GS-R127-RH Series GS-R127V-RH GS-R127H-RH 1U Rack Mount Server Service Guide Intel® Pentium XeonTM Processor Serverboard Rev. 1.
GS-R127-RH Series Rack Mount Server Table of Content Safety, Care and Regulatory Information ................................................ 4 Server Warnings and Cautions ............................................................... 8 Introduction .............................................................................................. 9 Contents Packages ................................................................................ 9 GS-R127-RH Series Model List ................................
Table of Content Chapter 5 BIOS Setup .......................................................................... 29 Main ........................................................................................................... 31 Advanced Processor Options ........................................................................................ 33 Advanced ................................................................................................... 36 Memory Configuration ..........................
GS-R127-RH Series Rack Mount Server Safety, Care and Regulatory Information Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. * The product should be operated only from the type of power source indicated on the rating label. * If your computer has a voltage selector switch, make sure that the switch is in the proper position for your area.
Safety Information * To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord. * Do not plug a telephone cable into the network interface controller (NIC) receptacle. * Do not use a telephone line to report a gas leak while you are in the vicinity of the leak. Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
GS-R127-RH Series Rack Mount Server Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de Classe A prescrites dans le reglement sur le brouillage radioelectrique edicte par Industrie Canada.
Safety Information NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the Load Numbers of all the devices does not exceed 100. / for European users only / CAUTION Danger of explosion if battery is incorrectly replaced.
GS-R127-RH Series Rack Mount Server Server Warnings and Cautions z z z z z 8
Introduction Introduction Welcome to Gigabyte GS-R127-RH Rack mount Server System Installation Guide. The guide provides instructions for configuration hardware for the GS-R127-RH your system. This installation guide will assist you in installing all the essential components for the sever system. For your protection, please read and undertand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference.
GS-R127-RH Series Rack Mount Server Chapter 1 Features Summary Motherboard GA-7BPSH00-RH (GS-R127V-RH) GA-7BPSH01-RH (GS-R127H-RH) Processor Supported Dual Intel® XeonTM Dual Core in LGA 771 socket Supports 667/1066MHz FSB (Dempsey) Supports 1066/1333MHz FSB (Woodcrest) 2nd cache depend on CPU Chipset Intel® 5000P Chipset Intel® 6321 ESB System Memory: Memory Capacity Supports 4 Channel memory bus up to 32GB Memory Type Error Correction: 8 x Registered Fully Buffered DIMM (FBD) 533/667MHz Single-b
Feature Summary Integrated Graphics: Controller ATI ES1000 Mass Storage System 4 x Hot Swapable HDDs 1 Slim Type 24X CD-ROM Front Panel Power SW, Reset SW, NMI SW, UID SW, 2 x LAN LED 1 x Power/Sleep LED 1 x HDD LED 1 x System Status LED 2 x USB Super I/O Controller ITE IT8718 Additional Features Hardware Monitor Supports Wake on Ring CPU/System Fan Revolution detect CPU/System temperature detect (Controlled by Winbond W83792G) System Voltage Detect Built-in I/O 1 x Serial ports (COM, at rear) 1
GS-R127-RH Series Rack Mount Server Server Management Functions: BMC Chip Failure Detection IPMI 2.0 controller IPMI 2.0 specification of Server management Event Logging Remote Management 32KB Nonvolatile Memory to Log System Failure Events Follow the IPMI 2.
Hardware Installation Process Chapter 2 System Hardware Installation Please observe the safety information in chapter “Important Safety Information” Do not expose the server to extreme environmental conditions. Protect it from dust, humidity, and heat. Step 2-1: Chassis Removal and Installation Step 1 Loosen thscrew from the top cover. Step 2 Push down the indentation located at two sides of the chassis, and slide toward to remove the top cover. Step 3 Reverse Step 1, and 2 to replace the chassis cover.
GS-R127-RH Series Rack Mount Server Step 2-2: CPU Installation Please make sure the CPU type and speed that are supported by the motherboard. Step 1 Raise the metal locking lever on the socket. Step 2 Remove the plastic covering on the CPU socket and lift the metal cover. Step 3 Insert the CPU with the correct orientation. The CPU only fits in one orientation. Step 4 Once the CPU is properly placed, please replace the plastic covering and push the metal lever back into locked position.
