Installation Guide
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Installation (continued)
9
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
IMPORTANT: After installation is completed, turn
on the hot and cold water supplies. Check for leaks.
10
Flushing and checking for leaks
11
Removing the quick connector
12
Installing the accessories
Pull the hose assembly out of the spout and remove the
spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then pull
down to disconnect.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the
sink.
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Squeeze
Pull
down
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Installation (continued)
9
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
IMPORTANT: After installation is completed, turn
on the hot and cold water supplies. Check for leaks.
10
Flushing and checking for leaks
11
Removing the quick connector
12
Installing the accessories
Pull the hose assembly out of the spout and remove the
spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then pull
down to disconnect.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the
sink.
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Squeeze
Pull
down
9
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con el 1-855-HD-GLACIER para obtener más ayuda.
IMPORTANTE: Una vez finalizada la instalación,
conecte los suministros de agua caliente y fría.
Compruebe si hay fugas.
10
Drenaje y verificación de fugas
11
Extracción del conector rápido
12
Montaje de los accesorios
Sacar el conjunto de la manguera de la boquilla y extraer
el cabezal de rociado desenroscándolo de la manguera
en sentido contrario de las agujas del reloj. Asegúrese de
mantener el extremo de la manguera hacia abajo dentro
del fregadero y girar el grifo a la posición “tibia” donde
se mezcla el agua caliente y fría.
Deje que el agua corra por las líneas durante un minuto.
Esto elimina cualquier residuo que pueda dañar las
partes internas.
Vuelva a apretar las conexiones si es necesario, pero
rociado a mano ajustándolo en la manguera de rociado
en sentido de las agujas del reloj.
Si es necesario extraer el conector rápido (1), apriete las
pestañas (2) del conector rápido y luego jale hacia abajo
para desconectarlo.
Cuando termine, coloque la rejilla del fregadero (H), la tabla
de cortar (E), la cesta (F), la rejilla móvil (G) y la cubierta
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Installation (continued)
9
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
IMPORTANT: After installation is completed, turn
on the hot and cold water supplies. Check for leaks.
10
Flushing and checking for leaks
11
Removing the quick connector
12
Installing the accessories
Pull the hose assembly out of the spout and remove the
spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes away
any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then pull
down to disconnect.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the
sink.
Flushing and checking for leaks
11
9
Installation (continued)
10
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze
the tabs (2) on the quick connector and then pull down to
disconnect.
Squeeze
Pull
down
1
1
2
12
Installing the accessories
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to the
warm position where it mixes hot and cold water.
Flush the water lines for one minute. This flushes
away any debris that could cause damage to internal
Re-tighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening
it back onto the spray hose in a clockwise direction.
When finished, place the sink grid (H), cutting board (E),
basket (F), rolling grid (G) and strainer cover (I) into the sink.
D
I
E
F
H
G
IMPORTANT: After installation is completed, turn on
the hot and cold water supplies. Check for leaks.
Squeeze
Pull
down
Apretar
Bajar
Instalación por arriba (continuación)