User's Manual

ManualsBrandsGIGABYTE ManualsMotherboardsGIGABYTE GA-6WMMC7

R-21-01-091213

6WMMC7 Series

USER'S MANUAL

1. Support Suspend To RAM Function.

2. Support Hardware Monitor.

3. System power on by PS/2 Mouse: First, enable this function

in CMOS Setup, then you can power on the system by double

clicking the right or left button of your PS/2 Mouse.

4. System power on by Keyboard: If your ATX power supply

supports larger than 300 mA 5V Stand-By current (depends

on the specification of keyboards), you can power on your

system by entering password from the Keyboard after setting

the “Keyboard power on” jumper and password in CMOS

Setup.

5. Support 3 steps ACPI LED selectable.

6. Support Modem Ring-On (Include internal Modem and

external modem on COM A).

7. Support Wake-up On LAN (Your ATX power supply must

support larger than 720 mA 5V Stand-By current).

8. Built-in AC97-Link software audio.

9. Support Audio / Modem Riser (AMR) interface.

10. Support TV/DFP(Digital Flat Panel) function by TV/DFP

daughter card (Optional).

11. Aureal AU8810 Hardware Audio (Optional).

Socket 370 Processor MAIN BOARD

REV. 2.1 First Edition

Summary of content (108 pages)