Hardware Installation Process Step 2-3: Heat Sink Installation Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well remember to apply the thermal conductivity compound on the CPU. Step 2 Seat the heat sink with the four screws. Installation completed. Step 1 Step 2-4: Memory Installation 1. The DIMM slot has a notch, so the DIMM memory module can only fit in one direction. 2. Insert the DIMM memory module vertically into the DIMM slot. Then push it down. 3.
GS-R127-RH Series Rack Mount Server Step 2-5: PCI Expansion Card Installation GS-R127V-RH provides expansion riser slot for one PCI-X 64/100MHz slot; and one with PCI-E x8. To install the peripheral, please go through the following steps. Note: Before installing the PCI expansion card, please check the card size limitation. Size limitation for PCI-E is listed below: Heigth: 18.73mm(max) ; Length: 167.
Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button and pull the blank out of the drive bay. Step 2 Remove the hard disk blank. Slide hard disk into blank and secure it with screws. Step 3 Slide the drive into the cage until it clicks, locking the drive into place. Connect cable and power. Step 2 Step 1 Release button Step 2-7: Fan Duct Removal and Installation Step 1 Pull up the screw-holder and lossen the thumbscrews. Lift up to remove the fan duct.
GS-R127-RH Series Rack Mount Server Chapter 3 Appearance of GS-R127V-RH 3-1: Front View of GS-R127V-RH Slim Type CD-ROM USB Connector LE D s Hot swap SCSI HDDs 3-2: Front View of GS-R127H-RH Slim Type CD-ROM USB Connector LE D s Hot swap SAS HDDs 18
System Appearance 3-3: Rear View of GS-R127V-RH/GS-R127H-RH PS/2 Co nne cto rs USB Co nne cto rs LAN1 Po rt (RJ45) LAN2 Po rt (RJ45) COM Po rt VGA Po rt Limite d Lo w-Pro file PCI-E Rise r Slo t Full-He ig ht PCI-X Rise r Slo t Po we r co rd 19
GS-R127-RH Series Rack Mount Server 3-4: Switch and LED Indicators Introduction LAN1/2 Activities Reset Switch System Event LED HDD NMI Switch ID BTN&LED Power Name Color Condition Description Power Green Green On Blink Power On Sleep (S1) -Amber Off Blink Power Off (S4) System Ready but degraded, CPU Failed, Amber On DIMM Killed Critical Alarm: Critical Power Module Failure, SYS (System) Critical FANs Failure, Voltage (Power Supply) Critical Teemperature and Voltage HDD -Green Off Blin
LED Description 3-5: LAN LED Description Name Color LAN Green Link/Activity Green Condition Description ON BLINK LAN Link / no Access LAN Access 10 LAN - OFF OFF Idle 10Mbps connection Speed 100 LAN Green ON 100Mbps connection BLINK ON Port identification with 10 or 100Mbps connection 1Gbps connection BLINK Port identification with 1Gbps connection Speed Green GbE LAN Yellow Speed Yellow 21
GS-R127-RH Series Rack Mount Server 3-6 : Connector Icon Description Suggest Icon Description Keyboard VGA Mouse LA N Serial Port USB 22
Motherboard Layout Chapter 4 Motherboard Layout & Jumper Setting 4-1: GA-7BPSH-RH Motherboard Layout 10 7 8 9 5 20 6 17 18 13 4 3 21 11 19 16 22 2 12 23 15 14 23 1
GS-R127-RH Series Rack Mount Server Intel LAN chip 24
Jumper Setting 4-2: Jumper Setting BIOS_WP (BIOS Write Protect Function) BIOS_WP 1 1-2 close: Disable BIOS Write Protect Function (Default setting) 1 2-3 close: Enable BIOS Write Protection Function 25
GS-R127-RH Series Rack Mount Server BIOS_TBL (CMOS Lock Function) BIOS_TBL 1 1-2 close: Disable Top BlockFunction (Default setting) 1 2-3 close: Enable CMOS Top Block Lock 26
Jumper Setting LAN1_DIS/LAN2_DIS (Lan1/Lan2 Enable/Disable Function) LAN1_DIS LAN2_DIS 1 1-2 close: Enable onboard LAN1/LAN2 device (Default setting) 1 2-3 close: Disable onboard Lan//Lan2 device 27
GS-R127-RH Series Rack Mount Server JP19 (Clear CMOS Function) You may clear the CMOS data to restore its default values by this jumper. Default value doesn’t include the “Shunter” to prevent from improper use this jumper. To clear CMOS, temporarily short 2-3 pin.
