Model# 67536-0508D2 HD67536-0501 HD67536-0527H2 SKU# 1001407752 304236320 304236333 INSTALLATION AND CARE GUIDE TOUCHLESS LED SINGLE-HANDLE PULL-DOWN SPRAYER KITCHEN FAUCET Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Table of Contents Important Information ..............................2 Warranty ...................................................2 Pre-Installation .........................................2 Planning Installation ..............................2 Tools and Hardware Required ...............2 Package Contents ..................................3 Installation ................................................4 Operation ..................................................14 Care and Cleaning .....................
Pre-Installation (continued) PACKAGE CONTENTS A Sensor Control Box Soap Pump Assembly O L F M P G N Q H K I B J C D R E Part Description Quantity A Faucet body 1 B Washer 2 C Nut D Protective cap Part Description Quantity K Quick connect assembly 1 1 L Sensor control box 1 1 M Battery pack 1 "AA" Battery 4 E Wrench 1 N F Escutcheon 1 O Soap pump 1 G Gasket 1 P Soap assembly 1 H Hose 1 Q 1 I Weight clip 1 Soap dispenser mounting nut J Weig
Installation 1 Preparing for installation CAUTION: Always shut off the water supply before removing an existing faucet or replacing any part of a faucet. Open the faucet handle to relieve water pressure and ensure that the water is completely shut off. □ Shut off the water supply. Remove the old faucet. Clean the mounting surface. □ Before installation, remove the quick connector (K) from the free end of the hose by unscrewing it in a counterclockwise direction.
Installation (continued) 3 Securing the faucet assembly □ Install the washers (B) onto the threaded shank. □ Push the hose (H) up through the faucet body until the end of the hose is flush with the bottom on the shank (1) so it's out of the way for the next step. □ Thread the mounting nut (C) onto the shank using the wrench (E) provided to tighten firmly. 1 B H C C 3 B 1 2 E 5 E HOMEDEPOT.COM/GLACIERBAY Please contact 1-855-HD-GLACIER for further assistance.
Installation (continued) the quick connector 4 Installing the protective cap 5 Attaching to the hose □ Screw the protective cap (D) onto the threaded mounting shank (1). □ Pull out the hose (H) from the threaded mounting shank (1). □ Attach the quick connector (K) by screwing it onto the threaded end of the hose (H) in a clockwise motion. Hand tighten only.
Installation (continued) 6 Installing the sensor cable NOTE: The side of the control box (L) with "in" and "out" showing must face the front of the cabinet (away from the back of the cabinet). □ Install the sensor cable (1) to the control box connection (2). Ensure the arrows on the sensor cable and control box connection are aligned to one another to ensure proper installation. Ensure they are tightly connected by firmly pushing together.
Installation (continued) the quick connector 7 Attaching to the receiving block □ Connect the hose with the yellow tag to the hose on the control box (L) with a matching yellow tag. Push firmly together until they snap into place. As shown in the Fig 1. □ Connect the hose with the green tag to the hose on the control box (L) with a matching green tag. Push firmly together until they snap into place. As shown in the Fig 1.
Installation (continued) 8 Installing the batteries NOTE: This step is for battery installation (optional). If the battery will not be used, install as described in step 11. □ To open the battery housing, squeeze the sides while pulling the cover (1). DO NOT pull on the wire. See figure 1. □ Install the four AA batteries (N) included by matching the positive (+) and Negative (-) ends on the battery (N) to the (+) and (-) markings in the battery pack (M).
Installation (continued) 9 Installation using the battery pack NOTE: This step is for battery installation (optional). If the battery will not be used, install as described in step 11. □ Insert the battery pack cable (1) into the control box connection (2). NOTE: After installing the battery pack, the light on the sensor will flash and the faucet control box will make a "click" sound when you move your hand in the sensor area. If not, check to ensure the batteries are installed correctly.