PAGE 1
6WMMC7 Series USER'S MANUAL 1. Support Suspend To RAM Function. 2. Support Hardware Monitor. 3. System power on by PS/2 Mouse: First, enable this function in CMOS Setup, then you can power on the system by double clicking the right or left button of your PS/2 Mouse. 4.
PAGE 2
PAGE 3
6WMMC7 Series The author assumes no responsibility for any errors or omissions that may appear in this document nor does it make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Dec.
PAGE 4
Quick Installation Guide I. Quick Installation Guide : CPU SPEED SETUP The system bus frequency can be switched at 66MHz / 100MHz / 133MHz and Auto by adjusting JP5,JP23. The CPU ratio is control by BIOS. 0 The CPU speed must match with the frequency ratio. It will cause system hanging up if the frequency ratio is higher than that of CPU. 0Note: Please set the CPU host frequency in accordance with your processor’s specifications.
PAGE 5
6WMMC7 Series II. Jumper Setting : GN : Green Function Switch AC97 CPU AU 8810 FWH32 GMCH/ PIN No. Function 82810 / Open Normal Operation 6WMMC7 810E Short Entering Green Mode ICH/ 82801 GD : Green Function LED AC97 CPU AU 8810 − ICH/ FWH32 + 1 82801 PIN No.
PAGE 6
Quick Installation Guide HD : IDE Hard Disk Active LED AC97 CPU AU 8810 1 + FWH32 ICH/ 82801 − GMCH/ PIN No. Function 82810 6WMMC7 1 LED + 2 LED − SPKR: External Speaker Connector AC97 CPU AU 8810 FWH32 PIN No.
PAGE 7
6WMMC7 Series J9: Buzzer Enable (Optional) AC97 CPU AU 8810 PIN No. Function Open Internal Buzzer Disable GMCH/ 82810 6WMMC7 Close Internal Buzzer Enable ICH/ FWH32 82801 RES : Reset Switch AC97 CPU PIN No.
PAGE 8
Quick Installation Guide PWR : Power LED Connector (as 3 steps ACPI LED) AC97 CPU AU 8810 + 1 FWH32 − PIN No. 1 6WMMC7 2 3 − ICH/ 82801 Function LEDGMCH/ + 82810 LED − LED − PW: Soft Power Connector AC97 CPU AU 8810 FWH32 ICH/ 82801 PIN No.
PAGE 9
6WMMC7 Series IR : Infrared Connector (IR / CIR) AC97 FWH32 PIN No. 1 2 3 4 5 6 7 ICH/ 8 82801 9 10 Function VCC 1 CPU 6 NC AU 8810 IRRX GND IRTX NC 6WMMC7 CIRRX VCC 5 NC NC GMCH/ 82810/ 810E 10 PS/2 Mouse / Keyboard Connector AC97 PS/2 Mouse 6 4 FWH32 ICH/ 82801 AU 8810 PS/2 Mouse/ Keyboard Pin No.
PAGE 10
Quick Installation Guide USB : USB Port AC97 5 6 7 8 AU 1 2 388104 PIN No. 1 2 3 4 5 6 7 8 Function USB V0 USB D0USB D0+ GND CPU USB V1 USB D1USB D1+ GND GMCH/ 82810/ 810E 6WMMC7 ICH/ FWH32 82801 CPU FAN : CPU Cooling Fan Power Connector AC97 1 AU 8810 PIN No.
PAGE 11
6WMMC7 Series POWER FAN : Power Cooling Fan Power Connector AC97 CPU AU 8810 1 6WMMC7 FWH32 ICH/ 82801 PIN No. 1 GMCH/ 2 82810 3 Function GND +12V SENSE SYSTEM FAN : System Cooling Fan Power Connector AC97 CPU AU 8810 1 FWH32 ICH/ 82801 PIN No.
PAGE 12
Quick Installation Guide IDE1: Primary IDE Port AC97 CPU AU 8810 GMCH/ 82810/ 6WMMC7 FWH32 810E ICH/ 82801 1 IDE2: Secondary IDE Port AC97 CPU AU 8810 GMCH/ 82810/ 810E 6WMMC7 FWH32 ICH/ 82801 1 10
PAGE 13
6WMMC7 Series FLOPPY : Floppy Port AC97 CPU AU 8810 GMCH/ 6WMMC7 FWH32 82810/ 810E ICH/ 82801 1 ATX POWER : ATX Power Connector AC97 1 11 ICH/ FWH32 82801 Pin No. Function CPU 3,5,7,13, GND 15-17 AU 8810 1,2,11 3.
PAGE 14
Quick Installation Guide COM A / LPT Port AC97PORT LPT COM CPU A AU 8810 6WMMC7 GMCH/ 82810/ 810E ICH/ FWH32 82801 VGA : VGA Port AC97 CPU AU 8810 6WMMC7 FWH32 GMCH/ 82810/ 810E ICH/ 82801 12
PAGE 15
6WMMC7 Series JP12:Clear CMOS Function AC97 CPU 3 2 1 AU 8810 ICH/ FWH32 82801 PIN No. Function GMCH/ 1-26WMMC7 close Clear82810 CMOS 2-3 close Normal (Default) JP2: PS/2 Keyboard Power On Selection AC97 3 2 1 CPU PIN No.
PAGE 16
Quick Installation Guide J8:Game & Audio Port AC97 CPU AU 8810 Line Out GAME GMCH/ MIC 6WMMC7 Line In FWH32 82810/ 810E ICH/ 82801 J7:CD Audio Line In AC97 CPU 1 AU 8810 FWH32 ICH/ 82801 PIN No.
PAGE 17
6WMMC7 Series JP11:AUX_IN AC97 JP11 AU 8810 1 PIN No. 1 2,3 4 Function AUX_L CPU GND AUX_R GMCH/ 82810/ 810E 6WMMC7 ICH/ FWH32 82801 JP3 TEL :The connector is for Modem with internal voice connector. AC97 CPU 1 AU 8810 TEL PIN No.
PAGE 18
Quick Installation Guide JP18 SPDIF:(Optional for the SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dobly Digital decoder.) AC97 1 AU 8810 CPU PIN No. Function 1 VCC 2 SPDIF OUT GMCH/ 3 GND 82810/ 6WMMC7 810E ICH/ FWH32 82801 J14 : Wake on LAN AC97 1 2 3 PIN No.
PAGE 19
6WMMC7 Series J17 RING PWR ON: Internal Modem Card Ring Pwr On AC97 CPU AU 8810 ICH/ FWH32 1 PIN No. Function GMCH/ 1 Signal82810/ 6WMMC7 2 GND 810E 82801 JP1 : STR Function (If you want to use STR Function, please set jumper JP1 Closed.) AC97 CPU AU 8810 GMCH/ 82810/ 810E 1 6WMMC7 ICH/ FWH32 82801 PIN No.
PAGE 20