BIOS Setup Chapter 5 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERINGSETUP Power ON the computer and press immediately will allow you to enter Setup.
GS-R127-RH Series Rack Mount Server GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press . z Main z Advanced This setup page includes all the items in standard compatible BIOS.
BIOS Setup Main Once you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press to accept or enter the sub-menu. Figure 1: Main System Time The time is calculated based on the 24-hour military time clock. Set the System Time (HH:MM:SS) System Date Set the System Date. Note that the “Day” automatically changed after you set the date.
GS-R127-RH Series Rack Mount Server IDE Primary Master, Slave / Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installed in the computer. There are two types: auto type, and manual type. Manual type is user-definable; Auto type which will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category.
BIOS Setup Advanced Processor Options Advanced Processor Options: Dempsey CPU Advanced Processor Options: Woodcrest CPU 33
GS-R127-RH Series Rack Mount Server Advanced Processor Option This category includes the information of CPU Speed, Processor ID and Per Processor Core L2 Cache. And setup menu for Hyperthreading, Intel Virtualizational Technology, Thermal Management 2, C1 Enhanced Mode, Execute Disable Bit. Setup menu options will be variable depends on the type of CPU. Processor Reset Yes Select ‘Yes’ BIOS will clear historical processor status and reset all processors on next boot.
BIOS Setup PECI Interface The Platform Environmental Control Interface (PECI Interface) is designed specifically to convey system management information from the processor. It is a proprietary single wire bus between the processor and the chipset or other health monitoring device. Data from the Digital Thermal Sensors are processed and stored in a processor register (MSR) which is queried through the Platform Environment Control Interface (PECI).
GS-R127-RH Series Rack Mount Server Advanced About This Section: Advanced With this section, allowing user to configure your system for basic operation. User can change the processor options, chipset configuration, PCI configuration and chipset control.
BIOS Setup Memory Configuration Figure 2-1: Memory Configuration System Memory/Extended Memory/DIMM Group 1~8 Status These category is display-only which is determined by POST (Power On Self Test) of the BIOS. Memory Reset Yes Select ‘Yes’, system will clear the memory error status. Save the changes and restart system. After rebooting system, the Memory Reset item will set to ‘No’ automatically. No Disable this function.
GS-R127-RH Series Rack Mount Server Extend RAM Step Enabled Enable test extended memroy process. Disabled Disable this function. (Default setting) Memory Branch Mode Sequential Memory will use sequential mode to save date. Interleave Memory will use Interleave mode for to distribute every one memory to save date. (Default setting) Mirror Mirror will use backup date by image. Only half of the total memory is report to OS. Single Channel 0 Disable Default operate Dual channel Mode.
BIOS Setup PCI Configuration Figure 2-2: PCI Configuration Embedded NIC LAN 1 Option ROM Scan Enabled Enable onboard LAN1 device and initialize device expansion ROM. (Default setting) Disabled Disable this function. LAN2 Option ROM Scan Enabled Enable onboard LAN2 device and initialize device expansion ROM. (Default setting) Disabled Disable this function.
GS-R127-RH Series Rack Mount Server PCI Slot 1/2 Option ROM Enabled Enableing this item to initialize device expansion ROM. (Defualt setting) Disabled Disable this function. Adaptec 7901 Option ROM Enabled Enableing this item to initialize device expansion ROM. (Default setting) Disabled Disable this function. SAS Option ROM Enabled Enableing this item to initialize device expansion ROM. (Default setting) Disabled Disable this function.
