Internet# 300687594 300687627 304367453 Model# 461-3001 461-3004 HD461-3027H2 SKU# 1002213159 1002193890 1003015404 INSTALLATION AND CARE GUIDE TWO-HANDLE ROMAN TUB FAUCET Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Table of Contents Important Information ..............................2 Warranty ...................................................2 Pre-Installation .........................................2 Planning Installation ..............................2 Tools and Hardware Required ...............2 Package Contents ..................................3 Installation ................................................4 Operation...................................................7 Care and Cleaning ......................
Pre-Installation (continued) PACKAGE CONTENTS A C B H S I J T K L D E F M N O P Q G R Part Quantity Part A Description Spout assembly 1 K Description B Set screw 1 L Flange 2 C 3.2mm hex wrench 1 M Hot end valve 1 D Middle body 1 N Cold end valve 1 Index Quantity 2 E Rubber washer 1 O Rubber washer 2 F Metal washer 1 P Metal washer 2 G Mounting nut 1 Q Mounting nut 2 H Handle 2 R Hose 2 I Set screw 2 S Protective cap 1 J 2.
Installation 1 Preparing for installation 2 Removing the mounting kits □ CAUTION: Always shut off the water supply before removing an existing faucet or replacing any part of a faucet. Open the faucet handle to relieve water pressure and ensure that the water is completely shut off. □ Shut off the water supply. Remove the old faucet. □ Clean the mounting surface. □ Drill holes in the finished deck as shown in the diagram below. Remove the protective cap (S).
Installation (continued) 4 Installing the spout assembly 5 Removing the mounting kits □ Install the spout assembly (A) onto the connector (T). Be sure the spout assembly (A) is resting firmly on the deck. □ Push down on spout assembly (A) and tighten set screw (B) with the Hex wrench (Hex: 3.2mm, C). □ Adjust the rubber washers (O), metal washers (P) and mounting nuts (Q) to the bottom of valve bodys (M & N).
Installation (continued) 7 Installing the handle □ □ 8 Connecting the hoses Place the handle (H) onto the inverter (1). Place the set screw (I) into handle (H) and tighten set screw (I) with the Hex wrench (Hex: 2.5mm, J). Insert the index (K). Place the other handle onto the left (hot) valve and install the same way. H I □ Connect the hoses (R) to the bottom of the hot and cold end valves (M & N), as shown.
Operation 1 Flushing and checking for leaks □ Ensure the faucet handles are in the off position, and turn on the water supply to check for leaks. If you discover any leaks, check your connections to ensure they are installed properly. □ Turn on the hot and cold handles to allow the water to run for at least one minute. This flushes away any debris that could cause damage to internal parts. □ Turn off the water. Care and Cleaning □ To clean, wipe down with a damp cloth and dry with a towel.
Service Parts 12 2 3 13 4 1 5 14 6 15 Faucet ID tags can be found by removing the hot water handle 7 16 8 17 9 18 10 11 19 Part Description Part Number Part Description Part Number 1 Handle assembly H RP13529* 11 Mounting nut RP56014 2 Handle assembly C RP13530* 12 Set screw RP50103 3 Flange RP80614* 13 O-ring RP60056 4 Connector RP70116 14 Connector RP70459 5 Inverter RP64044 15 O-ring RP60094 6 Bonnet nut RP70001 16 Rubber washer RP64035 7 Cartr
Questions, problems, missing parts? Before returning to the store, call Glacier Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Retain this manual for future use.
Internet núm. 300687594 300687627 304367453 Modelo núm. 461-3001 461-3004 HD461-3027H2 SKU núm. 1002213159 1002193890 1003015404 GUÍA DE USO Y MANTENIMIENTO GRIFO DE DOS LLAVES PARA BAÑERA ROMANA ¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Tabla de contenido Información importante .........................11 Garantía...................................................11 Pre-instalación .......................................11 Planificación de la instalación .............11 Herramientas y herrajes necesarios ....11 Contenido del paquete .........................12 Instalación ..............................................13 Funcionamiento ......................................16 Cuidado y limpieza ................................
Pre-instalación (continuación) CONTENIDO DEL PAQUETE A C B H S I J T K L D E F M N O P Q G R Pieza Descripción Cantidad Pieza Descripción Cantidad A Ensamblaje del caño 1 K Índice 2 B Tornillo de fijación 1 L Brida 2 C Llave hexagonal de 3.
Instalación prepararse para la 1 Cómo instalación 2 Cómo quitar los kits de montaje □ PRECAUCIÓN: Cierra siempre el suministro de agua antes de retirar un grifo existente o reemplazar alguna parte del mismo. Abre la llave del grifo para liberar la presión de agua y asegúrate de que el suministro de agua esté completamente cerrado. □ □ □ Cierra el suministro de agua. Retira el grifo anterior. Limpia la superficie de montaje.
