Internet# 206777953 206777955 Model# 67579W-6301 67579W-6335 SKU# 1001754322 1001754324 INSTALLATION AND CARE GUIDE TWO-HANDLE LAVATORY FAUCET Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this lavatory faucet.
Table of Contents Important Information ..............................2 Warranty ...................................................2 Pre-Installation .........................................2 Planning Installation ..............................2 Tools and Hardware Required ...............2 Package Contents ..................................3 Installation ................................................4 Operation...................................................8 Care and Cleaning ......................
Pre-Installation (continued) PACKAGE CONTENTS Faucet Assembly ClickInstall Drain Assembly M D* K A E* L F* G* B J I C H* NOTE: *Items D - H come pre-assembled. Part Description Quantity Part Description Quantity Drain body 1 A Faucet 1 H B Gasket 1 I Joint 1 C Mounting nut 2 J Horizontal rod 1 D Pop up stopper 1 K Lift rod strap 1 E Pop-up flange 1 L Clip 1 F Rubber washer 1 M Lift rod 1 G Lock nut 1 3 HOMEDEPOT.
Installation 1 Installing the faucet assembly 2 Preparing the pop-up assembly □ CAUTION: Always shut off the water supply before removing an existing faucet or replacing any part of a faucet. Open the faucet handle to relieve water pressure and ensure that the water is completely shut off. □ Shut off the water supply. Remove the old faucet. □ Clean the mounting surface. □ Ensure the gasket (B) is on the bottom of the new faucet (A). □ Place the faucet (A) through the mounting holes in the sink.
Installation (continued) 3 Installing the drain body the stopper and 4 Installing horizontal rod □ Apply silicone sealant (not included) under the drain flange (E) and place the drain flange (E) into the drain hole of the sink. □ From underneath the sink, screw the drain body (H) onto the drain flange (E). Ensure that the opening (1) for the ball rod on the drain body (H) faces towards the rear of the sink. □ Tighten the rubber washer (F) and lock nut (G) on the drain body (H). Hand-tighten only.
Installation (continued) 5 Installing the lift rod □ Slide the lift rod (M) down into the lift rod strap (K) through the faucet (A) until it clicks into the lift rod strap (K). NOTE: If a shorter lift rod (M) is required for your installation, you may call Glacier Bay Customer Service for assistance. M M 2 M K K 1 A 6 Attaching the horizontal rod and strap □ Press the horizontal rod (J) down to ensure the stopper (D) is in the maximum open position.
Installation (continued) 7 Adjusting the length of lift rod strap (optional) □ If the pop up lift rod strap (K) is interfering with your installation, as shown in Fig. 1, the lift rod strap (K) can be cut shorter. □ Once you have identified the proper hole in the lift rod strap (K) that is necessary for your installation, you may cut off the bottom portion (1) of the lift rod strap (K) by snapping it off with pliers or cutting it off with a saw at the cutting point (2), as shown in Fig. 2.
Installation (continued) the water supply 9 Making connections □ □ Use 1/2 in. I.P.S. faucet connections (2), or use supply line coupling nuts (3) (not included) with a 3/8 in. O.D. ball-nose riser (1). Use wrenches to tighten the connections. Do not overtighten. 1 3 2 Operation 1 Flushing and checking for leaks A IMPORTANT: After installation is complete, remove the aerator from the faucet (A) with a coin (1) to flush the water lines.
Care and Cleaning □ To clean, wipe down with a damp cloth and dry with a towel. □ Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will be voided. Troubleshooting NOTE: Refer to the service parts section in this manual for a detailed drawing showing the location of the parts listed below. Problem Possible Cause There are leaks from the handle. The bonnet nut has come loose and/or the washer is dirty or damaged. □ Tighten the bonnet nut.