Quick Installation Guide JP10 : STR LED Connector & DIMM LED AC97 CPU STR LEDAUConnector 8810 External. 1 FWH32 ICH/ 82801 + JP10 6WMMC7 GMCH/ 82810/ 810E DIMM LED JP14 : Case Open AC97 JP14 1 PIN No.
PAGE 21
6WMMC7 Series JP16: Top Block Lock AC97 PIN No. Function Open TopAU Block Lock 8810 Close Top Block Unlock (Default) GMCH/ CPU 82810/ 6WMMC7 810E ICH/ FWH32 82801 JP13 :Safe mode/Recovery/Normal AC97 CPU AU 8810 1 FWH32 ICH/ 82801 6WMMC7 PIN No.
PAGE 22
Quick Installation Guide JP17: Onboard Sound Function (Optional) AC97 CPU AU 8810 1 FWH32 PIN No. 1-2close Function GMCH/ 82810/ Enabled Sound 6WMMC7 (Default) 810E ICH/ 82801 2-3close Disabled Sound TV/DFP :TV-Out / Digital Flat Panel Daughter Card Connector(Optional).
PAGE 23
6WMMC7 Series J13/J20 : USB Port Selection (Optional) AC97 CPU J13 J20 1 FWH32 1 ICH/ 82801 AU 8810 PIN No. J13 1-2close J206WMMC7 1-2close J13 2-3close J20 2-3close Function Front Panel USB GMCH/ 82810 Enable Back Panel USB Enable J19 : Front Panel USB Port (Optional) AC97 CPU 9 10 AU 8810 1 2 6WMMC7 FWH32 ICH/ 82801 PIN No.
PAGE 24
Quick Installation Guide JP15: Timeout Reboot Function AC97 CPU AU PIN8810 No.
PAGE 25
6WMMC7 Series AC97 AU 8810 PIN No. Function 1-2 close DisableCPU USB Device Wake-up (Default) 2-3 close Enable USB Device Wake-up JP19 6WMMC7 GMCH/ 82810 1 ICH/ want82801 to use (If you “USB KB/Mouse Wake from S3” function, you have to set the BIOS setting “USB KB/Mouse Wake from S3” enabled, and the jumper “JP19” enabled). *(Power on the computer and as soon as memory counting starts, press ~~. You will enter BIOS Setup.~~
PAGE 26
Quick Installation Guide JP20/JP21:Quad Speaker (Optional) AC97 CPU AU 8810 JP20 3 JP21 3 6WMMC7 FWH32 ICH/ 82801 JP20 JP21 JP20 JP21 2 1 2 1 GMCH/ 82810 PIN No. Function 1-2close LINE_IN 1-2close 2-3close QUAD OUT 2-3close JP24: FWH Write Protection AC97 CPU JP24 AU 8810 GMCH/ Open 6WMMC7 FWH32 Close 82810/ 810E ICH/ PIN No.
PAGE 27
6WMMC7 Series AC97 AU 8810 Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the CPU manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
PAGE 28
Quick Installation Guide III. Top Performance Test Setting: The following performance data list is the testing results of some popular benchmark testing programs. Users have to modify the value for each item in chipset features as follow for top performance setting.
PAGE 29
6WMMC7 Series These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.) • CPU Intel CeleronTM 466MHz Socket 370 processor • DRAM • CACHE SIZE (128x 1) MB SDRAM (SEC KM48S8030CT-GA) • DISPLAY Onboard Intel Corporation 810 Graphics Controller Hub) • STORAGE Onboard IDE (IBM DTNA-371800) • O.S. Windows NT™ 4.
PAGE 30
PAGE 31
6WMMC7 Series • CPU Celeron 433 OC 450 (100*4.5) • DRAM • STORAGE (64x 2) MB SDRAM (MITSUBISHI M2V64S40BTP) Onboard IDE (IBM DJNA-352030) (ATA66) Windows98 SE2 English Ver(FAT32), DirectX 6.1, Driver 4.11.01 1185 PV 1.1 1024*768*16 bit (75Hz) Motherboard ICH GMCH 6WMMC7 6WMMC7-1 82801AA 82810DC100 82801AA 82810 878 2410 4010 14100 141 392 878 2400 4010 14100 145 394 386 292 137.09 4.17 134.52 3.
PAGE 32
Suspend to RAM Installation IV. Suspend to RAM Installation A.1 Introduce STR function: Suspend-to-RAM (STR) is a Windows 98 ACPI sleep mode function. When recovering from STR (S3) sleep mode, the system is able, in just a few seconds, to retrieve the last “state” of the system before it went to sleep and recover to that state. The “state” is stored in memory (RAM) before the system goes to sleep.
PAGE 33
6WMMC7 Series Step 2: (If you want to use STR function, please set jumper JP1 Closed.) AC97 CPU AU 8810 1 PIN 6WMMC7 ICH/ FWH32 82801 GMCH/ 82810/ No. 810EFunction Close STR Enable Open STR Disable Step 3: Power on the computer and as soon as memory counting starts, press . You will enter BIOS Setup. Select the item “POWER MANAGEMENT SETUP”, then select “ACPI Suspend Type: S3 (Suspend to RAM)”. Remember to save the settings by pressing "ESC" and choose the “SAVE & EXIT SETUP” option.
PAGE 34
Suspend to RAM Installation A.3 How to put your system into STR mode? 1. There are two ways to accomplish this: Choose the “Stand by” item in the “Shut Down Windows” area. A. Press the “Start” button and then select “Shut Down” B.
PAGE 35
6WMMC7 Series 2. Define the system ”power on” button to initiate STR sleep mode: A. Double click “My Computer” and then “Control Panel” B. Double click the “ Power Management” item.
PAGE 36
Suspend to RAM Installation C. Select the “Advanced” tab and “Standby” mode in Power Buttons. Step 4: Restart your computer to complete setup. Now when you want to enter STR sleep mode, just momentarily press the “Power on” button.. A.4 How to recover from the STR sleep mode? There are seven ways to “wake up” the system: 1. 2. 3. 4. 5. 6. 7. Press the “Power On” button. Use the “Keyboard Power On” function. Use the “Mouse Power On” function. Use the “Resume by Alarm” function.
