Installation Guide

1
2
9
Colocación del conector rápido
Empujar el conector rápido (N) firmemente hacia arriba
y fijarlo en el bloque receptor (1). Tirar hacia abajo
moderadamente para asegurarse de que la conexión
Sink
Sink
Push
up
Screw
Fig 1
7
Installing the weight
Insert the weight (O) onto the clip (P) by sliding
it down onto the clip (P).
Install the weight clip (P) at the point of the
hose marking “weight here”.
6
Attaching the quick connector
to the receiving block
Push the quick connector (N) firmly upward and
attach it to the receiving block (1). Pull down
moderately to ensure the connection has been
made.
1
Weight
here
Weight
h
e
re
10
Instalación del peso
Instalar el clip de peso (P) en el punto de la manguera
Insertar el peso (O) en la presilla (P) deslizándolo sobre
Sink
Sink
Push
up
Screw
Fig 1
7
Installing the weight
Insert the weight (O) onto the clip (P) by sliding
it down onto the clip (P).
Install the weight clip (P) at the point of the
hose marking “weight here”.
6
Attaching the quick connector
to the receiving block
Push the quick connector (N) firmly upward and
attach it to the receiving block (1). Pull down
moderately to ensure the connection has been
made.
1
Weight
here
Weight
h
e
re
Weight
here
Weight
here
11
Instalación del dispensador de jabón
Insertar el conjunto del dispensador de jabón (O) a través
Por debajo del fregadero, atornillar el dispensador de jabón (T)
al vástago del conjunto del dispensador de jabón (O). Insertar el
dispensador de jabón (Q) en el conjunto del dispensador de jabón (O).
8
Installing the soap dispenser
From under the sink, screw the soap dispenser (T) onto the
soap assembly (O) shank. Insert the soap pump (Q) down
into the soap assembly (O).
Insert the soap assembly (O) through the selected hole
in the sink. Secure the soap assembly(O) to the sink with
9
Making the water supply connections
Thread the nut (1) on the supply line onto the outlet of the
water supply valve (2) and tighten with a wrench. Do not
overtighten.
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
Q
O
S
T
Flushing and checking for leaks
Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose in a
counterclockwise direction. Be sure to hold the end of
the hose down into the sink and turn the faucet to
the warm position where it mixes hot and cold water.
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
11
Removing the quick connector
If it is necessary to remove the quick connector (1),
squeeze the tabs (2) on the quick connector and then
pull down to disconnect.
Topmount Installation (continued)
12
Conexión del suministro de agua
NOTA: El conducto lateral de entrada del agua caliente está
marcado con una etiqueta. Evite enrollar los cables juntos,
colocarlos cerca uno del otro y dañarlos.
Enroscar la tuerca (1) de la línea de alimentación en la
salida de la válvula de suministro de agua (2) y apretarla
con una llave. No apriete demasiado.
HOMEDEPOT.COM/GLACIERBAY
Póngase en contacto con 1-855-HDGLACIER para obtener más asistencia.
14
Instalación por abajo (continuación)