User's Manual
Table Of Contents
- Introduction
- Parts Lists
- Important Safety Information
- Preliminary Precautions
- Safety Symbols and Warning Words
- Prevent Explosions and Fires
- Prevent Electrical Shock and Sparks
- React Quickly to Fuel Spills, Fires or Vehicle Impact
- 1 Use station EMERGENCY TOTAL ELECTRICAL SHUT-OFF immediately. Turn off all system circuit breake...
- 2 Call emergency numbers for fires, vehicle impact or any significant spills.
- 3 Use safety tape, cones or barricades to block the work area. Do not go near fuel spill or all...
- 4 Take precautions to avoid igniting fuel. Do not allow starting of vehicles in the area and...
- 5 Provide emergency and first aid assistance.
- 6 Use approved and safe procedures to clean up all spills with a “fuel or gasoline absorbent” mat...
- Emergency and First Aid Information
- Warning Labels
- Working Alone
- Contacting Emergency Personnel
- Informing Emergency Personnel
- Other Useful Safety Information
- Classifying Hazardous Locations
- The Advantage Series Installation
- Preparing for Installation
- 1 Before proceeding read and follow all safety instructions and procedures.
- 2 Open main access doors. Refer to MDE-2531, Pump and Dispenser Start-Up/ Service Manual for acce...
- 3 Disconnect and remove existing hardware according to the following:
- 4 Remove door mounting pin and right options door.
- 5 If unit has Cash Acceptor, remove door alarm and all hardware from old door and save.
- 6 Dispose of door. Save pin for reassembly.
- Modifying Right Options Door On Wide Frame Units
- 1 Remove all hardware from new right options door according to the following steps and save all p...
- 2 Use center punch and hammer to mark placement of pump stop or call button hole on new right opt...
- 3 Away from fuel island, drill a 7/8 inch diameter hole in location illustrated above.
- 4 Remove any burrs around hole with deburring tool or rounded file.
- Re-installing Button
- 1 Hold contact base on back of door and align with hole drilled earlier.
- 2 Insert push button from front of door by aligning tabs with slots in base.
- 3 Turn push button 45˚ clockwise to lock button to base.
- 4 Tighten two screws on base to secure push button and base assembly to door.
- 5 Attach contact block to base with center screw if not already installed.
- 6 If unit does not have door alarm, reinstall all new right options door hardware except sheet me...
- Re-installing Door Alarm Switches
- 1 Remove lock hardware from new right options door.
- 2 Re-install C-clips removed from old right side option doors on new door.
- 3 Install door alarm assembly to door alarm assembly bracket with screw previously removed.
- 4 Attach door alarm assembly bracket to display board with screw previously removed.
- 5 Be sure magnet does not touch door alarm door bracket. Slightly move door alarm door bracket aw...
- 6 Reinstall all new right options door TRIND hardware except sheet metal cover by reversing proce...
- Installing Cables
- Position kit cables according to the following steps:
- 1 Carefully pry out printer cable retainer from underside of printer shelf.
- 2 Disconnect printer cable and pull cable out of 2 3/4" round hole from bottom, and install piece...
- 3 Feed three-prong end of power cable R20580-G1 and connector J250 end of R20437-G01 ribbon cable...
- 4 Reinstall printer cable and retainer disconnected and removed in step 2.
- Position kit cables according to the following steps:
- Installing Card Cage
- Prepare T20606-G3 card cage for installation.
- 1 Locate tab at left front top of card cage.
- 2 From B side of unit, turning card cage sideways to unit, feed top and rear of card cage up and ...
- 3 Position card cage so that tab fits over latch cutout for main door latch to secure card cage t...
- 4 Position rear of card cage on edge of cabinet shelf for easy cable connection.
- 5 Connect three prong female end of power cable R20580-G2 to card cage at location shown.
- 6 Locate harness attached to card cage containing P1 and P2 connectors.
- 7 Feed both harness cables down through hole as shown in illustration in Step 3 of “Installing Ca...
- Addressing The Advantage Series Units
- Install card cage assembly.
- Prepare T20606-G3 card cage for installation.
- Installing Right Option Door
- 1 If sheet metal shield has not been previously removed, using 1/4'' nut driver, remove sheet met...
- 2 Remove key taped to inside of new right options door and save.
- 3 Position new right options door and install with pin removed with old door and saved.
- 4 For narrow frame units, reconnect existing cables to new door PPU and main display.
- Route cables to Right Option Doors
- 1 Connect J182 on one R20773-G2 cable to A Side Light/Microreader PCB at P182, and do the same fo...
- 2 Route R20773-G2 cables around board as shown for both wide and narrow frame units, securing cab...
- 3 Route A side cable R20773-G2 along door with clamps provided with kit until connector end is fe...
- 4 Route A side card cage harness cable (with P1 connector) to door clamp, and connect to A Side R...
- 5 Route B side harness cable (with P2 connector) through clamps above CRIND tray to cable clamp i...
- 6 Reinstall sheet metal cover on door, being careful to avoid crimping cables.
- 7 Proceed to “Connecting Remaining Cables” on page31.
- Preparing for Installation
- MPD-3 Series Installation
- Removing Faceplate
- For units with slide-in faceplates on PMI bezels, do the following:
- For units with bolt-on faceplates on Mack bezels, do the following:
- 1 Open bezel door and lift until door is latched open.
