Installation Guide

Installation (continued)
4
3
Installing the faucet assembly
Preparing the sink
D
6
Place the sink (A) into the installation hole to verify the fit. Adjust the cutout if necessary.
Install the strainer assembly as these steps describe. It is easier to install the strainer assembly to the sink before the sink is installed to
the cabinet.
Apply a small amount of plumbers putty (not included) in the notch around the drain hole of the sink (A) .
Place the strainer ring (3) on top of the drain hole in the sink (A).
Insert the screener (1) into the bowl (2) and place this assembly into the drain hole in the sink (A).
From underneath the sink (A), place the rubber washer (4), paper washer (5), locknut (6), plastic joint (7), and connecting nut (8) over
the drain hole in the sink (A).
Tighten the locknut (6) and connecting nut (8) to hold the strainer assembly securely in place.
Shut off the water supply.
Insert the faucet assembly (D) through the hole in the sink.
1
1
3
3
6
6
7
7
8
8
5
5
4
4
2
2
CAUTION: Always shut off the water supply before removing an existing faucet or
replacing any part of a faucet. Open the faucet handle to relieve water pressure and
ensure that the water is completely shut off.
Installation (continued)
4
3
Installing the faucet assembly
Preparing the sink
D
6
Place the sink (A) into the installation hole to verify the fit. Adjust the cutout if necessary.
Install the strainer assembly as these steps describe. It is easier to install the strainer assembly to the sink before the sink is installed to
the cabinet.
Apply a small amount of plumbers putty (not included) in the notch around the drain hole of the sink (A) .
Place the strainer ring (3) on top of the drain hole in the sink (A).
Insert the screener (1) into the bowl (2) and place this assembly into the drain hole in the sink (A).
From underneath the sink (A), place the rubber washer (4), paper washer (5), locknut (6), plastic joint (7), and connecting nut (8) over
the drain hole in the sink (A).
Tighten the locknut (6) and connecting nut (8) to hold the strainer assembly securely in place.
Shut off the water supply.
Insert the faucet assembly (D) through the hole in the sink.
1
1
3
3
6
6
7
7
8
8
5
5
4
4
2
2
CAUTION: Always shut off the water supply before removing an existing faucet or
replacing any part of a faucet. Open the faucet handle to relieve water pressure and
ensure that the water is completely shut off.
Installation (continued)
6
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
CAUTION: Always shut off the water supply before removing and existing faucet or
replacing any part of a faucet. Open the faucet handle to relieve water pressure and
ensure that the water is completely shut off.
4
Installing the faucet assembly
3
Preparing the sink
Place the sink (A) into the installation hole to verify the fit. Adjust the cutout if necessary.
Install the strainer assembly as these steps describe. It is easier to install the strainer assembly to the sink before the sink is installed to the
cabinet.
Apply a small amount of plumbers putty (not included) in the notch around the drain hole of the sink (A) .
Place the strainer ring (3) on top of the drain hole in the sink (A).
Insert the screener (1) into the bowl (2) and place this assembly into the drain hole in the sink (A).
From underneath the sink (A), place the rubber washer (4), paper washer (5), locknut (6), plastic joint (7), and connecting nut (8) over the
drain hole in the sink (A).
Tighten the locknut (6) and connecting nut (8) to hold the strainer assembly securely in place.
Shut off the water supply.
Insert the faucet assembly (D) through the hole in the sink.
Installation (continued)
4
3
Installing the faucet assembly
Preparing the sink
D
6
Place the sink (A) into the installation hole to verify the fit. Adjust the cutout if necessary.
Install the strainer assembly as these steps describe. It is easier to install the strainer assembly to the sink before the sink is installed to
the cabinet.
Apply a small amount of plumbers putty (not included) in the notch around the drain hole of the sink (A) .
Place the strainer ring (3) on top of the drain hole in the sink (A).
Insert the screener (1) into the bowl (2) and place this assembly into the drain hole in the sink (A).
From underneath the sink (A), place the rubber washer (4), paper washer (5), locknut (6), plastic joint (7), and connecting nut (8) over
the drain hole in the sink (A).
