GIGABYTE ODIN Power Supply User’s Manual ATX 12V version 2.2 power supply Products: ODIN GT / ODIN PRO Models: GE-S800A-D1, GE-S680A-D1, GE-S550A-D1 / GE-M800A-D1, GE-M680A-D1, GE-M550A-D1 Specifications are subject to change without notice.
English Introduction The GIGABYTE Odin series power supply delivers outstanding compatibilities and performance for power users and hardcore gamers. It also delivers a comprehensive set of tuning utilities for performance optimization. Additionally, the all Japan-made capacitor design within the Odin series enhances overall system durability and stability. The Odin series power supply complies with the newest ATX 12V version 2.2 specifications, and goes beyond.
English GIGABYTE will continue to develop RoHS compliant PC components and provide valuable resources to promote and advance RoHS directive goals and objectives. The following are not covered by the warranty: 1. Using the product incorrectly or in a manner other than the designed purpose. 2.Nonobservance of the proper operation provided. 3.Malfunction due to interference from other devices 4. Unapproved medication of the product. 5.Consequential damage to other objects due to the product’s fault. 6.
English System Requirement 1. Windows 2000\ XP\ Vista 2. CD-Rom 3. Recommended HDD Space: 30Mb 4. Recommended RAM: 512mb RAM 5.
English Contain Item 1. Power Supply Power Supply Unit .....................................................P.06 Power Supply Cables ................................................P.07 Power Supply Connectors ........................................P.08 2. Specification Input ...........................................................................P.10 Output ........................................................................P.11 Remote On/Off ......................................................
English 1. Power Supply 1-1.Power Supply Unit a b f d g c h e a. b. c. d. e. f. g. AC In AC power switch PCI-E 1 cable management Red PCI-E 2 cable management Blue 12V, 5V, 3.3V peripheral power cable management Thermal sensor cable management (For Odin GT only) Fan speed control power cable management (For Odin GT only) h.
English 1-2.Power Supply Cables a. 24-pin main power connector b. 8-pin +12V CPU power connector c. 4-pin +12V CPU power connector d. 6-pin PCI-E power connector (for 550W only one PCI-E connector) e. USB Data connector (For Odin GT only) f. Smart cable management PCI-E (Red and Blue) power cable g. Smart cable management Peripheral power cable h. Smart cable management - Peripheral power with FDD connector cable i. Smart cable management S-ATA power cable j.
English 1-3.Power Supply Connectors 1-3-1. 24-PIN Main Power Connector 18AWG (Wire) Orange Blue Black Green (22AWG) Black Black Black Red Red Red Black Signal Pin Pin Signal 18AWG (Wire) +3.3Vdc -12Vdc COM PS-ON 13 14 15 16 1 2 3 4 +3.3Vdc +3.3Vdc COM +5Vdc Orange Orange Black Red COM COM COM 17 18 19 20 21 22 23 24 5 6 7 8 9 10 11 12 COM +5Vdc COM POK +5VSB +12V1dc +12V1dc +3.3Vdc Black Red Black Gray (22 AWG) Purple Yellow Yellow Orange +5Vdc +5Vdc +5Vdc COM 1-3-2.
English 1-3-5. FDD connector cable Pin 1 2 3 4 Signal +5VDC COM COM +12V4DC 18AWG (Wire) Red Black Black Yellow 1-3-6. Peripheral power with S-ATA HDD connector cable Pin 1 2 3 4 5 Signal +3.3 VDC COM +5VDC COM +12V4DC 18AWG (Wire) Orange Black Red Black Yellow 1-3-7. Smart cable management - Peripheral power with SATA HDD connector cable Pin 1 2 3 4 5 6 Signal +12 VDC COM +5VDC COM +3.3VDC NC 18AWG (Wire) Yellow Black Red Black Orange NC 1-3-8.
English 1-3-9. Fan Speed Control connectors Pin 1 2 3 Signal Com +5VDC Signal 24 AWG (Wire) Black Red Yellow 1-3-10.Smart Cable Management - Fan Speed Control connectors Pin 1 2 3 Signal Com +5VDC Signal 24 AWG (Wire) Black Red Yellow 1-3-11. Smart cable management - Thermal sensor Smart cable management Thermal sensor Connector CAUTION Don’t place the Thermal sensor between CPU and Cooler; it will damage the thermal sensor and probably cause the CPU overheating, and could damage the CPU. 2.