- 2 Disconnect cable between manager keypad and logic board on bezel door. Discard cable.
- 3 Locate six sets of nuts and washers securing faceplate to bezel studs, and remove hardware.
- 4 Remove 6 sets of nuts and washers from faceplate studs and remove faceplate. Dispose of hardwar...
- 5 With putty knife, remove keypad door gasket and any adhesive residue.
- Providing Cable Access into Main Cabinet
- Installing Card Cage Assembly
- 1 Begin to separate card cage assembly into two pieces by removing one screw on top and two nuts ...
- 2 Disconnect cables joining two sides of card cage.
- 3 From ‘A’ side of unit, place bottom section of card cage fuse side first on to left shelf.
- 4 Reassemble card cage using nuts removed in Step 1 and two (2) tie wraps in place of screw and r...
- 5 For units with Screened Image Display (SIDs) only, do the following:
- 6 For all units, from ‘A’ side of unit, fasten card cage to shelf using 6-32 x 3/8" screw (Q12083...
- Installing TRIND™ Faceplate Assembly.
- For installing TRIND slide-in faceplates on PMI bezels, do the following:
- 1 Remove new TRIND faceplate assembly from box.
- 2 Peel adhesive backing off round gasket N23881-01. Install gasket adhesive side first to sheet m...
- 3 Feed ends of faceplate cables (with P1/2 connectors) through 3/4" hole on bezel door drilled in...
- 4 Follow these directions to install new TRIND faceplate:
- 5 Refer to MDE-2620, Graphics Panel Application for instructions on installing graphics.
- For installing TRIND™ bolt-on (stud type) faceplates, do the following:
- 1 Remove new TRIND faceplate assembly from box.
- 2 Remove existing manager keypad from bezel door, and use putty knife to remove keypad gasket and...
- 3 Replace the door gasket removed in step 2 with adhesive backed gasket Q11659- 01.
- 4 Replace existing keypad and keypad cable with T17549-G1 keypad assembly and R18163-G1 keypad ca...
- 5 Remove yellow tape on back of bezel door covering round hole.
- 6 Peel adhesive backing off round gasket N23881-01. Install gasket adhesive side first to seal ar...
- 7 Feed ends of faceplate cables with P1/2 connectors through 3/4" hole on door.
- 8 Install 6 split spacers K87404-01 on the faceplate side of the bezel door, in the mounting hole...
- 9 Install faceplate assembly T20616-G2, securing in place from back side of bezel door using in t...
- 10 Refer to MDE-2620, Graphics Panel Application for instructions on installing graphics.
- For installing TRIND slide-in faceplates on PMI bezels, do the following:
- Removing Faceplate
- Connecting Remaining Cables
- CRIND® BIOS TRIND™ Multi 1 Upgrade
- Dispenser Set-Up
- Addressing Dispenser
- Setting Baud Rate
- Addressing Gateway Board
- Testing TRIND™
- 1 For The Advantage series units, if printer was removed, replace printer and reconnect two cable...
- 2 Restore power to unit. Refer to Pump and Dispenser Service Manual MDE-2531.
- 3 Restoring power with new BIOS will Cold Start the CRIND. Refer to CRIND Service Manual MDE-2562.
- 4 Present test tag at option door from a distance of 6'' or less. Light board should light and fl...
- 5 When using test tag, screen will show “Test Confirmed”. In regular operation, screen will displ...
- Completing Installation
- 1 Close and secure option and maindoor.
- 2 Install graphics. Refer to MDE-2620 Graphics Installation for The Advantage Series.
- 3 Peel backing paper off FCC label pate provided in kit.
- 4 Affix FCC label plate to inside frame sheathing on column under existing FCC label.
- 5 Restore power to unit. Refer to Pump and Dispenser Service Manual MDE-2531.
- Cable Block Diagram
The Advantage Series Installation
Page 16 MDE-3883 TRIND Retrofit Kits C00011-005
• 10/00
PRELIMINARY
FCC 11/30
Modifying Right Options Door On Wide Frame Units
Note: T20613-G2 door assemblies are call/stop button ready, and do not need to be
modified. Instructions are provided for modifying T20613-G1 doors for call/
stop button.
For all narrow frame units, or wide frame units without stop or call buttons or
door alarm switches, proceed to “Installing Cables” on page 20. For wide or
narrow frame units without stop or call units but with door alarm, proceed to “Re-
installing Door Alarm Switches” on page 19. For wide frame units with stop or
call button previously installed on right options door, do the following to relocate
hardware to new T20613-G1 options door.
1 Remove all hardware from new right options door according to the following steps
and save all parts for reassembly.
• Remove two screws (1) mounting sheet metal antenna shield (2) on rear of
door. Save shield and screws for reassembly.
• Disconnect cable R20522-G1 (not shown) from light/multi-protocol reader
printed circuit board T20601-G1 (3) by disconnecting J181 on cable from P181
on board.
• Remove two standoff-screws (4) holding light/multi-protocol reader board (3),
and remove board. Save for reassembly.
• Remove four screws (5) and antenna board T20524-G1(6). Save for
reassembly.
1
2
3
4
5
6
Wide Frame Right Options Door
T20613-G1