Installation Guide

ManualsBrandsGlacier Bay ManualsBath30 in. Vanity in Golden Pecan with AB Engineered Composite Vanity Top in White

DETERMINE WHERE TO PLACE THE VANITY

CARE & MAINTENANCE:

Cleaning Instructions: To clean surface of doors or cabinet, use non-abrasive cleansers only.

HINGE / DOOR ADJUSTMENT

Drawer Box

Decorative Hardware

Alignment Screws

Drawer Front

Alignment System

Screws

INSTALLATION INSTRUCTIONS

BATHROOM CABINETS

Top Back Rail

DRAWER FRONT ADJUSTMENT

1. Determine where the vanity will be located. Fasten the vanity to the wall with appropriate

wood screws (not provided) into wall studs or solid lumber through the back rail,

or use toogle bolts if necessary.

2. The drawer knobs are turned inside out to avoid damage in transit. Knobs must be

reattached on the outside of the cabinet to be functional.

3. Door pulls are normally stapled to the top back rail (inside a plastic bag).

4. Use the adjustment chart below to align your cabinet fronts.

NOTE: Decorative hardware and alignment system screws are located inside the drawer box.

1. Remove decorative hardware from the drawer front.

2. Hold drawer front in place and slightly loosen both alignment screws.

3. Move the drawer front left, right, up or down to desired position for alignment.

4. While holding the drawer front in place, tighten the alignment screws securely.

5. Install the decorative hardware to the outside of the drawer front.

Adjust gaps between

doors

Adjust door left

or right

Adjust door height

2700 Camino de Verdad

Weslaco, TX 78596

1 (800) 235-7747

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS BATHROOM CABINETS 2700 Camino de Verdad Weslaco, TX 78596 1 (800) 235-7747 DETERMINE WHERE TO PLACE THE VANITY Top Back Rail 1. Determine where the vanity will be located. Fasten the vanity to the wall with appropriate wood screws (not provided) into wall studs or solid lumber through the back rail, or use toogle bolts if necessary. 2. The drawer knobs are turned inside out to avoid damage in transit. Knobs must be reattached on the outside of the cabinet to be functional. 3.
PAGE 2
O SI LIC 1. Make sure the base of the vanity is leveled. N E HOW TO INSTALL VANITY TOP TO VANITY 2. Set the vanity top on top of the vanity base, checking the location of the p-trap and drain. 3 Remove the top and install the faucet per manufacturer’s installation instructions. 4. Tighten the pop-up drain with a wrench. Be careful not to over-tighten the pop-up drain. Over tightening may cause cracks on the marble top. 5. Attach water lines to faucet and connect the p-trap and drain. 6.
PAGE 3
INSTRUCCIONES DE INSTALACION DEL GABINETE DE BAÑO 2700 Camino de Verdad Weslaco, TX 78596 1 (800) 235-7747 DETERMINE EL AREA EN DONDE VA A COLOCAR EL GABINETE Soporte trasero superior 1. Determine en donde va a estar colocado el gabinete. Fije el gabinete a los barrotes de la estructura de la pared o a una área firme de madera con tornillos para madera apropiados (tornillos de 3” deberán ser suficientes, no incluidos) a través del soporte trasero del gabinete. Use taquetes si es necesario. 2.
PAGE 4
O SI LIC 1. Asegúrese que la base del gabinete esté nivelada colocando un nivel de burbuja diagonalmente sobre la parte superior del gabinete. N CÓMO SUJETAR EL LAVABO AL GABINETE DE BAÑO 2. Coloque el lavabo sobre la base del gabinete verificando la ubicación correcta de la trampa y el drenaje. 3. Remueva el lavabo e instale las llaves de acuerdo con las instrucciones de instalación del fabricante. 4. Ajuste manualmente el tubo del drenaje, luego gire ¼ de vuelta con una llave apropiada.