Installation Guide

6
Installing the sink
Apply a bead of silicone around the perimeter of the top of the sink.
Position and align the hollow beneath the sink countertop.
Once the sink is in the correct position, install the mounting clips. Tighten the mounting clip until the sink rim is aligned to the countertop.
Check the alignment while squeezing, so that the front of the sink (A) is parallel to the countertop. Adjust and retighten if necessary. Do not
overtighten.
Clean the excess sealant with a rag.
7
Installing the faucet
8
Installing the accessories
Refer to steps 4 through 11 on pages 6 to 9.
D
I
E
F
H
G
When finished, place the sink grid (H), cutting board (E), basket (F),
rolling grid (G) and strainer cover (I) into the sink.
12
Installation Type 2 (continued)
12
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
6
Installing the sink
7
Installing the faucet
8
Installing the accessories
Apply a bead of silicone around the perimeter of the top of the sink.
Position and align the hollow beneath the sink countertop.
Once the sink is in the correct position, install the mounting clips. Tighten the mounting clip until the sink rim is aligned to the countertop.
Check the alignment while squeezing, so that the front of the sink (A) is parallel to the countertop. Adjust and retighten if necessary. Do not
overtighten.
Clean the excess sealant with a rag.
Refer to steps 4 through 11 on pages 6 to 9.
When finished, place the sink grid (H), cutting board (E), basket (F),
rolling grid (G) and strainer cover (I) into the sink.
6
Installing the sink
Apply a bead of silicone around the perimeter of the top of the sink.
Position and align the hollow beneath the sink countertop.
Once the sink is in the correct position, install the mounting clips. Tighten the mounting clip until the sink rim is aligned to the countertop.
Check the alignment while squeezing, so that the front of the sink (A) is parallel to the countertop. Adjust and retighten if necessary. Do not
overtighten.
Clean the excess sealant with a rag.
7
Installing the faucet
8
Installing the accessories
Refer to steps 4 through 11 on pages 6 to 9.
D
I
E
F
H
G
When finished, place the sink grid (H), cutting board (E), basket (F),
rolling grid (G) and strainer cover (I) into the sink.
12
Countertop
Hole inserto
Inserto
Clip
Screw
Mounting Diagram:
Silicone
sealant
Sink
12
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con el 1-855-HD-GLACIER para obtener más ayuda.
6
Instalación del fregadero
7
Instalación del grifo
8
Montaje de los accesorios
Aplicar un cordón de silicona alrededor del perímetro de la parte superior del fregadero.
Situar y alinear el hueco debajo de la encimera del fregadero.
Una vez que el fregadero esté en la posición correcta, instalar las presillas de montaje. Apretar la presilla de montaje hasta que el borde
Compruebe la alineación mientras lo aprieta, de modo que la parte frontal del fregadero (A) quede paralela a la encimera. Ajustar y volver
Limpiar el exceso de silicona con un trapo.
Consulte los pasos del 4 al 11 en las páginas 6 a 9.
Cuando termine, coloque la rejilla del fregadero (H), la tabla de
cortar (E), la cesta (F), la rejilla móvil (G) y la cubierta del drenaje (I)
en el fregadero.
6
Installing the sink
Apply a bead of silicone around the perimeter of the top of the sink.
Position and align the hollow beneath the sink countertop.
Once the sink is in the correct position, install the mounting clips. Tighten the mounting clip until the sink rim is aligned to the countertop.
Check the alignment while squeezing, so that the front of the sink (A) is parallel to the countertop. Adjust and retighten if necessary. Do not
overtighten.
Clean the excess sealant with a rag.
7
Installing the faucet
8
Installing the accessories
Refer to steps 4 through 11 on pages 6 to 9.
D
I
E
F
H
G
When finished, place the sink grid (H), cutting board (E), basket (F),
rolling grid (G) and strainer cover (I) into the sink.
12
Installation Type 2 (continued)
12
HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER fro further assistance.
6
Installing the sink
7
Installing the faucet
8
Installing the accessories
Apply a bead of silicone around the perimeter of the top of the sink.
Position and align the hollow beneath the sink countertop.
Once the sink is in the correct position, install the mounting clips. Tighten the mounting clip until the sink rim is aligned to the countertop.
Check the alignment while squeezing, so that the front of the sink (A) is parallel to the countertop. Adjust and retighten if necessary. Do not
overtighten.
Clean the excess sealant with a rag.
Refer to steps 4 through 11 on pages 6 to 9.
When finished, place the sink grid (H), cutting board (E), basket (F),
rolling grid (G) and strainer cover (I) into the sink.
6
Installing the sink
Apply a bead of silicone around the perimeter of the top of the sink.
Position and align the hollow beneath the sink countertop.
Once the sink is in the correct position, install the mounting clips. Tighten the mounting clip until the sink rim is aligned to the countertop.
Check the alignment while squeezing, so that the front of the sink (A) is parallel to the countertop. Adjust and retighten if necessary. Do not
overtighten.
Clean the excess sealant with a rag.
7
Installing the faucet
8
Installing the accessories
Refer to steps 4 through 11 on pages 6 to 9.
D
I
E
F
H
G
Instalación por abajo (continuación)