Installation (continued) 10 Placing the battery pack into the battery pack seat NOTE: This step is for battery installation (optional). If the batteries will not be used, skip to step 11. Before installation, select the location for the battery pack seat (1) and verify that the battery pack (M) will reach battery pack seat (1). □ There are 2 options to secure the battery pack (M) under the counter: Tape Installation or Screw Installation.
Installation (continued) using the AC 11 Installation adapter (not included) NOTE: This step is for installation without batteries using an AC adapter (not included). If using the batteries, install as instructed in step 8 and skip to step 12. The AC adapter is not included with the product, but can be purchased from Homedepot.com. □ Insert the AC adapter cable (1) into the control box port (2). □ Install the AC adapter (3) into the power outlet.
Installation (continued) 12 Installing the weight □ Install the weight clip (I) at the point of the hose (H) marking “weight here”. □ Insert the weight (J) onto the clip (I) by sliding it down onto the clip (I). Weight here J I Weight here H 13 Installing the soap dispenser □ □ O Insert the soap assembly (P) through the selected hole in the sink. Secure the soap assembly to the sink with the soap dispenser mounting nut (Q) provided.
Installation (continued) 14 Making the water supply connections NOTE: The hot side inlet tube is indicated by a label. Avoid twisting wires together or placing the wires close to each other and damaging. □ Thread the nut (1) on the supply line onto the outlet of the water supply valve (2) and tighten with a wrench. Do not overtighten. 1 2 H C Operation 1 Flushing and checking for leaks 01 min. 45 15 30 IMPORTANT: After installation is completed, turn on the hot and cold water supplies.
Operation (continued) 2 Operating the sensor 0 3 min. 45 15 30 NOTE: The sensor is active only when the handle is in the ON position. □ Turn the handle (1) away from the faucet to the full on position. Turn the water on by activating the sensor (2) by waving your hand within 8 inches of the sensor. □ Pulling the handle towards yourself will turn the water to cold. Pushing the handle away from yourself will turn the water to hot.
Troubleshooting will not shut off when The light on the sensor is 1 Water turning the handle to the OFF 2 flashing continuously position □ □ When you turn the handle to the full on position, the water will turn on. If the handle is closed, turn the handle to the on position and move your hand in the sensor area. If the sensor flashes 10 times continuously and slowly, then replace the 4 "AA" batteries.
Troubleshooting (continued) There is a low flow of water or sensor is not activating 4 3 The LED indicator in the spray head the water flow □ When you turn the handle to the full on position, the water will turn on. □ However, when you move your hand in front of the sensor, the water does not turn off as it should. is not functioning □ This could indicate that the washer in the "in" end of the control box is dirty or damaged. Remove the hose and unscrew the connector.
Service Parts 23 2 3 1 24 4 19 5 6 7 20 8 25 9 13 14 Faucet ID tags can be found on the hot water inlet 15 22 17 11 18 12 Description 21 16 10 Part 26 Part Number 1 Spray head and Hose RP38223* 2 Wearable ring RP70380 3 O-ring 4 5 Part Description Part Number 15 Quick connect assembly RP70680 RP60071 16 O-ring RP60089 Cartridge RP20005 17 Weight clip RP70609 Bonnet nut RP70533 18 Weight RP70441 6 Cap RP80028* 19 Escutcheon RP80441* 7 Handle RP13
Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM/GLACIERBAY Retain this manual for future use.
Modelo núm. 67536-0508D2 HD67536-0501 HD67536-0527H2 SKU núm. 1001407752 304236320 304236333 GUÍA DE USO Y MANTENIMIENTO MEZCLADORA PARA COCINA, CON ROCIADOR RETRÁCTIL, UN SOLO MANERAL, LUZ LED Y ACTIVACIÓN SIN TOCAR. ¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Tabla de contenido Información importante .........................21 Garantía...................................................21 Pre-instalación .......................................21 Planificación de la instalación .............21 Herramientas y herrajes necesarios ....21 Contenido del paquete .........................22 Instalación ..............................................23 Funcionamiento ......................................33 Cuidado y limpieza ................................
