GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 A System Overview .......................................................... 1 AB-100 Digital AudioBrick ................................................................... 1 AB-Clock ............................................................................................ 1 DR-50 ................................................................................................ 1 AB-50 .............
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 PA Zone Enables .............................................................................. 20 Half-Mute Zone Enables ................................................................... 20 Full-Mute Zone Enables .................................................................... 20 Input Triggering ...............................................................................
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Mute Track .................................................................................. 33 Mute All ....................................................................................... 33 Mute Cocked .............................................................................. 33 Mute Group ................................................................................
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Sound On 1/4 Hour ..................................................................... 43 Sound On 1/2 Hour ..................................................................... 43 Sound On 3/4 Hour ..................................................................... 43 Sound On Chime 1 ......................................................................... 43 Sound On Chime 2 ...................
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Balanced Audio Output ................................................................... 69 Digital Audio Repeater/Mixer to Adjustment Card ........................... 69 RS-485 Serial Data ........................................................................... 69 Power Supply ...................................................................................
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - MACs Eight Bit Digital Audio System - A System Overview The MACs Eight Bit Digital Audio System has been developed to meet all of your needs for Digital Audio Repeaters. The following repeaters are available: ¥ AB-100 Digital AudioBrick: Complete stand alone Digital Audio Repeater. It comes in a 5Ó x 12Ó x 2-1/2Ó aluminum box which can be mounted wherever you need to put it.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Ext. Inputs AB-100 Digital Audio Repeater Amp Because it is completely solid state, a Digital Audio Repeater never requires any maintenance. A sound which is recorded on a Digital Audio Repeater will sound just as good twenty or thirty years from now. Each AB-100, AB-Clock, AB-50 or DR-50 is a complete Digital Audio Repeater.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ¥ ¥ Volume, Bass and Treble controls on every card. You can use any number of cards in a system to provide any number of simultaneous audio tracks. To record a sound into a Digital Audio Repeater, a master (tape, CD, DAT, video tape) of the sound is played into a Macintosh or IBM compatible computer which has some sort of sixteen bit sound card installed.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 show the capacities with a variety of sounds using different sized Eproms: Approximate Play Times: Estimated Playing Times For Various Types Of Sounds Voices Number Of 27C512 Memory Chips Each Chip (1 chip) each Repeater (16 chips) each Expansion (32 chips) Low Rumbles 2 Khz 3 Khz 14 Sec. 9.3 Sec. 3.7 Min. 2.5 Min. 7.5 Min. 5 Min. 4 Khz 7.5 Sec. 2 Min. 4 Min. High Voices Music 5 Khz 7.5 Khz 5.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Actual Playing Times: The following tables show in seconds the capacities of several different types of Eproms at several different fixed bandwidths. All values shown are in seconds.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - 7.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Front Panel Adjustments, Inputs & Indicators: Several adjustments and indicators are available on the front panels of the AB-100, AB-Clock, DR-50 and AB-50. The front of an AB-100 or AB-Clock is shown below: AB-100 AudioBrick Gilderfluke & Co.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 c) Press and hold the button down while plugging the power supply back into the wall. d) After the repeater reboots, release the button. d) Reassemble the AB-100/AB-Clock. The defaults are now reloaded. You can reconfigure the AB-100/AB-Clock through the serial port at address 00h operating at 9600 baud, no parity.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - AB-100 and AB-Clock Connections The connections to the AB-100 and AB-Clock are identical. See the sections of this manual that cover the AB-50 and DR-50 for their connections. Unbalanced Output T+ S } gnd Amp Input 'B' Amp Aux. Port 1/4 J6 In 1 Common } gnd Input 'A' Balanced Output T+ R- S Status Output Line Level Out AB-100 AudioBrick Gilderfluke & Co.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Start Inputs and Status Outputs: Both the 'start' inputs and 'status' output for the AB-100 or AB-Clock are optically isolated from all other parts of the system. Connections are made through four screw terminals on the back of the AB-100 or AB-Clock. They can be configured to run either from the same power as the AB-100 or ABClock or from external power supply.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 adapter cable, so long as the wire isn't too long and there arenÕt too many AB-100s and AB-Clocks attached to the same serial line. To gain the full advantage of the RS-422/RS-485 signal levels (multidrop networking, distances of up to a mile) you will need to use a signal level adapter.