Hot, Room and Cold Bottled Water Cooler Model # 75IECHK-SC-SP USER MANUAL TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE, USER MUST READ THIS MANUAL BEFORE ASSEMBLING, INSTALLING & OPERATING DISPENSER. SAVE FOR FUTURE USE IMPORTANT: Do NOT Return Dispenser To Store. PN 75IECHK-SC-SP © 2012 Electrotemp Technologies Inc.
Model # 75IECHK-SC-SP :Page 2 SAFETY PRECAUTIONS To reduce risk of injury and property damage, user must read this entire manual before assembling, installing & operating dispenser. Failure to execute the instructions in this manual can cause personal injury or property damage. This product dispenses water at very high temperatures. Failure to use properly can cause personal injury.
Model # 75IECHK-SC-SP :Page 3 SAFETY PRECAUTIONS ---Electrical Requirements Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended.
Model # 75IECHK-SC-SP :Page 4 TABLE OF CONTENTS Safety Precautions ………......…………………… 2 Safety Precautions-Electrical Requirements … 3 Key information for future use..................……… 4 Specifications ……….............................………… 5 Parts & Features ……….......................………….. 5 Assembly ……………......................……………… 6 Cleaning prior to initial use ………..................…. 6 Installation …………………......................………. 7 Operation …………………….......................……..
Model # 75IECHK-SC-SP :Page 5 SPECIFICATIONS Power Supply 6A Refrigerant Type R-134A Cold Water Power 100 Watts Cold Capacity / Hour 4L / 1.06 Gallon Cold Temp Range 3°C – 10°C / 37.4°F - 50°F Hot Water Power 650 Watts Hot Capacity / Hour 7L(>80℃) / 1.85 Gallon (>176°F) Hot Temp Range 85°C – 95°C / 185°F - 203°F Dimensions 297 (W) x 322 (D) x 1000 (H)mm (Not including feet) 11.7 (W) x 12.7 (D) x 39.4 (H)inch (Not including feet) Net Weight 32.8 Ibs / 14.9 kg.
Model # 75IECHK-SC-SP :Page 6 ASSEMBLY WARNING Keep plastic bags away from children. 1. Remove dispenser from packaging. 2. Unpack drip tray and insert into dispenser. 3. Properly dispose all of packaging. CLEANING PRIOR TO INITIAL USE To remove any odors or dust that may collect during shipment, you must clean dispenser prior to first use. DO NOT PLUG THE COOLER INTO AN ELECTRICAL POWER OUTLET Time Required: 40 minutes. 1. Remove bottle receptacle by turning it counter clockwise and pulling up.
Model # 75IECHK-SC-SP :Page 7 INSTALLATION CAUTION To prevent accidental tip hazard, dispenser must be securely anchored to wall as shown. 1. Place dispenser upright. 2. Locate dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. Notice: Do NOT plug in power cord yet. 3. Position dispenser so the back is at least 4 inches from wall and there are at least 4 inches of clearance on both sides. 4.
Model # 75IECHK-SC-SP :Page 8 1. Remove tamper seal from bottle cap. Do NOT remove plastic cap. 2. Clean bottle cap and neck with a soft cloth and warm soapy water, then rinse. 3. Lift bottle and insert onto the probe. Apply slight pressure until the plug inside the cap pushes in and the bottle is seated. Water will begin to flow into the reservoirs causing air bubbles to form in the bottle. 4. Plug cord into a properly grounded wall outlet. 5. Turn energy saving switch on back of dispenser to ON.
Model # 75IECHK-SC-SP :Page 9 PROPER CARE & CLEANING General Cleaning Perform: As needed Time Required: 5 minutes. Note: Do NOT use abrasive materials or chemical cleaners. 1. Clean cabinet surfaces with a soft cloth and warm soapy water, then rinse. 2. Wipe dust from back of dispenser to improve efficiency. 3. Remove drip tray assembly by pulling it forward. Remove cover. Place tray and cover in dishwasher or wipe parts clean with a soft cloth and warm soapy water.
Model # 75IECHK-SC-SP :Page 10 11. Wipe inside of reservoir and area around both taps with a soft cloth using the mixture of one gallon tap water and 1 tablespoon unscented household bleach. If there is mineral build-up (white chalky deposits) use a household product designed to remove calcium, lime or rust. These can be found in grocery and hardware stores. Follow manufacturer’s label instructions. 12. Pour the one gallon tap water and 1 tablespoon unscented household bleach mixture into the reservoir.
Model # 75IECHK-SC-SP :Page 11 TROUBLESHOOTING Dispenser does not operate. • Make sure the power cord is properly connected to a working outlet. Water is leaking • Call 888-828-1426 for assistance. Push buttons are stuck and/or faucets are leaking. • Apply mineral oil (baby oil) to button slides to reduce friction. No water is coming from the taps. • Make sure the bottle is not empty. If so replace it. • Make sure to push the water controls in fully. • Remove bottle receptacle as per page 6 step 1.
Model # 75IECHK-SC-SP :Page 12 LIMITED WARRANTY Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship.
版本号 修订 A 修订内容 对应铭牌,重量由13.8Kg更改为14.