Installation Guide

ManualsBrandsGlacier Bay ManualsBathKeegan 18 in. Towel Bar in Oil Rubbed Bronze

Item #591-205

596-776

Model #BTB01100RW

BTB01200RW

USE AND CARE GUIDE

TOWEL BAR

TOOLS REQUIRED

Phillips

screwdriver

Electric drill Pencil

E-Z Ancor

x4 Mounting bracket x2 Mounting screw x4

Hex wrench x1 Set screw x2

Claw

hammer

HARDWARE INCLUDED

Determining the mounting

location

Installing the bracket in a

wood stud

Installing the bracket in

drywall

Determine the location where you wish to

install your accessory.

Align the mounting brackets with pilot

holes and secure with the mounting

screws.

Drill a 3/32 in. pilot hole at each pencil

mark made.

Align the mounting brackets with the E-Z

Ancor

and secure with the mounting

screws.

Place the mounting bracket at the desired

location and mark the installation holes

using a pencil.

Drill a 1/8 in. pilot hole at each pencil

mark made.

Drive the E-Z Ancor

into the wall using

a Phillips screwdriver until ush with

the wall.

Installation

NOTE: To install the bracket in a wood stud,

proceed to Step 3. To install the bracket in

ceramic tile, proceed to Step 4.

HOMEDEPOT.COM

Please contact 1-855-434-5224 for further assistance.

Summary of content (6 pages)

PAGE 1
Item #591-205 596-776 Model #BTB01100RW BTB01200RW USE AND CARE GUIDE TOWEL BAR TOOLS REQUIRED Phillips screwdriver HARDWARE INCLUDED Electric drill Pencil E-Z Ancor® x4 Mounting bracket x2 Hex wrench x1 Set screw x2 Mounting screw x4 Claw hammer Installation the mounting 1 Determining location Determine the location where you wish to install your accessory. Place the mounting bracket at the desired location and mark the installation holes using a pencil.
PAGE 2
Installation (continued) the bracket in 4 Installing ceramic tile the bathroom 5 Installing accessory Drill a 1/4 in. pilot hole at each pencil mark made. Tap 1/4 in. masonry wall anchors (not included) into the wall with a hammer until flush with the wall. Align the mounting bracket with installed masonry wall anchors (not included) and secure with the mounting screws. Slide each end of the bar into the two posts. Attach the towel bar to the mounting bracket using the set screws.
PAGE 3
Article n° 591-205 596-776 Modèle n° BTB01100RW BTB01200RW GUIDE D’UTILISATION ET D’ENTRETIEN PORTE-SERVIETTES OUTILS REQUIS MATÉRIEL INCLUS E-Z AncorMD x4 Clé hexagonale x1 Tournevis Phillips Perceuse électrique Crayon Support de montage x2 Vis de fixation x4 Vis de pression x2 Marteau à panne fendue Installation de l’emplacement de 1 Choix l’accessoire Déterminez l’emplacement où les accessoires seront installés.
PAGE 4
Installation (suite) de la plaque de 4 Installation montage sur des carreaux des accessoires de 5 Installation salle de bain de céramique Insérer chaque extrémité de la barre dans les deux embouts. Fixer le porte-serviette aux plaques de montage à l’aide des vis de pression. Serrer solidement avec une clé hexagonale. Percer un trou de guidage de 1/4 po (6,35 mm) à chaque endroit marqué au crayon.
PAGE 5
Núm. de artículo 591-205 596-776 Núm. de modelo BTB01100RW BTB01200RW GUÍA DE USO Y CUIDADO TOALLERO-BARRAL HERRAMIENTAS REQUERIDAS SE INCLUYE LOS HARRAJES E-Z Ancor® x4 Llave hexagonal x1 Destornillador Phillips Taladro elécrico Lápiz Soporte de montaje x2 Tornillo de montaje x4 Tornillo de presión x2 Martillo de orejas Instalación 1 Elección del lugar de montaje Elija el lugar donde desea instalar el accesorio.
PAGE 6
Instalación (continuación) de accesorios 4 Instalación para el cuarto de baño de accesorios 5 Instalación para el cuarto de baño Taladre un orificio guía de 1/4” en cada una de las marcas hechas con lápiz. Introduzca en la pared los sujetadores murales (no incluidos) con un martillo hasta que estén a nivel con la pared. Alinee el soporte de montaje con los sujetadores murales (no incluidos) y sujete el soporte con los tornillos de montaje. Introduzca cada extremo de la barra en las dos sujeciones.