Service Parts 10 1 2 3 4 Faucet ID tags can be found by removing the hot water handle 5 6 7 9 8 Part Description Part Number 1 Handle assembly RP13481* 2 Bonnet nut RP70435 3 Washer RP64123 4 Cartridge H RP20067 5 Cartridge C RP20068 6 Aerator RP30187 7 Gasket RP70504 8 Mounting nut RP56001 9 ClickInstall™ drain assembly RP40228* 10 Lift rod RP40239* *Specify Finish Many replacement cartridges, aerators, and drain assemblies can be purchased at your local The Home Depo
Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Retain this manual for future use.
Internet núm. 206777953 206777955 Modelo núm. 67579W-6301 67579W-6335 SKU núm. 1001754322 1001754324 GUÍA DE USO Y MANTENIMIENTO GRIFO PARA LAVAMANOS, DE DOS LLAVES ¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Tabla de contenido Información importante .........................13 Garantía...................................................13 Pre-instalación .......................................13 Planificación de la instalación .............13 Herramientas y herrajes necesarios ....13 Contenido del paquete .........................14 Instalación ..............................................15 Funcionamiento ......................................19 Cuidado y limpieza ................................
Pre-instalación (continuación) CONTENIDO DEL PAQUETE Ensamblaje de la mezcladora Ensamblaje de desagüe ClickInstall M D* K A E* L F* G* B J I C H* NOTA: *Los artículos D - H vienen preensamblados.
Instalación instalar el ensamblaje preparar el ensamblaje 1 Cómo 2 Cómo del grifo emergente □ PRECAUCIÓN: Cierra siempre el suministro de agua antes de retirar un grifo existente o reemplazar alguna parte del mismo. Abre la llave del grifo para liberar la presión de agua y asegúrate de que el suministro de agua esté completamente cerrado. □ Cierra el suministro de agua. Retira el grifo anterior. □ Limpia la superficie de montaje.
Instalación (continuación) instalar el cuerpo del instalar el tapón y la 3 Cómo 4 Cómo drenaje varilla horizontal □ Aplica sellador de silicona (no incluido) debajo de la brida del drenaje (E) y coloca ésta dentro del orificio de drenaje del lavabo. □ Desde la parte inferior del lavabo, enrosca el cuerpo del drenaje (H) en la brida del drenaje (E). Asegúrate de que la abertura (1) para la varilla de bola del cuerpo del drenaje (H) esté frente a la parte posterior del lavabo.
Instalación (continuación) 5 Cómo instalar la varilla de elevación □ Desliza la varilla de elevación (M) hacia abajo en la correa de la varilla (K) y a través del grifo (A) hasta que haga clic dentro de la correa (K). NOTA: Si necesitas una varilla de elevación (M) más corta para tu instalación, puedes llamar al Servicio al Cliente de Glacier Bay para recibir ayuda.
Instalación (continuación) 7 Cómo ajustar el largo de la correa de la varilla de elevación (opcional) □ Si la presilla de la varilla de elevación (K) interfiere con tu instalación, como se muestra en la Fig. 1, la presilla de la varilla de elevación (K) puede recortarse.
Instalación (continuación) hacer las conexiones 9 Cómo del suministro de agua □ Usa conexiones de grifos de 1/2" IPS (2) o tuercas de acoplamiento de líneas de suministro (3) (no incluidas) con un tubo montante de bola de diámetro exterior de 3/8" (1). □ Usa llaves para apretar las conexiones. No aprietes demasiado.
Cuidado y limpieza □ Para limpiar, usa un paño húmedo y seca con una toalla. □ No uses limpiadores abrasivos, esponjas de alambre o productos químicos fuertes para limpiar esta mezcladora, pues ello anulará la garantía. Solución de problemas NOTA: Consulta la sección de piezas de repuesto de este manual para ver un dibujo detallado que muestra la ubicación de las piezas enumeradas a continuación. Problema Posible causa Solución Hay filtración por el maneral.
