Manualshelf

Installation Guide

ManualsBrandsGilati ManualsAppliances20 in. 240 lbs. /24H Half Size Cubes Undercounter/Freestanding Ice Maker with Auto-Self-Cleaning, Stainless Steel
123456
Table Of Contents
2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should be followed to reduce the
riskof fire,electric shockandinjurytopersonsorproperty.Read all instructions before
operating the machine for the first time.
CAUTION: ICE CAN’T BE STORED IN THE ICE BIN DURING NIGHT TIME,IT’S NOT
FRIDGE,ICE WILL BE MELTED TO WATER AND GET OUT OF THE MACHINE.
1. If connect with water supply, CAUTION: must connect the potable water supply;
2. The machine is intended to be used in household and similar applications such as:
-staff kitchen areas in shops,offices and other working environments;
-farm houses
-by clients in hotels,motels and other residential type environments;
-Catering industry and similar non-retail industry.
3. The machine should be used in household and without obstacles surrounded, good
ventilation place.There is must be 19.7in at least between the four sides of the machine
with the wall.
4. When using electrical appliances,basic safety precautions should be followed to reduce
the risk of fire,electric shock and injury to persons or property.Read all instructions
before using any appliance.
5. Don’t operate this or any other appliance with a damaged cord.
6. Connect to properly polarized outlets only.No other appliance should be plugged into the
same outlet.Be sure that the plug is fully inserted into the socket.
7. Don’t place the machine and power cord near flammable material.Do not cover the
cord.Do not submerge it in water.
8. We do not recommend the use of an extension cord,as it may overheat and become a
risk of fire.
9. Unplug the ice maker before cleaning or making any repairs or servicing.
10.Exercise caution and supervision when appliance is used near children.
11.Don’t use your ice maker outdoors.Avoid direct sunlight and make sure that there is at
least 19.7in of space between the back and sides of your unit and the wall.
12.Don’t use any liquid other than water in the unit to make the ice.
11
Common malfunction analysis
1) NO ICE
Issues
Check items
Possible causes
The machine
doesn’t work
Power cord
The plug didn’t plug
into socket
The fuse of
PCB
The fuse is melted or
broken
Ice bin
The ice is full
Power supply
No power or lower
voltage
Water supply
No water or water
pressure is low
Inlet valve
Inlet valve is broken
Proximity
switch
Proximity switch is
broken
Compressor
didn’t work
or stop
working
suddenly
Power supply
Lower voltage
Air inlet
Air inlet is congested
Condenser
Too much dust
covered
Refrigerant
Refrigerant leaked
compressor
Connection wire is
broken off
No water in
the water
tank
Float
Float was jammed or
damage
No water
supply
Pipes get clogged or
water outage
Water
leakage
Water inlet
Water inlet is
loosened
Inlet or outlet
pipe
It’s broken
2)Lower making capacity
Issues
Check items
Possible causes
solutions
Take too
long to
make ice
Water pressure
Lower water pressure
Check the water source
Water temperature
Water temperature is high
Change to a water source
of lower temperature
Ambient
temperature
Ambient temperature is too
high or too low
Change to a place of lower
temperature
Refrigerant
Refrigerant leakage
Contact the after sales
Productions
of ice cubes
is low and
the cube ice
is too thin
Condenser
Too much dust covered
causes bad ventilation,,will
take too long to make ice
Clean the condenser
Water pump
Water pump broken
Replace a water pump
Ambient
temperature
Ambient temperature is
relative high
Change to a place of lower
temperature
Air inlet
Air inlet is congested
Ensure that the machine’s
surrounding space of at
least 15 cm is clear of any
objects