. Step 5: Click “Next”.
Step 6: Click “OK”. Step 7: Click “Finish”. Step 8: To install 802.1X authentication function, click “Browse the CD”.
Step 9: Run “CD-ROM:\\Utility \AegisI2.exe” of the installation CD. Step 10: Click “Install”. Step 11: Click “Cancel”. Windows may reboot after the installation.
2-3. Installing The Driver & Utility (Win ME) Step 1: Click “Cancel” for automatic installation. Step 2: Insert the installation CD into the CD-ROM drive. The following window will pop up. Step 3: Click “Install Wireless LAN Utility”.
Step 4: Click “Next”. Step 5: Click “Next”.
Step 6: Click “OK”. Step 7: Click “Finish”. Step 8: To install 802.1X authentication function, click “Browse the CD”.
Step 9: Run “CD-ROM:\\Utility \AegisI2.exe” of the installation CD. Step 10: Click “Install”. Step 11: Click “Cancel”. Windows may reboot after the installation.
2-4. Installing The Driver & Utility (Win2000) Step 1: Click “Cancel” for automatic installation. Step 2: Insert the installation CD into the CD-ROM drive. The following window will pop up. Step 3: Click “Install Wireless LAN Utility”.
Step 4: Click “Next”. Step 5: Click “Next”.
Step 6: Click “OK”. Step 7: Click “Finish”.
Step 8: Click “Yes”. Step 9: To install 802.1X authentication function, click “Browse the CD”.