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - AB-100 AudioBrick Configuration To configure the system through the serial port, you need to connect the system just as you do for any serial communications (see the 'AB-100 AudioBrick Serial Port Commands' section of the manual). The configuration mode is entered by the command: "m" (5AA5) (TRACK#) This command will bring up the following menu from the Repeater which was addressed.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 any card, you should use the ape key to redraw the screen while saving the print in the modem program running on your computer. This file can then be printed out at any time. Note that only one card in the entire system is allowed to be in configuration mode at one time.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 system. All cards in the system must be set to the same baud rate. The default speed is 9600 baud. This command doesn't take effect until you enter the eXit command. ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "c" Odd Parity Toggle: This toggle enables the ODD PARITY data check on the serial port for this Repeater.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 This command is used to switch the AUX PORT between selecting directly (1 of 8) instead of using binary inputs for requesting up to 255 different spiels. The direct select is useful when you have eight or less spiels which need to be called up through the AUX PORT. The AUX PORT can be wired directly to up to eight different pushbuttons.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "k" Early Starts: The user has the choice of what each card does when it is still playing a spiel and receives a new 'start' or 'loop' command. The options are: 1) DO NOTHING. 2) JUMP FORWARD to the next spiel. 3) JUMP BACKWARDS to the start of the current spiel.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 This feature defaults to an 'off' condition. ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "p" PA Zone Priorities: NOT USED WITH AB-100 AudioBrick: In the Public Address System there are a number of different ways to assign priorities to different PA STATIONS and PA zones.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ Input Triggering: "K" "L" "M" "O" "P" "Q" "R" "S" 'A' Input Closing Edge: 'A' Input Opening Edge: 'B' Input Closing Edge: 'B' Input Opening Edge: 'PB' Input Closing Edge: 'PB' Input Opening Edge: 'Aux. Port' Input Closing Edge: 'Aux.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 they will start accepting other serial commands again.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - AB-100 AudioBrick Serial Port Commands The MACs digital audio system can be controlled by simple switch closures to start and stop playback or looping, mute the audio, and perform a variety of functions. Besides this method of controlling the Repeater cards, you can talk to any or all the cards at one time through a serial data line from your computer, terminal, or control system.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 tween each character sent. Without this delay, you might over run the Digital Audio RepeatersÕ incoming data buffer. If you have hooked up the Digital Audio Repeaters to your computer and it still doesnÕt seem to respond to the keyboard, the first thing to check is that you are attached to the right serial port.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 4) Cocked - You can set a flag on any number of different cards in the digital audio system which, when set, will cause those cards to respond to commands of this type. Once cocked, you will have to uncock a card to stop it from responding to any more COCKED commands. EXAMPLE: A 'Start Cocked' command will start only those Digital Audio Repeaters which have had their 'COCKED' flags set.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - AB-100 AudioBrick Serial Commands "a" (TRACK#) Enter Setup Echo Mode: This command puts the one card addressed by the TRACK# into this mode while taking all other cards out of this mode. This is a special mode that lets you play with the command structure of the digital audio system and get an echo of all commands accepted in plain English.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 fies the operation of this one card and no other parts of the system. EXAMPLE: to put card 00 into ECHO ALL mode: e00 EXAMPLE: a 'Start Track# 00' command will echo: t00 ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "f" Exit Echo All Mode: This command takes all cards in the system out of ECHO ALL MODE.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "j" (5AA5) Special Default Setup: This command should not be used if there is more than one card in the system. It loads the configuration EEprom with the default setups. As this sets all cards to address 00, it can cause problems if invoked lightly.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 To do this, type a: xn The other cards will then start listening to you again. ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "n" (TRACK#) Memory Address Status: This command responds with the address bits 10 through 42 for the card specified by the TRACK#.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 "I" "JÓ "K" (GROUP#) Reset All: Reset Cocked: Reset Group: These commands reset the addressed card(s) to the start of their memory. If the cards are running, the reset takes place after the current 1 KByte block of sound data has played. The sound then continues from the start of the memory. A start delay will only take place after a card has received a RESET.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Cards in the system. After the cocked flags are reset, no cards in the system will respond to any COCKED commands.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ")" (TRACK#) (SPIEL#) "*" (SPIEL#) "+" (SPIEL#) "/" (GROUP#) (SPIEL#) Select Spiel Track: Select Spiel All: Select Spiel Cocked: Select Spiel Group: Up to 255 different recordings can be stored on a single card. Each of these individual recordings are called 'spiels'. These commands can be used to select an individual spiel on the selected card(s).