Pre-instalación (continuación) CONTENIDO DEL PAQUETE A Caja de control del sensor Ensamblaje de la bomba para jabón O L F G M P H N K I B J C D Q R E Pieza Descripción Cantidad A Cuerpo del grifo 1 B Arandela 2 C Tuerca D Tapa protectora Pieza Descripción Cantidad L Caja de control del sensor 1 1 M Paquete de baterías 1 1 N Batería “AA” 4 O Bomba para jabón 1 P Ensamblaje para jabón 1 E Llave 1 F Placa protectora 1 G Junta 1 H Manguera 1 I Sujeta
Instalación prepararse para la 1 Cómo instalación PRECAUCIÓN: Cierra siempre el suministro de agua antes de retirar un grifo existente o reemplazar alguna parte del mismo. Abre la llave del grifo para liberar la presión de agua y asegúrate de que el suministro de agua esté completamente cerrado. □ Cierra el suministro de agua. Retira el grifo anterior. Limpia la superficie de montaje.
Instalación (continuación) 3 Cómo fijar el ensamblaje del grifo □ Instala las arandelas (B) en el vástago roscado. □ Empuja la manguera (H) hacia adentro del cuerpo del grifo hasta que el extremo de aquella quede a ras con la parte inferior del vástago (1) y así no obstruya el siguiente paso. □ Enrosca la tuerca de montaje (C) en el vástago usando la llave (E) incluida para ajustar fuertemente. 1 B H C C 3 B 1 2 E 24 E HOMEDEPOT.
Instalación (continuación) instalar la tapa 4 Cómo protectora □ montar el conector 5 Cómo rápido en la manguera Enrosca la tapa protectora (D) en el vástago de montaje roscado (1). □ Hala la manguera (H) hacia fuera del vástago roscado de montaje (1). □ Fija el conector rápido (K) enroscándolo en el extremo roscado de la manguera (H) en dirección de las agujas del reloj. Ajusta únicamente con la mano.
Instalación (continuación) 6 Cómo instalar el cable del sensor NOTA: El lateral de la caja de control (L) con las indicaciones “adentro” (“in“) y “afuera” (“out“) debe estar hacia el frente del gabinete (alejado de la parte posterior de este). □ Instalar el cable sensor (1) a la conexión de la caja de control (2). Asegurar que las flechas en el cable del sensor y la conexión de la caja de control queden alineadas una con otra para garantizar instalación adecuada.
Instalación (continuación) montar el conector 7 Cómo rápido al bloque receptor □ Conecta la manguera con la etiqueta amarilla con la manguera de la caja de control (L) que tiene una etiqueta amarilla similar. Únelas con firmeza hasta que encajen en su lugar. Como se muestra en la Fig. 1. □ Conecta la manguera con la etiqueta verde con la manguera de la caja de control (L) que tiene una etiqueta verde similar. Únelas con firmeza hasta que encajen en su lugar. Como se muestra en la Fig. 1. Fig.
Instalación (continuación) 8 Cómo instalar las baterías NOTA: Este paso es para la instalación con baterías (opcional). Si no usas baterías, realiza la instalación como se describe en el paso 11. □ Para abrir el compartimento de la batería. Aprieta las partes laterales mientras halas la cubierta (1). NO hales por el cable. Ver la figura 1.
Instalación (continuación) usando las 9 Instalación baterías NOTA: Este paso es para la instalación con baterías (opcional). Si no usas baterías, realiza la instalación como se describe en el paso 11. □ Inserta el cable del paquete de las baterías (1) en la conexión de la caja de control (2). NOTA: Después de instalar el paquete de baterías, la luz del sensor parpadeará y la caja de control de la mezcladora emitirá un sonido "clic" al moverse la mano en el área del sensor.