Tighten the locknut (6) and connecting nut (8) to hold the strainer assembly securely in place.
Shut off the water supply.
Insert the faucet assembly (D) through the hole in the sink.
1
1
3
3
6
6
7
7
8
8
5
5
4
4
2
2
CAUTION: Always shut off the water supply before removing an existing faucet or
replacing any part of a faucet. Open the faucet handle to relieve water pressure and
ensure that the water is completely shut off.
Installation (continued)
4
3
Installing the faucet assembly
Preparing the sink
D
6
Place the sink (A) into the installation hole to verify the fit. Adjust the cutout if necessary.
Install the strainer assembly as these steps describe. It is easier to install the strainer assembly to the sink before the sink is installed to
the cabinet.
Apply a small amount of plumbers putty (not included) in the notch around the drain hole of the sink (A) .
Place the strainer ring (3) on top of the drain hole in the sink (A).
Insert the screener (1) into the bowl (2) and place this assembly into the drain hole in the sink (A).
From underneath the sink (A), place the rubber washer (4), paper washer (5), locknut (6), plastic joint (7), and connecting nut (8) over
the drain hole in the sink (A).
Tighten the locknut (6) and connecting nut (8) to hold the strainer assembly securely in place.
Shut off the water supply.
Insert the faucet assembly (D) through the hole in the sink.
1
1
3
3
6
6
7
7
8
8
5
5
4
4
2
2
CAUTION: Always shut off the water supply before removing an existing faucet or
replacing any part of a faucet. Open the faucet handle to relieve water pressure and
ensure that the water is completely shut off.
Installation (continued)
6
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
CAUTION: Always shut off the water supply before removing and existing faucet or
replacing any part of a faucet. Open the faucet handle to relieve water pressure and
ensure that the water is completely shut off.
4
Installing the faucet assembly
3
Preparing the sink
Place the sink (A) into the installation hole to verify the fit. Adjust the cutout if necessary.
Install the strainer assembly as these steps describe. It is easier to install the strainer assembly to the sink before the sink is installed to the
cabinet.
Apply a small amount of plumbers putty (not included) in the notch around the drain hole of the sink (A) .
Place the strainer ring (3) on top of the drain hole in the sink (A).
Insert the screener (1) into the bowl (2) and place this assembly into the drain hole in the sink (A).
From underneath the sink (A), place the rubber washer (4), paper washer (5), locknut (6), plastic joint (7), and connecting nut (8) over the
drain hole in the sink (A).
Tighten the locknut (6) and connecting nut (8) to hold the strainer assembly securely in place.
Shut off the water supply.
Insert the faucet assembly (D) through the hole in the sink.
6
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con el 1-855-HD-GLACIER para obtener más ayuda.
PRECAUCIÓN: Cierre siempre el suministro de agua antes de quitar un grifo
existente o reemplazar cualquier parte de un grifo. Abra el grifo para aliviar la presión
del agua y asegúrese de que el suministro de agua está completamente cerrado.
4
Instalación del conjunto del grifo
3
Preparación del fregadero
Colocar el fregadero (A) en el orificio de instalación para comprobar el ajuste. Ajustar la línea de corte si es necesario.
Instalar el conjunto de drenaje como se describe en estos pasos. Es más fácil instalar el conjunto de drenaje antes de instalar el fregadero
Aplicar una pequeña cantidad de masilla para plomería (no incluida) en la muesca alrededor del orificio de drenaje del fregadero (A).
Colocar el anillo de drenaje (3) encima del orificio de drenaje en el fregadero (A).
Insertar la rejilla (1) en la cuba (2) y colocar este conjunto en el orificio de drenaje en el fregadero (A).
Desde abajo del fregadero (A), colocar la arandela de caucho (4), arandela de papel (5), contratuerca (6), junta plástica (7) y la tuerca
Apretar la contratuerca (6) y la tuerca de conexión (8) para mantener el conjunto de drenaje firmemente en su lugar.
Desconectar el suministro de agua.
Insertar el cuerpo del grifo (D) a través del orificio en el fregadero.
Instalación por arriba (continuación)