English 2-1-3 CURRENT 115Vac - 8.0A max / 230Vax - 4.0A max 115Vac - 10.0A max / 230Vax - 5.0A max (800W only) 2-1-4 INRUSH CURRENT 55A max. when AC input 115Vac at 25°C cold start 110A max. when AC input 230Vac at 25°C cold start 2-1-5 POWER EFFICIENCY 80% (min) at full load (typical) and 115Vac and 230Vac input (For 20%, 50%, 100% load condition) 2-1-6 LEAKAGE CURRENT 3.5mA max. 2-1-7 POWER FACTOR PF> 0.9 2-2 OUTPUT Voltage Max Load *1 Min Load Peak Load Regula tion Ripple & Noise 11 +5V 28.
English 2-3 REMOTE ON/OFF TTL High/PS-OFF; TTL Low/PS-ON VIL = 0.8V max, IIL = -1.6mAmax@Vin=0.4V VIH = 2.0V min @ Iin=-200uA, VIH = 5.25Vmax@open ckt. 2-4 HOLD-UP TIME 16msec (min.) at 80% of full load at 230Vac input 2-5 POWER GOOD DELAY 100-500 msec 2-6 POWER FAIL DELAY >1msec. 2-7 TURN-ON DELAY TIME 2000 msec max. At nominal line full load 2-8 TRANSIENT OVERSHOOT Step load changes of up to 50% of full load, while other loads remains constant within the rating.
English t 1: TURN-ON DELAY TIME t 2: RISE TIME t 3: POWER GOOD DELAY t 4: POWER FAIL DELAY t 5: HOLD-UP TIME 2-10 PROTECTION When OCP, OVP, OTP, or short protection is triggered, the main output will be latched off. The main outputs can be reset by cycling the DC remote on/off or AC power +5Vsb output is automatically recovered when a fault condition is removed. 2-10-1.
English 0°C to +50°C 2-11-2 Storage Temp -20°C to +70°C 2-11-3 Operating Humidity 20% to 90%, non condensing 2-11-4 Storage Humidity 5% to 95%, non condensing 2-11-5 Operating Altitude 0-10,000 feet 2-11-6 Storage Altitude 0-50,000 feet 2-12 HI-POT (Input/Out isolation) 2-12-1 PRIMARY TO SECONDARY 3535 Vdc for 3 seconds 2-12-2 INSULATION RESISTANCE Primary to earth ground 500Vdc, 50M ohms Min.
English 3. Installation Instruction (For a new system, please go directly to Section 4) 1. Switch off the system. 2. Disconnect the power cord from your old power supply. 3. Follow the direction provided in your case’s user manual to open your computer case. 4. Disconnect all the power connectors from the power supply to the motherboard and the peripheral devices such as the case fans, hard drives, and floppy drives, etc. 5. Remove the existing power supply from your computer case 6.
English 10. To connect peripheral devices, please use Smart Cable Management power connectors. 11. With a Smart Cable Management -Fan speed control power connector, users may connect two 3-pin system fans. This allows Odin GT power supply to monitor and control the speed of the fans you’ve connected (Odin GT only). CAUTION: Do not connect to the CPU fan 12.
English 13. To enable the software control function, connect the USB connector from the power supply to Motherboard. If there is no USB connector on the motherboard, please use the USB converter to connect to the rear of the motherboard or an add-on card with a USB I/O port. (Odin GT series only) To connect the USB connector to the rear I/O USB port, please use the converter, which is included in the package, and connect the converter to the rear USB port by passing the rear slot. (Odin GT series only) 14.
English 4. Power Tuner Installation Instruction (ODIN GT series only) For the first time of the system’s boot-up, Windows will inform that a new hardware is found, and there is no driver needed for Odin GT. To enable the software control function, please install the power supply management software, “Power Turner”, in the system to monitor and adjust the hardware function. 1. Start up the system. 2. Insert the CD in the ODD drive, and the installation should start automatically.
English 6. Power Tuner main page The images below display the Power Tuner window; all function can be controlled by a click of the mouse.
English 7. P-Tuner Voltage page Fan speed and voltage setting window Fan curve mode selection Thermometer sensor selection Power Supply fan / System fan switch Fan curve Start Voltage Start Temperature Switch between °C & °F Confirm setting Cancel setting Performance mode: High Fan speed to cool down power supply and system more efficiently.
English Please don’t set the voltage over Intel spec. It may cause the system into protection mode. (Power Tuner only allows the power supply to adjust the voltage within Intel spec. It is safe to adjust the voltage setting.) 8. P-Tuner Alarm: Watt 9.
English 10. P-Tuner Alarm Current 11. P-Tuner Alarm Fan Speed 12.
English NOTE: 1. When the program crashes, simply close the program and re-start it. 2. When there is an error within the settings, it will cause a boot-up failure to the hardware, normally caused by overvoltage or under-voltage protection. Therefore, to protect the hardware, the system will not boot up. Please follow the steps below to recover the system. a. Remove the AC power cord. b.