Instalación (continuación) colocar las baterías 10 Cómo en su base NOTA: Este paso es para la instalación con baterías (opcional). Si no se van a usar baterías, continúa con el paso 11. Antes de la instalación, selecciona el lugar para la base de las baterías (1) y verifica que el paquete de baterías (M) alcanzará la base (1). □ □ □ Existen 2 opciones para asegurar el paquete de baterías (M) debajo del mostrador: Instalación con cinta o instalación con tornillos.
Instalación (continuación) usando el 11 Instalación Adaptador CA (no incluido) NOTA: Este paso es para la instalación sin baterías usando un adaptador CA (no incluido). Si usas las baterías, instala como se indica en el paso 8 y salta al paso 12. El adaptador de CA no está incluido en el producto, pero puede comprarse en Homedepot.com. □ Inserta el cable adaptador de CA (1) en el puerto de la caja de control (2). □ Enchufa el adaptador de CA (3) en el tomacorriente.
Instalación (continuación) 12 Instalar la peso □ Instala el sujetador de la peso (I) en la punta de la manguera (H) marcada “weight here” (peso aquí). □ Inserta la peso (J) en el sujetador (I) deslizándola en el sujetador (I). Weight here J I Weight here H instalar el dispensador 13 Cómo de jabón □ □ O Inserta el ensamblaje para jabón (P) en el orificio seleccionado del fregadero. Asegura el ensamblaje para jabón en el fregadero con la tuerca de montaje incluida (Q) para el dispensador de jabón.
Instalación (continuación) 14 Cómo hacer las conexiones del suministro de agua NOTA: El tubo de entrada del agua caliente se identifica con una etiqueta. Evita enroscar los cables juntos o colocarlos cerca y evita dañarlos. □ Enrosca la tuerca (1) de la línea de suministro en la salida de la válvula de suministro de agua (2) y aprieta con una llave. No aprietes demasiado. 1 2 H C Funcionamiento 1 Cómo purgar las tuberías y comprobar que no haya fugas 01 min.
Funcionamiento (continuación) poner en funcionamiento 2 Cómo el sensor 0 3 min. 45 15 NOTA: Es sensor se activa únicamente cuando la manija está en la posición abierta (ON). □ 30 Gira la manija (1) alejándola del grifo hasta dejarlo completamente abierto. Abre el suministro de agua activando el sensor (2) al pasar la mano a menos de 20.3 cm de este. □ Al tirar del maneral hacia uno mismo, el agua se tornará fría. Al tirar del maneral alejándolo de uno mismo, el agua se tornará caliente.
Solución de problemas suministro de agua no se La luz del sensor parpadea 1 Eldetendrá al mover la manija a 2 constantemente la posición cerrada (OFF). □ □ Cuando giras la manija a la posición abierta, se abre el flujo de agua. Si la manija está cerrada, muévela a la posición abierta y mueve la mano en el área del sensor. Si el sensor parpadea 10 veces de forma lenta y constante, reemplaza las 4 baterías “AA”.
Solución de problemas (continuación) caudal de agua es bajo o el 4 Elindicador LED del cabezal no activa el flujo 3 Eldesensor agua □ Cuando giras la manija a la posición abierta, se abre el flujo de agua. □ Sin embargo, cuando mueves la mano frente al sensor, el flujo no agua no se cierra como debería ser. rociador no funciona □ Esto podría indicar que la arandela del extremo que dice “adentro” (“in”) de la caja de control está sucia o dañada. Quita la manguera y desatornilla el conector.
Piezas de repuesto 23 2 3 1 24 4 19 5 6 7 20 8 15 21 22 16 17 11 18 12 Descripción 25 9 13 14 Las etiquetas de identificación de la mezcladora pueden encontrarse en la entrada de agua caliente.
¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM/GLACIERBAY Conserva este manual para uso futuro.