BIOS Setup I/O Device Configuration Figure 2-3: I/O Device Configuration Serial Port A This allows users to configure serial prot A by using this option. Enabled Enable the configuration (Default setting) Disabled Disable the configuration. Base I/O Address/IRQ 3F8/IRQ4 Set IO address to 3F8. (Default setting) 2F8/IRQ3 Set IO address to 2F8. 3E8/IRQ4 Set IO address to 3E8. 2E8/IRQ3 Set IO address to 2E8.
GS-R127-RH Series Rack Mount Server PS/2 Mouse Set this option ‘Enabled’ to allow BIOS support for a PS/2 - type mouse. Enabled ‘Enabled’ forces the PS/2 mouse port to be enabled regardless if a mouse is present. (Default setting) Disabled ‘Disabled’ prevents any installed PS/2 mouse from functioning, but frees up IRQ12. USB Controller This item allows users to enable or disable the USB device by setting item to the desired value. Enabled Enable USB controller.
BIOS Setup Parallel ATA Enabled Enable Parallel ATA. (Default setting) Disabled Disable the device. Serial ATA Enabled Enables on-board serial ATA function. (Default setting) Disabled Disables on-board serial ATA function. ` Native Mode Operation This option allows user to set the native mode for Serial ATA function. Auto Auto detected. (Default setting) Serial ATA Set Native mode to Serial ATA.
GS-R127-RH Series Rack Mount Server Advanced Chipset Control Figure 2-4: Advanced Chipset Control Enable Multimedia Timer Yes Enable Multimedia Timer support. No Disable this function. (Default setting) Crystal Beach Configure Enable Enable Configuration/Memory mapped accesses to the Crystal Beach Configuration sapce located in Device 8, Fn0, and Fn1. Enabled Crystal Beach Configure function. (Default setting) Disabled Disable this function.
BIOS Setup I/O Acceleration Technology It addresses all segments of the server I/O bottleneck problem using TCP/IP and without requiring any modification of existing or future applications. Enabled Enable I/O Acceleration Technology. (Default setting) Disabled Disable this function. Wake On Ring This option allow user to determine the action of the system power is off and the modem is ringing. Enabled Enable Wake On Ring. (Default setting) Disabled Disable this function.
GS-R127-RH Series Rack Mount Server Hardware Monitor Figure 2-5: Hardware Monitor CPU1/2 Core1/2 Temperature/ Motherboard Temperature Display the current CPU1/CPU2 Core1/2 temperature, and Motherboard temperature. Voltage Monitor: +3.3V, +5V, VCOREA, VCOREB, VBAT Detect system's voltage status automatically. FAN Monitor: System 1/3/4/5/6/7/8/9/10 (RPM) Display the current System FAN 1/3/4/5/6/7/8/9/10 speed. This Menu will disappear when BMC module is populated.
BIOS Setup Boot -time Diagnostic When this item is enabled, system will shows Diagnostic status when system boot. Enabled Enable Boot-time Diagnostic. Disabled Disable this function. (Default setting) Reset Configuration Data Yes Reset all configuration data. No Do not make any changes. (Default setting) NumLock This option allows user to select power-on state for NumLock. On Enable NumLock. (Default setting) Off Disable this function.
GS-R127-RH Series Rack Mount Server Multiprocessor Specification This option allows user to configure the multiprocessor(MP) specification revision level. Some operating system will require 1.1 for compatibility reasons. 1.4 Support MPS Version 1.4 . (Default setting) 1.1 Support M PS Version 1.1. Case Open Status This item shows the Case Open Status. If system chassis is not closed properly, this item will show status as “ON”.
BIOS Setup Security Figure 3: Security Set Supervisor Password You can install and change this options for the setup menus. Type the password up to 6 characters in lengh and press . The password typed now will clear any previously entered password from the CMOS memory. You will be asked to confirm the entered password. Type the password again and press . You may also press to abort the selection and not enter a specified password or press key to disable this option.
GS-R127-RH Series Rack Mount Server Set User Password You can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password up to 6 characters in lengh and press . The password typed now will clear any previously entered password from the CMOS memory. You will be asked to confirm the entered password.