Piezas de repuesto 10 1 2 3 4 Las etiquetas de identificación de la mezcladora pueden verse al quitar el maneral del agua caliente.
¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Conserva este manual para uso futuro.
Internet nº 206777953 206777955 Modèle n° 67579W-6301 67579W-6335 UGS n° 1001754322 1001754324 GUIDE D’INSTALLATION ET D’ENTRETIEN ROBINET DE LAVABO À DEUX MANETTES Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelez le service à la clientèle Glacier Bay entre 8 h et 19 h, HNE, du lundi au vendredi au entre 9 h et 18 h, HNE, le samedi au 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Table des matières Information importante ..........................24 Garantie...................................................24 Pré-installation .......................................24 ................24 Outils et quincaillerie requis ................24 Contenu de l’emballage .......................25 Installation ..............................................26 Utilisation ................................................30 Entretien et nettoyage ............................31 Dépannage ............
Pré-installation (suite) CONTENU DE L'EMBALLAGE Robinet Évacuation ClickInstall M D* K A E* L F* G* B J I C H* REMARQUE : *Les articles D à H sont fournis pré-assemblés.
Installation de l'ensemble de de l'évacuation 1 Installation 2 Préparation robinetterie mécanique □ ATTENTION : Fermez l’alimentation en eau CAUTION: Always turn toujours off the water supply before avant de retirer un robinet ou d’en removing an existing faucetexistant or replacing anyremplacer part of a une pièce quelconque. Ouvrez la poignée du robinet pour libérer faucet.
Installation (suite) du corps 3 Installation d'évacuation □ de la bonde et de 4 Installation la tige horizontale Appliquez du mastic à la silicone (non compris) sous la bride d’évacuation (E) et placez la bride d’évacuation (E) dans le trou d’évacuation de l’évier. □ Avant l’installation, dévissez le capuchon de protection (1) de la tige horizontale (J). □ Enfoncez la bonde (D) dans le trou d’évacuation de l’évier.
Installation (suite) 5 Installation de la tige de levage □ Faites glisser la tige de levage (M) vers le bas dans la courroie de la tige de levage (K) à travers le robinet (A), jusqu’à ce qu’elle s’enclenche dans la courroie de la tige de levage (K). REMARQUE : Si une tige de levage (M) plus courte est requise pour votre installation, vous pouvez contacter le service à la clientèle de Glacier Bay pour une assistance.
Installation (suite) 7 Régler la longueur de la sangle de la tige de levage (facultatif) □ Si la sangle de la tige de levage de l’évacuation mécanique (K) gêne votre installation, comme illustré sur la Fig. 1, la sangle de la tige de levage (K) peut être raccourcie.
Installation (suite) des conduites 9 Raccordement d’alimentation en eau □ Utilisez des raccords de robinet IPS de 1,27 cm (½ po) (2), ou utilisez des écrous d'accouplement pour conduite d'alimentation (3) (non compris) avec une colonne montante à bout sphérique de D.E. 9,53 mm (3/8 po) (1). □ Utilisez la clé pour serrer les raccords. Ne serrez pas trop.
Entretien et nettoyage □ Pour nettoyer, essuyez avec un linge humide et séchez avec une serviette. □ N'utilisez pas de nettoyants abrasifs, de la laine d’acier ou de produits chimiques abrasifs pour nettoyer ce robinet, sinon la garantie sera annulée. Dépannage REMARQUE : Consultez la section pièces de rechange de ce guide pour une illustration détaillée de l’emplacement des pièces énumérées ci-dessous. Problème Cause possible Solution La manette fuit.
Pièces de rechange 10 1 2 3 4 Les étiquettes d’identité du robinet sont repérées en retirant la manette d’eau chaude.
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelez le service à la clientèle Glacier Bay entre 8 h et 19 h, HNE, du lundi au vendredi au entre 9 h et 18 h, HNE, le samedi au 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Conservez ce manuel pour référence future.