Installation Guide

8
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con el 1-855-HD-GLACIER para obtener más ayuda.
NOTA: El conducto lateral de entrada del
agua caliente está marcado con una etiqueta.
uno del otro y dañarlos.
7
Colocación del conector rápido
9
Conexión del suministro de agua
8
Instalación del peso
Empujar el conector rápido (18) firmemente hacia arriba
moderadamente para asegurarse de que la conexión
Installation (continued)
8
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
NOTE: The hot side inlet tube is indicated by
a label. Avoid twisting wires together or placing
the wires close to each other and damaging.
7
Attaching the quick connector to
the receiving block
9
Making the water supply
connections
8
Installing the weight
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Install the weight clip (20) at the point of the hose marking
“weight here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Weight
here
W
eight
he
re
Enroscar la tuerca (1) de la línea de alimentación en la
salida de la válvula de suministro de agua (2) y apretarla
Installation (continued)
8
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
NOTE: The hot side inlet tube is indicated by
a label. Avoid twisting wires together or placing
the wires close to each other and damaging.
7
Attaching the quick connector to
the receiving block
9
Making the water supply
connections
8
Installing the weight
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Install the weight clip (20) at the point of the hose marking
“weight here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Weight
here
Weight
her
e
Instalar la presilla del peso (20) en el punto de la manguera
Insertar el peso (19) en la presilla (20) deslizándolo
Installation (continued)
8
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
NOTE: The hot side inlet tube is indicated by
a label. Avoid twisting wires together or placing
the wires close to each other and damaging.
7
Attaching the quick connector to
the receiving block
9
Making the water supply
connections
8
Installing the weight
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Install the weight clip (20) at the point of the hose marking
“weight here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Attaching the quick connector
to the receiving block
7 8
9
8
Installation (continued)
9
18
Weight
here
Weight
here
20
20
19
19
2
1
Installing the weight
Install the weight clip (20) at the point of the hose marking "weight
here”.
Insert the weight (19) onto the clip (20) by sliding it down onto the
clip (20).
Push the quick connector (18) firmly upward and attach it to
the receiving block (9). Pull down moderately to ensure the
connection has been made.
Making the water supply
connections
Thread the nut (1) on the supply line onto the outlet of
the water supply valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
Weight
here
W
eight
he
r
e
Peso
aquí
Peso
aquí
Instalación por arriba (continuación)