PAGE 37
6WMMC7 Series A.5 Notices : 1. In order for STR to function properly, several hardware and software requirements must be satisfied: A. Your ATX power supply must comply with the ATX 2.01 specification (provide more than 720 mA 5V Stand-By current). B. Your SDRAM must be PC-100 compliant. 2. Jumper JP10 is provided to connect to the STR LED in your system chassis. [Your chassis may not provide this feature.] The DIMM LED will be illuminated when your system is in STR sleep mode.
PAGE 38
PAGE 39
Table of Contents TABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE ..................................................................................................... 1-1 1.2. KEY FEATURES ........................................................................................... 1-1 1.3. PERFORMANCE LIST .................................................................................. 1-2 1.4. BLOCK DIAGRAM......................................................................................... 1-4 1.5.
PAGE 40
6WMMC7 Series 4. BIOS CONFIGURATION 4.1. ENTERING SETUP ....................................................................................... 4-1 4.2. CONTROL KEYS .......................................................................................... 4-1 4.3. GETTING HELP ............................................................................................ 4-2 4.3.1. Main Menu ......................................................................................... 4-2 4.3.2.
PAGE 41
Introduction 1. INTRODUCTION 1.1. PREFACE Welcome to use the 6WMMC7 Series(6WMMC7 / 6WMMC7-1) motherboard. It is a Socket 370 processor based PC / AT compatible system with PCI Bus, and has been designed to be the fastest PC / AT system. There are some new features allow you to operate the system with just the performance you want. This manual also explains how to install the motherboard for operation, and how to set up your CMOS Configuration with BIOS Setup program. 1.2.
PAGE 42
6WMMC7 Series 1.3. PERFORMANCE LIST The following performance data list is the testing results of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.
PAGE 43
Introduction • CPU Celeron 433 OC 450 (100*4.5) • DRAM • STORAGE (64x 2) MB SDRAM (MITSUBISHI M2V64S40BTP) Onboard IDE (IBM DJNA-352030) (ATA66) Windows98 SE2 English Ver(FAT32), DirectX 6.1, Driver 4.11.01 1185 PV 1.1 1024*768*16 bit (75Hz) Motherboard ICH GMCH 6WMMC7 6WMMC7-1 82801AA 82810DC100 82801AA 82810 878 2410 4010 14100 141 392 878 2400 4010 14100 145 394 386 292 137.09 4.17 134.52 3.
PAGE 44
6WMMC7 Series 1.4. BLOCK DIAGRAM Socket 370 CPU Host Bus 66/100/133MHz AGP Display 66/100/133 MHz 66/100/133 MHz GMCH 82810 82810DC100 82810E DFP 3.3V SDRAM 100 MHz Hub SDRAM SDRAM Display Cache ICS Interface 14.
PAGE 45
Introduction 1.5. INTRODUCE THE INTELCeleron TM Socket 370 Processor Figure 1: INTEL CeleronTM Socket370 Processor 1.6 INTRODUCE AMR The Audio Modem Riser (AMR) is a new port that supports both audio and modem. The main purpose of the AMR port is to provide lower cost and higher levels of integration at all levels of the PC platform. The backbone of the AMR interface is on AC’97 compliant AC-Link with support for codes.
PAGE 46
PAGE 47
6WMMC7 Series 2. SPECIFICATION 2.1. HARDWARE • CPU − Socket 370 processor. − 66/100/133 MHz Socket 370 on board. • PROTECTION − Speaker Alarm when detect "CPU FAN Failure" or “CPU Overheat”. − Automatically slow down CPU speed when "CPU Overheat". − H/W monitor power status (±5V, ±12V, VGTL,5VSB, CPU voltage & CMOS battery voltage). • SPEED − 66/100/133 MHz system speed. − 33 MHz PCI-Bus speed. • DRAM MEMORY − 2 banks 168 pins DIMM module sockets on board.
PAGE 48
Specification • Audio Ports • GREEN FUNCTION • BIOS • DIMENSION − − − − − − − − − − 1x Line in 1x Line out 1x Mic in 1x Game Port 1x CD Line in 1x TEL 1x SPDIF Out (Optional) 1x AUX In. Suspend mode support. Green switch & ACPI LED support. − IDE & Display power down support. − Monitors all IRQ / DMA / Display / I/O events. − Supports Plug & Play, DMI Function. − Micro ATX Form Factor, 4 layers PCB. 2.2. SOFTWARE • DRIVER − IUCD (Bus Master + Sound Driver + LDCM + Utility) − INTEL 82810 Driver.
PAGE 49
6WMMC7 Series 3. HARDWARE INSTALLATION 3.1. UNPACKING The main board package should contain the following: • The 6WMMC7 Series ( 6WMMC7/6WMMC7-1) main board. • USER'S MANUAL for main board. • Cable set for IDE, Floppy devices. • CD for main board Utility. [IUCD (Bus Master + Sound Driver + LDCM + Utility), INTEL 82810 Driver.
