Model# 67392W-6A04 SKU# 125344 INSTALLATION AND CARE GUIDE TWO-HANDLE LAVATORY FAUCET Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM/GLACIERBAY THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this lavatory faucet.
Table of Contents Important Information ..............................2 Warranty ...................................................2 Pre-Installation .........................................2 Planning Installation ..............................2 Tools and Hardware Required ...............2 Package Contents ..................................3 Installation ................................................4 Operation...................................................9 Care and Cleaning ......................
Pre-Installation (continued) PACKAGE CONTENTS Drain Assembly Faucet Assembly S B J* A D E F Q K* C G T R H L* M* I P O N* NOTE: *Items J - N come pre-assembled.
Installation 1 Installing the faucet assembly 2 Installing the faucet handles CAUTION: Always turn off the water supply before removing an existing faucet or replacing any part of a faucet. Open the faucet handle to relieve water pressure and ensure that the water is completely shut off. Shut off the water supply. Remove the old faucet. □ Clean the mounting surface. □ Remove the preassembled lock nut (H) and washers (G) from the new faucet (A).
Installation (continued) 3 Preparing the pop-up assembly 4 Installing the drain body Remove the pop up stopper (J) and drain flange (K) from the drain body (N). J □ Apply silicone sealant (not included) under the drain flange (K) and place the drain flange (K) into the drain hole of the sink. □ From underneath the sink, screw the drain body (N) onto the drain flange (K). Ensure that the opening (1) for the ball rod on the drain body (N) faces towards the rear of the sink.
Installation (continued) 6 Installing the lift rod the stopper and 5 Installing horizontal rod □ Before installation, unscrew the protective cap (1) from the horizontal rod (P). □ Insert the stopper (J) into the drain hole in the sink. □ Insert the horizontal rod (P) into the drain body (N) and through the hole of the stopper (J) until you hear a click. See insert 2. You can press the two sides of the joint (O) to remove the horizontal rod (P).
Installation (continued) 7 Attaching the horizontal rod and strap □ Press the horizontal rod (P) down to ensure the stopper (J) is in the maximum open position. □ Slide the clip (R) upward, adjust the location of the lift rod strap (Q) to the appropriate height and insert the horizontal rod (P) with the correct hole of the lift rod strap (Q). □ Move the lift rod strap (Q) in or out to choose an appropriate location. □ Slide the clip (R) downward until it secures with the horizontal rod (P).
Installation (continued) the operation of the 9 Checking pop up □ Operate the lift rod (S) up and down to verify that the stopper (J) opens and closes correctly. S J 10 □ □ Attaching the quick connecting hose Attach the quick connecting hose (I) connections to the hot faucet handle (B) connection, faucet body (A) connection, and cold faucet handle (C) connection. Push until the connections snap together. C A B Pull down moderately to ensure the connection has been made.
Installation (continued) 11 □ Making the water supply connections Use 1/2 in. I.P.S. faucet connections (2), or use supply line coupling nuts (3) (not included) with a 3/8 in. O.D. ball-nose riser (1). 1 NOTE: Before tightening the faucet connector to the water supply, apply a second wrench to the supply tube fitting. This will prevent the supply tube from moving or twisting when tightening the faucet connector. Do not overtighten.
Operation (continued) 2 Removing the quick connector □ If it is necessary to remove the quick connector (1), squeeze the tabs (2) on the quick connector and then pull down to disconnect. 2 Squeeze Pull down 1 1 Care and Cleaning □ To clean, wipe down with a damp cloth and dry with a towel. □ Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will be voided.
Service Parts 1 2 3 4 19 5 6 7 11 12 13 Faucet ID tags can be found on the hot water inlet 14 15 16 17 8 18 9 10 Part 1 Description Handle Part Number Part Description RP13149* 11 Aerator Part Number RP30191 2 Set screw RP50002 12 Plastic wrench RP30040 3 Connector RP50003 13 Washer RP64193 4 Inverter RP64044 14 Lock nut RP56062 5 Bonnet nut RP70193 15 Block RP70421 6 Cartridge H RP20067 16 O-ring RP60002 7 Cartridge C RP20068 17 Quick connecting hose RP70
Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM/GLACIERBAY Retain this manual for future use.
Modelo núm. 67392W-6A04 SKU núm. 125344 GUÍA DE USO Y MANTENIMIENTO GRIFO PARA LAVAMANOS, DE DOS LLAVES ¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM/GLACIERBAY GRACIAS Agradecemos la confianza que has depositado en Glacier Bay al comprar este grifo para lavamanos.
