Model# 65470W-6101 65470W-6104 65470W-6127H2 SKU# 703414 703435 703417 INSTALLATION AND CARE GUIDE TWO-HANDLE LAVATORY FAUCET Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this lavatory faucet.
Table of Contents Important Information ..............................2 Warranty ...................................................2 Pre-Installation .........................................2 Planning Installation ..............................2 Tools and Hardware Required ...............2 Package Contents ..................................3 Installation ................................................4 Operation...................................................7 Care and Cleaning ......................
Pre-Installation (continued) PACKAGE CONTENTS Drain Assembly Faucet Assembly D* A N J E* L M F* B I* G* C K H* NOTE: *Items D - I come pre-assembled. Part Quantity Part Description Quantity A Description Faucet 1 H Drain body 1 B Gasket 1 I Ball nut 1 C Mounting nut 2 J Ball rod 1 D Pop up stopper 1 K Spring clip 1 E Drain flange 1 L Thumb screw 1 F Rubber washer 1 M Lift rod strap 1 G Lock nut 1 N Lift rod 1 3 HOMEDEPOT.
Installation 1 Installing the faucet assembly 2 Preparing the pop-up assembly CAUTION: Always turn off the water supply before removing an existing faucet or replacing any part of a faucet. Open the faucet handle to relieve water pressure and ensure that the water is completely shut off. □ Shut off the water supply. Remove the old faucet. □ Clean the mounting surface. □ Ensure the gasket (B) is on the bottom of the new faucet (A). □ Place the faucet (A) through the mounting holes in the sink.
Installation (continued) 3 Installing the drain body □ Apply silicone sealant (not included) under the drain flange (E) and place the drain flange (E) into the drain hole of the sink. □ From underneath the sink, screw the drain body (H) onto the drain flange (E). Ensure that the opening (1) for the ball rod on the drain body (H) faces towards the rear of the sink. NOTE: In shallow cabinet installations, the ball rod (J) may need to be shortened.
Installation (continued) 5 Installing the lift rod □ 6 Attaching the ball rod and strap Insert the lift rod (N) through the faucet (A) and down into the lift rod strap (M). Tighten the thumb screw (L). □ Attach the ball rod (J) to the lift rod strap (M) using the spring clip (K). M N K J 2 3 1 M 1 1 2 L N A 7 Adjusting the lift rod □ Loosen the thumb screw (L) on the lift rod strap (M). □ Push down on the lift rod (N) until the drain stopper is in the open position.
Installation (continued) the water supply 8 Making connections □ □ Use 1/2 in. I.P.S. faucet connections (2), or use supply line coupling nuts (3) (not included) with a 3/8 in. O.D. ball-nose riser (1). Use wrenches to tighten the connections. Do not overtighten. 1 3 2 Operation 1 Flushing and checking for leaks IMPORTANT: After installation is complete, remove the aerator to flush the water lines. Do not lose the gasket (1) in the aerator.
Care and Cleaning □ To clean, wipe down with a damp cloth and towel dry. □ Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will be voided. Troubleshooting NOTE: Refer to the service parts section in this manual for a detailed drawing showing the location of the parts listed below. Problem Possible Cause There are leaks from the handle. The bonnet nut has come loose and/or the washer is dirty or damaged. □ □ Clean or replace the washer.
Service Parts 2 14 3 1 4 5 6 7 Faucet ID tags can be found by removing the hot water handle 8 9 12 13 10 11 Part Part Number Part Description Part Number 1 Description Index H RP10001* 9 Cartridge C RP20014 2 Index C RP10002* 10 Gasket RP80205 3 Screw RP50005 11 Mounting nut RP56001 4 Handle RP13246* 12 Aerator RP30216* 5 Inverter RP64044 6 Bonnet nut RP70193 13 Drain assembly less lift rod RP40027* 14 Lift rod RP40161* 7 Washer RP64124 8 Cartridge H R
Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Retain this manual for future use.
Modelo núm. 65470W-6101 65470W-6104 65470W-6127H2 SKU núm. 703414 703435 703417 GUÍA DE USO Y MANTENIMIENTO GRIFO PARA LAVAMANOS, DE DOS LLAVES ¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Tabla de contenido Información importante .........................12 Garantía...................................................12 Pre-instalación .......................................12 Planificación de la instalación .............12 Herramientas y herrajes necesarios ....12 Contenido del paquete .........................13 Instalación ..............................................14 Funcionamiento ......................................17 Cuidado y limpieza ................................
Pre-instalación (continuación) CONTENIDO DEL PAQUETE Ensamblaje del drenaje Ensamblaje de la mezcladora D* A N J E* L M F* B I* G* C K H* NOTA: *Los artículos D - I vienen preensamblados.
Instalación instalar el ensamblaje preparar el ensamblaje 1 Cómo 2 Cómo del grifo emergente PRECAUCIÓN: Cierra siempre el suministro de agua antes de quitar un grifo existente o reemplazar cualquier pieza de un grifo. Abre la llave del grifo para liberar la presión de agua y asegúrate de que el suministro de agua esté completamente cerrado. □ Cierra el suministro de agua. Retira el grifo anterior. □ Limpia la superficie de montaje.
Instalación (continuación) instalar el cuerpo del instalar el tapón y la 3 Cómo 4 Cómo drenaje varilla de bola □ Aplica sellador de silicona (no incluido) debajo de la brida del drenaje (E) y coloca ésta dentro del orificio de drenaje del lavabo. □ Desde la parte inferior del lavabo, enrosca el cuerpo del drenaje (H) en la brida del drenaje (E). Asegúrate de que la abertura (1) para la varilla de bola del cuerpo del drenaje (H) esté frente a la parte posterior del lavabo.