PAGE 50
Hardware Installation 3.2. MAIN BOARD LAYOUT 6WMMC7 Game & Audio JP14 VGA COMA USB PS/2 LPT AC97 JP2 WOL JP11 AMR JP17 J17 SYSTEM FAN J20 J13 J19 ATX PWR 810E DC100 ICH/ 82801 6WMMC7 BAT DIMM 1 DIMM 2 J9 J12 CPU GMCH 82810 JP13 JP12 JP24 JP3 JP20 JP21 SDRAM JP23 JP5 FWH32 CPU FAN SDRAM AU 8810 JP16 JP15 J7 TV/DFP JP22 IR JP19 JP18 JP10 POWER FAN IDE 2 IDE 1 JP1 Floppy ½Figure 3.
PAGE 51
6WMMC7 Series 3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS I/O Ports Connector USB IDE1 IDE2 PS/2 FLOPPY COMA LPT VGA ATX Power GAME & Audio USB port. For Primary IDE port. For Secondary IDE port. For PS/2 Mouse & Keyboard port. For Floppy port. For Serial port1 (COM A){Support Modem Ring On}. For LPT port. For VGA Port. For ATX Power Connector.
PAGE 52
Hardware Installation PWR FAN: Power FAN Connector Pin No. 1 2 3 Function GND. +12V SENSE SYS FAN: System FAN Connector Pin No. 1 2 3 Function GND. +12V SENSE J9:Buzzer Enable (Optional) Pin No. Open Close Function Internal Buzzer Disable Internal Buzzer Enable J17 RING PWR ON :Internal Modem Card Ring PWR On Pin No. 1 2 Function Signal GND JP2 : Keyboard Power On Selection Pin No. 1-2 close 2-3 close Function Enabled Keyboard Power On. Disabled Keyboard Power On(Default).
PAGE 53
6WMMC7 Series Pin No. 1 2,3 4 Function AUX_L GND AUX_R J14:Wake on LAN Pin No. 1 2 3 Function +5VSB GND Signal JP3:TEL –The connector for Modem with internal voice connector. Pin No. 1 2,3 4 Function Phone-in GND Mono-out JP1:STR Enable Pin No. Close Open Function STR Enable STR Disable (Default) JP14: Case Open Pin No. 1 2 Function Signal GND JP13 : Safe Mode/Recovery/Normal Pin No.
PAGE 54
Hardware Installation Pin No. Open Close Function Timeout Reboot. No Reboot on Timeout. (Default) JP17: Onboard Sound function (Optional) Pin No. 1-2 close 2-3 close Function Enabled Sound.(Default) Disabled Sound. J13/ J20: USB Port Selection (Optional) Pin No. 1-2 close 2-3 close Function Front Panel USB Port Enabled. Back Front Panel USB Port Enabled. J19: Front Panel USB Port (Optional) Pin No. 1,4,5,10 2 3,7,9 6 8 Function NC +5V GND USB P0+ USB P0- JP18: SPDIF (Optional) Pin No.
PAGE 55
6WMMC7 Series JP24:FWH Write Protection Pin No. Open Close Function Normal (Default) Write Protection.
PAGE 56
Hardware Installation HD: IDE Hard Disk Active LED 1 PIN 1: LED anode (+) PIN 2: LED cathode (−) GN: Green Function Switch Open : Normal operation Short : Entering Green Mode GD: Green LED 1 PIN 1 : LED anode (+) PIN 2 : LED cathode (− ) 3.4.
PAGE 57
6WMMC7 Series 3.5. CPU SPEED SETUP The system bus frequency can be switched at 66MHz / 100MHz / 133MHz and Auto by adjusting JP5,JP23. The CPU ratio is control by BIOS.
PAGE 58
Hardware Installation 3.6. CMOS RTC & ISA CFG CMOS RAM There're RTC & CMOS RAM on board; they have a power supply from external battery to keep the DATA inviolate & effective. The RTC is a REAL-TIME CLOCK device, which provides the DATE & TIME to system. The CMOS RAM is used for keeping the information of system configuration, so the system can automatically boot OS every time. Since the lifetime of internal battery is 5 years, the user can change a new Battery to replace old one after it cannot work.
PAGE 59
6WMMC7 Series 3.11. PERIPHERAL DEVICE INSTALLATION After the I/O device installation and jumpers setup, the main board can be mounted into the chassis and fixed by screw. To complete the main board installation, the peripheral device could be installed now. The basic system needs a display interface card. If the PCI - Bus device is to be installed in the system, any one of three PCI - Bus slots can be used. 3.12. KEYBOARD & PS/2 MOUSE INSTALLATION The main board supports PS/2 Mouse.
PAGE 60
BIOS Configuration 4.BIOS CONFIGURATION Award's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. 4.1. ENTERING SETUP Power On the computer and press ~~immediately will allow you to enter Setup.~~
PAGE 61
6WMMC7 Series 4.3. GETTING HELP 4.3.1. Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. 4.3.2. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press . 4.4. THE MAIN MENU Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 4.1) will appear on the screen.
PAGE 62
BIOS Configuration • Standard CMOS Features This setup page includes all the items in standard compatible BIOS. • Advanced BIOS Features This setup page includes all the items of Award special enhanced features. • Advanced Chipset Features This setup page includes all the items of chipset special features. • Integrated Peripherals This setup page includes all onboard peripherals. • Power Management Setup This setup page includes all the items of Green function features.