BIOS Setup Server Figure 4: Server 51
GS-R127-RH Series Rack Mount Server Server Management Figure 4-1: Server Managerment Server Management This category allows user to view the server management features. Including information of BIOS Version and GBIA Module Version. All items in this menu cannot be modified in user’s mode. If any items require changes, please consult your system supervisor.
BIOS Setup Console Redirection Figure 4-2: Console Redirection COM Port Address If this option is set to enabled, it will use a port on the motherboard. On-board COMA Use COMA as he COM port address. Disabled Disable this function. (Default setting) Baud Rate This option allows user to set the specified baud rate. Options 300, 1200, 2400, 9600, 19.2K, 38.4K, 57.6K, 115.2K. Console Type This option allows user to select the specified terminal type. This is defined by IEEE.
GS-R127-RH Series Rack Mount Server Flow Control This option provide user to enable the flow control function. None Not supported. XON/OFF Software control. CTS/RTS Hardware control. (Default setting) Continue C.R. after POST This option allows user to enable console redirection after O.S has loaded. On Enable console redirection after O.S has loaded. Off Disable this function.
BIOS Setup Post Error Pause If this item is set to enabled, the system will wai for user intervention on critical POST errors. If this item is disabled, the system will boot with no intervention if possible. Enabled Enable Post Error Pause. (Default setting) Disabled Disable this function. After Power Failure This option provides user to set the mode of operation if an AC / power loss occurs. Power On System power state when AC cord is re-plugged.
GS-R127-RH Series Rack Mount Server Mini BMC Function Enabled Enable Mini BMC function. (Default value) Disabled Disable this function. This option will disappear and disable when BMC module is populated. Mini BMC SEL View Press [Enter] to view the Mini BMC SEL. This option will disappear and disable when BMC module is populated.
BIOS Setup Boot * About This Section: Boot The “Boot” menu allows user to select among four possible types of boot devices listed using the up and down arrow keys. By applying <+> and key, you can promote devices and by using the <-> key, you can demote devices. Promotion or demotion of devices alerts the priority that the system uses to search for boot device on system power on.
GS-R127-RH Series Rack Mount Server Boot Priority Order This field determines which type of device the system attempt to boot from after PhoenixBIOS Post completed. Specifies the boot sequence from the available devices. If the first device is not a bootable device, the system will seek for next available device. Key used to view ot configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down. and specifies the device fixed or removable.
BIOS Setup Exit Figure 6: Exit * About This Section: Exit Once you have changed all of the set values in the BIOS setup, you should save your chnages and exit BIOS setup program. Select “Exit” from the menu bar, to display the following sub-menu.
GS-R127-RH Series Rack Mount Server Exit Saving Changes This option allows user to exit system setup with saving the changes. Press on this item to ask for the following confirmation message: Pressing ‘Y’ to store all the present setting values tha user made in this time into CMOS. Therefore, whenyou boot up your computer next time, the BIOS will re-configure your system according data in CMOS.
BIOS Setup Exit Discarding Changes This option allows user to exit system setup without changing any previous settings values in CMOS. The previous selection remain in effect. This will exit the Setup Utility and restart your compuetr when selecting this option. Load Settup Default This option allows user to load default values for all setup items.
GS-R127-RH Series Rack Mount Server Discard Changes This option allows user to load previos values from CMOS for all setup item.
BIOS Setup Save Changes This option allows user to save setup dat ato CMOS. When you press on this item, you will get a confirmation dialog box with a message as below: Press [Yes] to save setup daya to CMOS.
GS-R127-RH Series Rack Mount Server Revision History Chapter 6 Driver Installation A. Intel Chipset Software Installation Utility Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. Installation Procedures: 1.
Driver Installation 2. Setup Wizard 2. Click "Next". 3. License Aggremment 3. Click "Yes".
GS-R127-RH Series Rack Mount Server 4. Readme Information 4. Click "Next". 5. Installation Completed 5. Installation completed, Click "Finish" to restart computer.
Driver Installation B. ATI ES1000 VGA Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. Installation Procedures: 1. The CD auto run program starts, Double click on “ATI VGA Driver” to start the installation. 2. Then, a series of installation wizards appear.
