Blue Eye VGA Water Block GH-WPBV1 Rev.
English Table of Contents Caution................................................................................................................................................3 Product Appearance Introduction........................................................................................................4 Product Specifications.........................................................................................................................4 Feature Summary ..................................
English Caution 1. Before refilling the tank with coolant for testing the Liquid cooling system, please make sure again that all water tube joints are securely fitted and the clips are correctively positioned. 2. While removing water tubes for uninstallation, be sure to keep the device for removal of these tubes away from any electronic part. The following are not covered by the warranty: 1. Use the product incorrectly or in a manner other than the designed purpose. 2.
English Product Appearance Introduction Product Serial Number: Model: Dimensions: Materials: Flow Meter: ATi CrossFire Supported: nVidia SLi Supported: GPU Compatibility: Inlet Outlet Product Specifications Base Blue Eye VGA Water Block GH-WPBV1 113 x 61.5 x 40.5 mm Cooper, PC Cover Yes (UV Reaction) Yes Yes Please refer to Page 6; 1-2 Hold-Down Plates Introduction Feature Summary 1. 2. 3. Please make sure that the protective film is removed before use.
English Component List (1) 1/4” tube x 1 GH-WPBV1 VGA Water Block (9) Screws x 4 (10) Spring loaded screws x 4 (15) Grease (16) User manual (2) RAM heatsinks x 16 (3) 1/2” tube clamps x 4 (4) 3/8” tube clamps x 4 (5) 1/4” tube clamps x 10 (6) 1/2” tube splitters x 2 (7) 3/8” tube splitters x 2 (8) 1/4” tube splitters x 2 (11) Hold-down plates (12) Base plate (13) Washers x 4 (14) Wrench 5
English I. Hardware Installation 1-1 VGA Fan Disassembly Please disassemble the fan on the VGA Card on your own. 1-2 Hold-Down Plates Introduction There are three combinations for the hold-down plate installations. Type A (Factory Default) Type A supports the following VGA Cards. PCIE nVIDIA ATI 7900 X1900 7800 X1800 6800 6 AGP nVIDIA ATI 6800 Type B Type B supports the following VGA Cards.
English Type C Take Type B for example. As shown in Fig. a, place the disc hold-down plate with the engraved Gigabyte logo facing up, so that the mounting holes on the disc hold-down plate match with the mounting holes on the base plate, and secure it with a fastener (as shown in Fig. a). Type C supports the following VGA Cards.
English 1-4 Water Block and VGA Card Installation Apply the grease on the VGA chipset as shown in Fig. c. Insert the screws on the water block into the mounting holes as shown in Fig. d. Place the base plate (Component 12) in the desired position as shown in Fig. f. Fig. f Bolt the base plate using the supplied spring loaded screws (Component 10) as shown in Fig. g. As shown in Fig.
2-1 Water Tube Installation for Single VGA Card Please follow the procedures shown on the diagram on the left to proceed with the installation for single VGA card. The water-cooling system used in the example is Gigabyte 3D Galaxy. Procedure 1: Cut the supplied water tube connected to the radiator and CPU water block and the supplied water tube connected to the CPU water block and pump.
English 2-2 Water Tube Installation for Dual VGA Card Procedure 1 and 2: Same as in the water tube installation for single VGA card. Procedure 3: Connect one end of the supplied 1/4” water tube (Component 1) to the supplied 1/2” splitter (Component 8) and the other end to the VGA water block 1 inlet. Connect the VGA water block 1 outlet and the VGA water block 2 inlet with another supplied 1/4” water tube (Component 1).
English III. Overview of Installed Water Block Please make sure the VGA water block 1 is installed on top of the VGA water block 2.
English