PAGE 63
6WMMC7 Series • Set User password Change, set, or disable password. It allows you to limit access to the system. • Save & Exit Setup Save CMOS value settings to CMOS and exit setup. • Exit Without Saving Abandon all CMOS value changes and exit setup.
PAGE 64
BIOS Configuration 4.5. STANDARD CMOS FEATURES MENU The items in Standard CMOS Setup Menu (Figure 4.2) are divided into 9 categories. Each category includes no, one or more than one setup items. Use the arrows to highlight the item and then use the or keys to select the value you want in each item.
PAGE 65
6WMMC7 Series • Date The date format is , . week month day year • The week, from Sun to Sat, determined by the BIOS and is display-only The month, Jan. Through Dec. The day, from 1 to 31 (or the maximum allowed in the month) The year, from 1994 through 2079 Time The times format in . The time is calculated base on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00.
PAGE 66
BIOS Configuration • Drive A type / Drive B type The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. None 360K, 5.25 in. 1.2M, 5.25 in. 720K, 3.5 in. 1.44M, 3.5 in. 2.88M, 3.5 in. • • No floppy drive installed 5.25 inch PC-type standard drive; 360K byte capacity. 5.25 inch AT-type high-density drive; 1.2M byte capacity (3.5 inch when 3 Mode is Enabled). 3.5 inch double-sided drive; 720K byte capacity 3.5 inch double-sided drive; 1.
PAGE 67
6WMMC7 Series • Halt on The category determines whether the computer will stop if an error is detected during power up.
PAGE 68
BIOS Configuration 4.6. Advanced BIOS Features CMOS Setup Utility-Copyright( C ) 1984-1999 Award Software Advanced BIOS Features Virus Warning Disabled Item Help CPU Cache Enabled CPU L2 Cache ECC Checking Disabled Menu Level Allows you to *Processor Number Feature Enabled choose the VIRUS Quick Power On Self Test Enabled Warning feature First Boot Device Floppy For IDE Hard disk Second Boot Device HDD-0 Boot sector Third Boot Device LS/ZIP Protection.
PAGE 69
6WMMC7 Series • CPU Cache These two categories speed up memory access. However, it depends on CPU / chipset design. The default value is Enabled. Enabled Disabled • Enable cache Disable cache CPU L2 Cache ECC Checking The default value is Disabled. Enabled Disabled • Enable CPU L2 Cache ECC Checking Disable CPU L2 Cache ECC Checking Processor Number Feature This item will show up when you install the Pentium III processor. The default value is Enabled.
PAGE 70
BIOS Configuration • First / Second / Third Boot device The default value is Floppy / HDD-0 / LS/ZIP.
PAGE 71
6WMMC7 Series • Boot Up NumLock Status The default value is On. • On Keypad is number keys. Off Keypad is arrow keys. Gate A20 Option The default value is Fast. Normal Fast • Set Gate A20 Option is Normal. Set Gate A20 Option is Fast. Typematic Rate Setting The default value is Disabled. Enabled Disabled • Enable Keyboard Typematic rate setting. Disable Keyboard Typematic rate setting. Typematic Rate (Chars / Sec.) The default value is 6. 6-30 • Set the maximum Typematic rate from 6 chars.
PAGE 72
BIOS Configuration • OS Select For DRAM>64MB The default value is Non-OS2. Non-OS2 OS2 • Using non-OS2 operating system. Using OS2 operating system and DRAM>64MB. HDD S.M.A.R.T. Capability The default value is Disable. • Enable Enable HDD S.M.A.R.T. Capability Disable Disable HDD S.M.A.R.T. Capability Report No FDD For WIN 95 The default value is No. No Yes Assign IRQ6 For FDD. FDD Detect IRQ6 Automatically.
PAGE 73
6WMMC7 Series 4.7.
PAGE 74
BIOS Configuration • SDRAM RAS- to-CAS delay The default value is 2 Set SDRAM RAS- to-CAS delay 3 SCLKs. Set SDRAM RAS-to-CAS delay 2 SCLKs. 3 2 • SDRAM RAS Precharge The default value is 2. 3 2 • Set SDRAM RAS Precharge is 3. Set SDRAM RAS Precharge is 2. SDRAM Buffer Strength The default value is Auto. Auto Auto-1 Auto+1 • Set SDRAM Buffer Strength Auto. Set SDRAM Buffer Strength Auto-1. Set SDRAM Buffer Strength Auto+1. DRAM Page Closing Policy The default value is Precharge Bank.
PAGE 75
6WMMC7 Series • Delayed Transaction The default value is Disabled. Disabled Enabled • Normal operation. For slow speed ISA device in system. On-Chip Video Window Size The default value is 64MB. • 32MB Set Graphics Aperture Size to 32MB. 64MB Set Graphics Aperture Size to 64MB. Local Memory Frequency The default value is 100MHz. 100MHz 133MHz • Set Local Memory Frequency to 100MHz. Set Local Memory Frequency to 133MHz. Initialize Display Cache The default value is Enabled.
PAGE 76
BIOS Configuration 4.8.
PAGE 77