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 fied by the TRACK#. To use these commands to tighten the synchronization between cards, you will need to stop the clock before issuing Start Commands, and then restart the clock. If the clock remains stopped for too long, the dead man timer will time out and reset the cards. The dead man time is about 1 second.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 cards. When a valid PA request comes in to any card, it opens up the appropriate PA TRUNK LINE to feed the audio from the PA STATION to the Repeater card. This command clears the PA request by turning off the TRUNK# of the PA request. If all the trunk lines are off, then it turns off the PA LED on the front of the card and allows the mute level to return to whatever it was before.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 AB-Clock Configuration: To configure the AB-Clock through the serial port, you need to connect the system just as you do for any serial communications (see the 'AB-100 AudioBrick Serial Port Commands' section of the manual). The serial port interface on the AB-Clock is a bit different from most of the products offered by Gilderfluke & Company.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "a" Select and Play a Sound: This command is used when you just want to play any sound recorded in the AB-Clock. Valid entries are from 1 to 98 to select specific spiels, or 99 to hear whatever spiel is next in line.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "f" Pulse Output Once: This command is used when the Status Output is set to pulse once each minute to run ÔregulatorÕ or ÔremoteÕ style clocks. It will pulse the status output once to assist you in setting this style of clock.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 tolling the hours on each full hour. ÔCHIME 1Õ is the sound played for all but the last chime in a sequence, which is played as ÔCHIME 2Õ. This allows the last chime to be recorded with a much longer fade out than those which are called up by ÔCHIME 1Õ.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Sometimes the neighbors donÕt like to hear a clock tolling at all hours of the night. This command is used to set the hours during which the AB-Clock will make noise if it has been set to tick and/or tock, chime on any of the quarter hours or toll the full hours.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "K" Schedule Displayed: There are seven daily schedules and one weekly schedule in the ABClock. The daily schedules are used for the operating hours and special shows for seven days Sunday through Saturday.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 BYTE 1031 = LINE FEED ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ "O" Reload Defaults: This command is used to part or all of the memory back to its default status.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 AB-Clock Serial Port Command: This command will only be accepted by the AB-Clock when it is not already in configuration mode. "s" (TRACK#) (STRING) Load Configuration: This command loads the string that follows it into the configuration EEprom for the AB-Clock. This command is used to load the configuration into an AB-Clock.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - MX-100 / MX-200 - Memory Expansion Boards for use with AB-100 Digital Audio Repeaters A MX-100 or MX-200 Memory Expansion Board is used to increase the capacity of a Digital Audio Repeater by thirty-two additional memory chips. Any number of these memory expansion cards can be used on any Repeater card within the physical space limitations of the Repeater housing.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Configuration and Installation: Each MX- Repeater card plugs into J-5 (2 x 17 pin header) and J-4 (1 x 24 pin header) on the card below. They are mounted by four 6-32 standoffs from the card below. The Repeater card to which the first MX- card is attached must have four 6-32 x 1/2" hex standoffs attached to it.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - DR-50 MiniRepeaters power supply power supply A input + A input B input + B input output + ground output volume line output bass Mini AudioBrick treble - AB-50 Mini AudioBricks AB-50 and DR-50 MiniRepeaters are used where all you need is a fairly short sound with a good quality audio output. Their output quality is up to 15 KHz bandwidth with a dynamic range of 72 dB.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 or more sounds at any remote location. You can just screw an AB-50 to the wall, attach an amplifier and speaker and you have a completed sound system. Actual Playing Times for MiniRepeaters: The following tables show in seconds the capacities of several different types of Eproms at several different fixed bandwidths.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Configuration Dipswitches: There are two opto-isolated inputs on each MiniRepeater which can be used for starting, stopping, and resetting them. All configuration for the DR50Õs is done on an eight position Configuration Dipswitch (nine positions on the AB-50).