GS-R127-RH Series Rack Mount Server 2. Setup Wizard 2. Click "Next". 3. License Aggremment 3. Click "Yes".
Driver Installation 4. Installation Complete 4. Click "Finish".
GS-R127-RH Series Rack Mount Server C. Intel LAN Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. Installation Procedures: 1. The CD auto run program starts, Double click on “Intel LAN Driver” to start the installation. 2. Select “Install Driver. 3.
Driver Installation 2. Installation Wizard Welcom Window 2. Click "Install Driver" Item. 3. InstallShield Wizard Welcome Window 3. Click "Next".
GS-R127-RH Series Rack Mount Server 4. License Agreement 4. Select ‘I accept the term in the license agreement’ and click ‘Next’ 5. Select Setup Type 5. Click "Next". Step 5. User can select either Complete or Custom Setup Types. Complete setup type allows users to Installs drivers, Intel PROSet for Windows* Device Manager, and Advanced Networking Services. Custom setup type embraces installing features and subfeatures user selects, including modern utilities, manage ment components and drivers.
Driver Installation 6. Ready to instll program 6. Click "Install" to start installation. 7. Installation Complete 7. Wizard Completed. Click "Finish".
GS-R127-RH Series Rack Mount Server D. AIC-7901 RAID Driver Installation (GS-R127V-RH) Installation Procedures: 1. The CD auto run program starts, Double click on “AIC-7901 RAID Driver” to make a driver disk. 2. Select a folder refering to your operating system. 3. Insert a flopp disk in the floppy drive. Copy file and paste to the floppy disk. 4. Driver disk creation completed. 1. Autorun 1. Click "AIC-7901RAID Driver” item.
Driver Installation 2. Select RIAD Driver Folder 3. Start to make a driver disk Insert a floppy disk, copy file to and the floppy paste to the disk. floppy disk.
GS-R127-RH Series Rack Mount Server E. LSI-1068 RAID Driver Installation (GS-R127H-RH) Installation Procedures: 1. The CD auto run program starts, Double click on “LSI-1068 RAID Driver” to make a driver disk. 2. Select a folder refering to your operating system. 3. Insert a flopp disk in the floppy drive. Copy file and paste to the floppy disk. 4. Driver disk creation completed. 1. Autorun 1. Click "LSI-1068 RAID Driver” item.
Driver Installation 2. Select RIAD Driver Folder 3. Start to make a driver disk Insert a floppy disk, copy file and paste to the floppy disk.
GS-R127-RH Series Rack Mount Server F. DirectX 9.0C Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. Installation Procedures: 1. The CD auto run program starts, Double click on “Directx9.0C” to start the installation. 2. Then, a series of installation wizards appear.
Driver Installation 2. License Agreement 2. Select “I accept the agreement and click "Next" to process the installation. 3. Start Installaiton 3. Click “Next” to start the installation .
GS-R127-RH Series Rack Mount Server 4. Installaiton Wizard completed 4. Click "Finish". Installation complete.
Appexdix Chapter 7 Appendix 7-1: Acronyms Acronyms ACPI Meaning Advanced Configuration and Power Interface APM AGP Advanced Power Management Accelerated Graphics Port AMR ACR Audio Modem Riser Advanced Communications Riser BBS BIOS BIOS Boot Specification Basic Input / Output System CPU CMOS Central Processing Unit Complementary Metal Oxide Semiconductor CRIMM CNR Continuity RIMM Communication and Networking Riser DMA DMI Direct Memory Access Desktop Management Interface DIMM DRM Dual Inline
GS-R127-RH Series Rack Mount Server Acronyms Meaning I/O IOAPIC Input / Output Input Output Advanced Programmable Input Controller ISA LAN Industry Standard Architecture Local Area Network LBA LED Logical Block Addressing Light Emitting Diode MHz MIDI Megahertz Musical Instrument Digital Interface MTH MPT Memory Translator Hub Memory Protocol Translator NIC OS Network Interface Card Operating System OEM PAC Original Equipment Manufacturer PCI A.G.P.