6WMMC7 Series • On-Chip Primary PCI IDE The default value is Enabled. • Enabled Enable onboard 1st channel IDE port. Disabled Disable onboard 1st channel IDE port. On-Chip Secondary PCI IDE The default value is Enabled. • Enabled Enable onboard 2nd channel IDE port. Disabled Disable onboard 2nd channel IDE port. IDE Primary Master PIO (for onboard IDE 1st channel). The default value is Auto. Auto BIOS will automatically detect the IDE HDD Accessing mode.
PAGE 78
BIOS Configuration • IDE Secondary Slave PIO (for onboard IDE 2nd channel). The default value is Auto. • Auto BIOS will automatically detect the IDE HDD Accessing mode. Mode0~4 Manually set the IDE Accessing mode. IDE Primary Master UDMA. The default value is Auto. • Auto BIOS will automatically detect the IDE HDD Accessing mode. Disabled Disable UDMA function. IDE Primary Slave UDMA. The default value is Auto. • Auto BIOS will automatically detect the IDE HDD Accessing mode.
PAGE 79
6WMMC7 Series • USB Controller The default value is Enabled. Enabled Disabled • Enable USB Controller. Disable USB Controller. USB Keyboard Support The default value is Disabled. Enabled Disabled • Enable USB Keyboard Support. Disable USB Keyboard Support. Init Display First The default value is PCI Slot. • PCI Slot Set Init Display First to PCI Slot. Onboard Set Init Display First to onboard AGP. AC’97 Audio The default value is Auto. Enabled Enabled AC’97 Audio.
PAGE 80
BIOS Configuration • POWER ON Function (Optional) The default value is BUTTON ONLY. Password Enter from 1 to 5 characters to set the Keyboard Hot KEY Power On Password. Please set password with three different characters, and press the three different characters password at the same time. Mouse Left Double click twice on PS/2 left bottom. Mouse Right Double click twice on PS/2 right bottom. BUTTON ONLY If your keyboard have “POWER Key” button, you can press the key to power on your system.
PAGE 81
6WMMC7 Series • UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) The default value is Normal ASKIR • Onboard I/O chip supports ASKIR. IrDA Onboard I/O chip supports IrDA. Normal Onboard I/O chip supports Normal. RxD , TxD Active The default value is Hi,Lo. Hi, Hi Hi, Lo Lo, Hi Lo, Lo • RxD set Hi, TxD set Hi RxD set Hi, TxD set Lo RxD set Lo,TxD set Hi RxD set Lo,TxD set Lo IR Transmittiion delay The default value Enabled.
PAGE 82
BIOS Configuration • EPP Version The default value is 1.7. EPP 1.9 EPP 1.7 • EPP Version is 1.9. EPP Version is 1.7. ECP Mode Use DMA The default value is 3. 1 3 • Set ECP Mode Use DMA is 1. Set ECP Mode Use DMA is 3. Game Port Address The default value is 201. Disabled Disabled On Board IDE 201 Set onboard game port is 201. 209 Set onboard game port is 209. • Midi Port Address The default value is 330. Disabled Disabled On Board Midi Port. 300 Set On Board Midi Port is 300.
PAGE 83
6WMMC7 Series 4.9.
PAGE 84
BIOS Configuration • Power Management The default value is User Define. User Define Min Saving Max Saving • For configuring our own power management features. Enable Green function. Disable Green function. Video off Method The default value is DPMS. V/H SYNC+Blank Blank Screen DPMS • BIOS will turn off V/H-SYNC when gets into Green mode for Green monitor power saving. BIOS will only black monitor when gets into Green mode. BIOS will use DPMS Standard to control VGA card.
PAGE 85
6WMMC7 Series • Suspend Mode The default value is Disable. Disabled 1 min - 1 Hour • Disable Suspend Mode. Setup the timer to enter Suspend Mode. HDD Power Down The default value is Disable. Disable 1-15 mins. • Disable HDD Power Down mode function. Enable HDD Power Down mode between 1 to 15 mins. Soft-off by PWR-BTTN The default value is Instant-off. Instant-off Delay 4 Sec. • Soft switch ON/OFF for POWER ON/OFF Soft switch ON 4sec. for POWER OFF.
PAGE 86
BIOS Configuration • ModemRingOn / WakeOnLan The default value is Enabled. Disabled Enabled • Disable these functions. Enable these functions. FAN Off In Suspend The default value is Enabled. Disabled Enabled • Disable this function. Stop CPU FAN when entering Suspend mode. USB KB/Mouse Wake From S3 The default value is Disabled. Disabled Enabled • Disable USB K/B Mouse Wake From S3 Enable USB K/B Mouse Wake From S3. CPU Thermal-Throttling The default value is 50%. 87.5% 75.0% 62.5% 50.0% 37.
PAGE 87
6WMMC7 Series • Resume by Alarm The default value is Disabled. Disabled Enabled Disable this function. Enable alarm function to POWER ON system. If the default value is Enabled. Date ( of Month) Alarm : Time ( hh: mm: ss) Alarm : • 0~31 (0~23) : (0~59) : (0~59) Primary IDE 0/1 The default value is Disabled. Disabled Enabled • Disable this function. Enable monitor Primary IDE 0/1 for Green event. Secondary IDE 0/1 The default value is Disabled. Disabled Enabled • Disable this function.