Instalación (continuación) instalar la varilla de 5 Cómo elevación □ fijar la varilla de bola 6 Como y la correa Inserta la varilla de elevación (N) a través de la mezcladora (A) y de la correa de la varilla de elevación (M). Aprieta el tornillo de ajuste manual (L). □ Fija la varilla de bola (J) a la correa de la varilla de elevación (M) con el sujetador de resorte (K).
Instalación (continuación) hacer las conexiones 8 Cómo del suministro de agua □ Usa conexiones de grifos de 1/2" IPS (2) o tuercas de acoplamiento de líneas de suministro (3) (no incluidas) con un tubo montante de bola de diámetro exterior de 3/8" (1). □ Usa llaves para apretar las conexiones. No aprietes demasiado. 1 3 2 Funcionamiento 1 Cómo purgar las tuberías y comprobar que no haya fugas IMPORTANTE: Después de terminar la instalación, retira el aireador para purgar las tuberías de agua.
Cuidado y limpieza □ Para limpiar, usa un paño húmedo y seca con una toalla. □ No uses limpiadores abrasivos, esponjas de alambre o productos químicos fuertes para limpiar esta mezcladora, pues ello anulará la garantía. Solución de problemas NOTA: Consulta la sección de piezas de repuesto de este manual para ver un dibujo detallado que muestra la ubicación de las piezas enumeradas a continuación. Problema Posible causa Hay filtración por el maneral.
Piezas de repuesto 2 14 3 1 4 5 6 Las etiquetas de identificación de la mezcladora pueden verse al quitar el maneral del agua caliente.
¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Conserva este manual para uso futuro.
Modèle n° 65470W-6101 65470W-6104 65470W-6127H2 UGS n° 703414 703435 703417 GUIDE D’INSTALLATION ET D’ENTRETIEN ROBINET DE LAVABO À DEUX MANETTES Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelez le service à la clientèle Glacier Bay entre 8 h et 19 h, HNE, du lundi au vendredi au entre 9 h et 18 h, HNE, le samedi au 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM THANK YOU Nous vous remercions d'avoir fait confiance à Glacier Bay en achetant ce robinet de salle de bains.
Table des matières Information importante ..........................22 Garantie...................................................22 Pré-installation .......................................22 ................22 Outils et quincaillerie requis ................22 Contenu de l’emballage .......................23 Installation ..............................................24 Utilisation ................................................27 Entretien et nettoyage ............................28 Dépannage ............
Pré-installation (suite) CONTENU DE L'EMBALLAGE Évacuation Robinet D* A N J E* L M F* B I* G* C K H* REMARQUE : *Les articles D à I sont fournis pré-assemblés.
Installation de l'ensemble de de l'évacuation 1 Installation 2 Préparation robinetterie mécanique ATTENTION : Coupez l’alimentation en eau CAUTION: Always turntoujours off the water supply before avant d’enlever un robinet ou de any remplacer removing an existing faucetexistant or replacing part of a n’importe quelle partie du robinet. Ouvrez la poignée du faucet.
Installation (suite) du corps 3 Installation d'évacuation de la bonde et de 4 Installation la tige à rotule Appliquez du mastic à la silicone (non compris) sous la bride d’évacuation (E) et placez la bride d’évacuation (E) dans le trou d’évacuation de l’évier. □ À partir du dessous de l’évier, vissez le corps d’évacuation (H) sur la bride d’évacuation (E). Assurez-vous que l’ouverture (1) de la tige à rotule du corps d’évacuation (H) fait face à l’arrière de l’évier.
Installation (suite) de la tige à rotule et 5 Installation de la tige de levage 6 Fixation sangle □ Insérez la tige de levage (N) à travers le robinet (A) puis dans la sangle de la tige de levage (M). Vissez la vis à oreilles (L). □ Attachez la tige à rotule (J) à la sangle de la tige de levage (M) au moyen de la pince à ressort (K). M N K J 2 3 1 M 1 1 2 L N A 7 Réglez la tige de levage □ Desserrez la vis à oreilles (L) de la sangle de la tige de levage (M).
Installation (suite) des conduites 8 Raccordement d’alimentation en eau □ Utilisez des raccords de robinet IPS de 1,27 cm (½ po) (2), ou utilisez des écrous d'accouplement pour conduite d'alimentation (3) (non compris) avec une colonne montante à bout sphérique de D.E. 9,53 mm (3/8 po) (1). □ Utilisez la clé pour serrer les raccords. Ne serrez pas trop.
Entretien et nettoyage □ Pour nettoyer, essuyez simplement avec un linge humide et séchez avec une serviette. □ N'utilisez pas de nettoyants abrasifs, de la laine d’acier ou de produits chimiques abrasifs pour nettoyer ce robinet, sinon la garantie sera annulée. Dépannage REMARQUE : Consultez la section pièces de rechange de ce guide pour une illustration détaillée de l’emplacement des pièces énumérées ci-dessous. Problème Cause possible La manette fuit.
Pièces de rechange 2 14 3 1 4 5 6 Les étiquettes d’identité du robinet sont repérées en retirant la manette d’eau chaude.
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelez le service à la clientèle Glacier Bay entre 8 h et 19 h, HNE, du lundi au vendredi au entre 9 h et 18 h, HNE, le samedi au 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Conservez ce manuel pour référence future.