Installation Guide

1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
Installation type 2: Undermount
10
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown here.
Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a professional
installer install this sink for the undermount style.
1
Preparing the countertop
2
Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
Installation type 2: Undermount
10
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown here.
Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a professional
installer install this sink for the undermount style.
1
Preparing the countertop
2
Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
1
2
Preparing the countertop Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown
here. Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a
professional installer install this sink for the undermount style.
10
Installation type 2: Undermount
10
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
WARNING: When you choose undermount style installation, do not pull out the installation rail shown here.
Pulling this rail out will permanently damage the sink. It is strongly recommended that you have a professional
installer install this sink for the undermount style.
1
Preparing the countertop
2
Cutting the installation hole
Check the template (A) and select the cutline you want: line A1
is bowl size; line A2 is 1/2 wider than bowl size. If you choose
line A1 or A2, tear off the template through the broken line.
Place the template (A1 or A2) on the countertop. Ensure the
template is centered on the counter so that it is parallel to the
counter edge and that the installation hole will not interfere
with the structure of the cabinet. Tape the template (A1 or A2)
to the countertop to keep it in place and then trace the cutout
line on the template (A1 or A2) with a pencil.
Drill a pilot hole and cut the countertop opening. Use the
appropriate cutting tool for the surface you are cutting.
10
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con el 1-855-HD-GLACIER para obtener más ayuda.
ADVERTENCIA: Cuando escoja la instalación por abajo, no desprenda el riel de instalación que se
muestran en esta ilustración. Desprender este riel dañará permanentemente el fregadero. Se recomienda
1
Preparación de la encimera
2
Corte del orificio de instalación
Revisar la plantilla (A) y seleccionar la línea de corte deseada:
la línea A1 es del tamaño de la cuba; la línea A2 es 1/2 pulgada
más ancha que el tamaño de la cuba. Si elige la línea A1 o A2,
rasgue la plantilla por la línea de división. Coloque la plantilla
(A1 o A2) sobre la encimera. Asegúrese de que la plantilla esté
centrada en la encimera de modo que quede paralela a su
borde y de que el orificio de instalación no interfiera con la
estructura del armario. Pegue con cinta adhesiva la plantilla
(A1 o A2) en la encimera para mantenerla en su lugar y trazar
la línea de corte en la plantilla (A1 o A2) con un lápiz.
Taladrar un agujero de prueba y cortar la abertura de la
encimera. Use la herramienta de corte adecuada para
Clips de montaje inferior no incluidos. Si está instalando este fregadero como
debajo de la superficie, comuníquese con un instalador profesional o contáctenos
al 1-855-HD-GLACIER para determinar el tipo de clip necesario.
NOTA:
Instalación por abajo