PAGE 88
BIOS Configuration 4.10.
PAGE 89
6WMMC7 Series • Resources Controlled by The default value is Auto (ESCD) Manual Auto • User can set the PnP resource (I/O Address, IRQ & DMA channels) used by legacy ISA DEVICE. BIOS automatically use these PnP rescuers. IRQ (3,4,5,7,9, 10,11,12,14,15),DMA(0,1,3,5,6,7) assigned to The default value is "Legacy ISA" or "PCI/ISA PnP". • Legacy ISA The resource is used by Legacy ISA device. PCI/ISA PnP The resource is used by PCI/ISA PnP device (PCI or ISA).
PAGE 90
BIOS Configuration 4.11. PC Health Status CMOS Setup Utility-Copyright( C ) 1984-1999 Award Software PC Health Status Reset Case Open Status Disabled Item Help Case Opened Yes Current CPU Temperature Menu Level 0°C/32°F CPU FAN Fail Alarm 5487 RPM Power FAN Fail Alarm 0 RPM System FAN Fail Alarm 0 RPM VCORE 2.01 V VGTL 1.48 V VCC3 3.45 V + 5V 5.02 V +12V 12.16 V - 12V -11.70 V - 5V - 5.09 V VBAT 3.00 V 5VSB 5.
PAGE 91
6WMMC7 Series • Current Voltage (V) VCORE / VGTL/ VCC3 / ±12V / ±5V /VBAT /5VSB Detect system’s voltage status automatically. • CPU Warning Temperature (°C / °F) The default value is 70°C /158°F 65°C / 149°F 70°C / 158°F 75°C / 167°F Disabled • Monitor CPU Temp. at 65°C / 149°F Monitor CPU Temp. at 70°C / 158°F Monitor CPU Temp. at 75°C / 167°F Disabled this function. Shutdown Temp. (°C / °F) (This function will be effective only for the operating systems that support ACPI Function.
PAGE 92
BIOS Configuration 4.12. Frequency/Voltage Control CMOS Setup Utility-Copyright( C ) 1984-1999 Award Software Frequency/Voltage Control Auto Detect DIMM/PCI Clk Enabled Item Help Spread Spectrum Disabled CPU Type CELERON ™ 200 Menu Level ↑↓→ ←Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 4.9: Frequency/Voltage Control • Auto Detect DIMM/PCI Clk The default value is Enabled.
PAGE 93
6WMMC7 Series • CPU Type CELERON (Depends on Your CPU Type) 1. System Bus Speed :66MHz 200 / 233 / 266 / 300 / 333 / 366 / 400 / 433 / 466 / 500 / 533 2. System Bus Speed : 100MHz 300 / 350 / 400 / 450 / 500 / 550 / 600 / 650 / 700 / 750 / 800 3.
PAGE 94
BIOS Configuration 4.13.
PAGE 95
6WMMC7 Series 4.14.
PAGE 96
BIOS Configuration 4.15. Set Supervisor / User Password When you select this function, the following message will appear at the center of the screen to assist you in creating a password.
PAGE 97
6WMMC7 Series 4.16.
PAGE 98
BIOS Configuration 4.17.
PAGE 99
PAGE 100
6WMMC7 Series APPENDIX A: Onboard Driver Installation Procedure (In this manual, we assume that your CD-ROM Drive letter to be Drive D: ) Please reference TUCD CD directory D: \ Manual \ Whitney810.pdf 810 INF update utility can’t find ICHxIDE.cat file automatically 1. After the installation is of Winodws98 is completed, run the “Setup.exe” of INF update utility. 2. System restarts. 3. System starts to recognize every new component. 4.
PAGE 101
PAGE 102
Appendix Appendix B : BIOS Flash Procedure BIOS update procedure: 9 Please check your BIOS vendor (AMI or AWARD) on the motherboard. 9 It is recommended you copy the AWDFlash.exe or AMIFlash.exe in driver CD (D:\>Utility\BIOSFlash) and the BIOS binary files into the directory you made in your hard disk. 【i.e:C:\>Utility\ (C:\>Utility : denotes the driver and the directory where you put the flash utilities and BIOS file in.
PAGE 103
PAGE 104
6WMMC7 Series Appendix C : AU8810 Driver Installation A. DRIVER INSTALLATION If you have older drivers in your system, please uninstall them first as described in Section C below. 1. Power on the system, placing the "Intel chipset Series Mainboard Utility CD" in the CD-ROM drive. 2. During the load process, Windows 95/98 should detect the Vortex PCI board and display a message such as "New Hardware Found".
PAGE 105
Appendix B. UNINSTALLING WINDOWS 95/98 DRIVERS To uninstall the Vortex software, you can use the following procedure: 1. Open to the Windows 95/98 Device Manager (right-click on "My Computer" and select "Properties"). 2. Open the "Multifunction Adapters" tree and select "Vortex Multifunction PCI Platform" 3. Press the "Remove" button at the bottom of the Device Manager window pane. 4. The drivers are now removed from memory, but are still on the hard disk. To delete the files from the hard disk: a.
PAGE 106
FCC Compliance Statement: DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) This equipment has been tested and found to comply with limits for a Class B digital device , pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.
PAGE 107
Declaration of Conformity We, Manufacturer/Importer (full address) G.B.T.
PAGE 108