Tabla de contenido Información importante .........................14 Garantía...................................................14 Pre-instalación .......................................14 Planificación de la instalación .............14 Herramientas y herrajes necesarios ....14 Contenido del paquete .........................15 Instalación ..............................................16 Funcionamiento ......................................21 Cuidado y limpieza ................................
Pre-instalación (continuación) CONTENIDO DEL PAQUETE Ensamblaje de la mezcladora Ensamblaje del drenaje S J* B A D E F Q K* C G T R H L* M* I P O N* NOTA: *Los artículos J - N vienen preensamblados.
Instalación instalar el ensamblaje instalar las llaves del 1 Cómo 2 Cómo del grifo grifo PRECAUCIÓN: Cierra siempre el suministro de agua antes de quitar un grifo existente o reemplazar cualquier pieza de un grifo. Abre la llave del grifo para liberar la presión de agua y asegúrate de que el suministro de agua esté completamente cerrado. NOTA: La válvula de agua caliente está identificada con una etiqueta. □ Cierra el suministro de agua. Retira el grifo anterior. Limpia la superficie de montaje.
Instalación (continuación) preparar el ensamblaje instalar el cuerpo del 3 Cómo 4 Cómo emergente drenaje Retira el tapón emergente (J) y la brida del desagüe (K) del cuerpo de desagüe (N). J □ Aplica sellador de silicona (no incluido) debajo de la brida del drenaje (K) y coloca ésta dentro del orificio de drenaje del lavabo. □ Desde la parte inferior del lavabo, enrosca el cuerpo del drenaje (N) en la brida del drenaje (K).
Instalación (continuación) instalar la varilla de 6 Cómo elevación instalar el tapón y la 5 Cómo varilla horizontal □ Antes de la instalación, desenrosca la tapa protectora (1) de la varilla horizontal (P). □ Inserta el tapón (J) en el orificio del drenaje del lavabo. Inserta la varilla horizontal (P) en el cuerpo del desagüe (N) y a través del orificio del tapón (J) hasta que escuches un clic. Consulta el folleto 2. Puedes presionar ambos lados de la junta (O) para retirar la varilla horizontal (P).
Instalación (continuación) 7 Cómo instalar la varilla horizontal y la correa □ Presiona hacia abajo la varilla horizontal (P) para garantizar que el tapón (J) esté abierto completamente. □ Desliza la presilla (R) hacia arriba, ajusta la ubicación de la correa de la varilla de elevación (Q) a la altura adecuada e inserta la varilla horizontal (P) con el orificio correcto de la varilla de elevación (Q).
Instalación (continuación) 9 □ Cómo verificar el funcionamiento del drenaje emergente S Mueve la varilla de elevación (S) hacia arriba y abajo para verificar que el tapón (J) se abre y cierra correctamente. J 10 □ □ Cómo montar la manguera de conexión rápida Conecta las conexiones de la manguera de conexión rápida (I) a la conexión de la llave de agua caliente (B), la conexión del cuerpo del grifo (A) y a la conexión de la llave de agua fría (C).
Instalación (continuación) 11 □ Cómo hacer las conexiones del suministro de agua Usa conexiones de grifos de 1/2" IPS (2) o tuercas de acoplamiento de líneas de suministro (3) (no incluidas) con un tubo montante de bola de diámetro exterior de 3/8" (1). 1 NOTA: Antes de apretar el conector del grifo al suministro de agua, fija el accesorio de la tubería de suministro colocando una segunda llave . Esto evitará que la tubería de suministro se mueva o gire cuando aprietes el conector del grifo.
Funcionamiento (continuación) 2 Cómo quitar el conector rápido □ Si es necesario, retira el conector rápido (1), aprieta las pestañas (2) de la manguera y hala hacia abajo para desconectar. 2 Aprieta Hala hacia abajo 1 1 Cuidado y limpieza □ Para limpiar, usa un paño húmedo y seca con una toalla. □ No uses limpiadores abrasivos, esponjas de alambre o productos químicos fuertes para limpiar esta mezcladora, pues ello anulará la garantía.
Piezas de repuesto 1 2 3 4 19 5 6 7 11 12 13 Las etiquetas de identificación de la mezcladora pueden encontrarse en la entrada de agua caliente.
¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM/GLACIERBAY Conserva este manual para uso futuro.