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 When this switch is turned on the one-shot circuit on the B input is disabled. When used in combination with other switches, it allows you to hold the repeater in a reset or stopped state through the B input. SWITCH #9: ÔA2Õ CONTINUOUS: (THIS IS A JUMPERON THE DR-50S) When this switch is turned on the one-shot circuit on the A input is disabled.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Eprom Installation: The MiniRepeaters can hold a single Eprom in any of the following sizes: 27C010 27C020 27C040 27C080 The unused upper address bits are ignored in the smaller sized chips Eproms from most manufacturers. Some manufacturerÕs chips donÕt do this, and this is where JP-1 comes into play.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Trigger Inputs: Each J6 cable is arranged in the following order. The inputs to the DR-50s are optisolated. You must provide a 12 to 24 VDC voltage to pins 10, 20, 30 and 40 of each cable. To protect the DR-50s from spikes on these connections, we reccomend an isolated power supply should be used for these connections.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 AB-50 Connections: The inputs and outputs on an AB-50 are connected as follows: 1) power supply 2) power supply 3) A input positive 4) A input negative 5) B input positive 6) B input negative 7) Positive audio output 8) Ground 9) Negative audio output The power supply connections need to be made to a 12 to 18 VAC transformer (supplied with the AB-50).
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - SNDCMP8.EXE - Eight Bit Digital Audio Compressor for use with AB-100 Digital Audio Repeaters and DR-50 or AB-50 Mini Audio Repeaters The Eight Bit Digital Audio Compressor is a small utility program which is 3 4 used to convert standard sixteen bit 44.1 KHz mono .WAV and .
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 The Omit Flag Byte CheckBox should only be used when programming samples for our 1.0 revision repeaters. This can also be used for burning Eproms for some of our competitorÕs repeaters. There are five commands buttons available on the SNDCMP8 main window. These are: 1) Add: This brings up a standard Macintosh/Windows file open dialog. You can select any sixteen bit 44.1KHz mono .WAV or .
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 Any of the previously ÔADDedÕ sample files can be highlighted on the SNDCMP8 main window. The length of the sample will then be displayed and you can set the Sample and Filter Rate, Silence Threshold and Rounding for each sample. If more than one sample is selected the Sample Length will change to show the total length of all the selected samples. Any changes will effect all the selected samples.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 ed up (padded out with silence) or down (lopped off at the closest one KByte boundary) once the sound is converted to the final sample rate. This checkbox can be used to make sure that no silence is appended onto the end of a looping sample.
GILDERFLUKE & CO. ¥ 205 S. FLOWER ¥ BURBANK, CA 91502-2102 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485 - Internal Details The format of the data which is burned into the Eproms is in blocks of 1 KByte each. The first byte of the audio data is normally replaced by one flag byte. This sets the operating settings for the following 1023 audio data bytes. Bits 0 to 2 set the sample rate, while bits 3 to 5 set the output filter cutoff point. The last two bits flag the ends of samples.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.
GILDERFLUKE & CO. ¥ 205 S.