Instalación (continuación) instalar el ensamblaje 5 Cómo quitar los kits de montaje 4 Cómo del caño □ Instala el ensamblaje del caño (A) en el conector (T). Asegúrate de que el ensamblaje del caño (A) descanse firmemente sobre la cubierta. □ Presiona hacia abajo el conjunto del caño (A) y aprieta el tornillo de fijación (B) con la llave hexagonal (Hex.: 3.2 mm, C).
Instalación (continuación) 7 Cómo instalar la llave 8 Cómo conectar la mangueras □ Coloca la llave (H) en el inversor (1). Coloca el tornillo de fijación (I) dentro de la llave (H) y apriétalo con la llave hexagonal (Hex.: 2.5 mm, J). Inserta el índice (K). □ Coloca la otra llave sobre la válvula izquierda (agua caliente) e instala de la misma manera. H I J □ Conecta las mangueras (R) a la parte inferior de las válvulas de extremo de agua caliente y fría (M & N) como se muestra.
Funcionamiento purgar las tuberías y 1 Cómo comprobar que no haya fugas □ Asegúrate de que las llaves del grifo estén cerradas y abre el suministro del agua para comprobar que no haya filtraciones. Si descubres alguna filtración, verifica tus conexiones para asegurarte de que estén instaladas adecuadamente. □ Abre los manerales del suministro de agua fría y caliente y deja que corran durante al menos un minuto cada una. Esto elimina cualquier desecho que pudiera dañar las piezas internas.
Piezas de repuesto 12 2 3 13 4 1 5 14 6 15 Las etiquetas de identificación de la mezcladora pueden verse al quitar el maneral del agua caliente.
¿Problemas, preguntas o piezas faltantes? Antes de regresar a la tienda, llama al servicio al cliente de Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los sábados entre 9 a.m. y 6 p.m.(hora estándar del Este) 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Conserva este manual para uso futuro.
Internet nº 300687594 300687627 304367453 Modèle n° 461-3001 461-3004 HD461-3027H2 UGS n° 1002213159 1002193890 1003015404 GUIDE D’INSTALLATION ET D’ENTRETIEN ROBINET DE BAIGNOIRE ROMAINE À DEUX MANETTES Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelez le service à la clientèle Glacier Bay entre 8 h et 19 h, HNE, du lundi au vendredi au entre 9 h et 18 h, HNE, le samedi au 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.
Table des matières Installation ..............................................22 Utilisation ................................................25 Entretien et nettoyage ............................25 Dépannage .............................................25 Pièces de rechange ................................26 Information importante ..........................20 Garantie...................................................20 Pré-installation .......................................20 ................
Pré-installation (suite) CONTENU DE L'EMBALLAGE A C B H S I J T K L D E F M N O P Q G R Pièce Quantité Pièce A Bec du robinet Description 1 K B Vis de pression 1 C Clé hexagonale de 3,2 mm 1 D Corps central 1 E Rondelle en caoutchouc 1 F Rondelle en métal 1 G Écrou de montage 1 H Manette 2 I Vis de pression 2 J Clé hexagonale de 2,5 mm 1 21 Description Quantité Indicateur 2 L Bride 2 M Robinet d'arrêt d'eau chaude 1 N Robinet d'arrêt d'eau froide 1
Installation en vue de 1 Préparation l'installation des trousses 2 Retrait d’assemblage □ ATTENTION : Fermez l’alimentation en eau CAUTION: Always turn toujours off the water supply before avant de retirer un robinet ou d’en removing an existing faucetexistant or replacing anyremplacer part of a une pièce quelconque. Ouvrez la poignée du robinet pour libérer faucet.
Installation (suite) des trousses 4 Installation du bec du robinet 5 Retrait d’assemblage □ Installez le bec (A) sur le raccord (T). Assurez-vous que le bec (A) repose fermement sur la plaque. □ Enfoncez le bec (A) et serrez la vis de pression (B) à l’aide de la clé hexagonale (Hex : 3,2 mm, C). □ Ajustez les rondelles en caoutchouc (O), les rondelles en métal (P) et les écrous de montage (Q) en bas des corps de robinet (M et N).
Installation (suite) 7 Installing the handle □ □ des tuyaux 8 Branchement flexibles Placez la manette (H) sur l’inverseur (1). Placez la vis de pression (I) dans la manette (H) et serrez la vis de pression (I) à l’aide de la clé hexagonale (Hex : 2,5 mm, J). Insérez le repère de température (K). Placez l’autre manette sur la tige gauche (eau chaude) du robinet et fixez de la même manière. H I J □ Branchez les tuyaux flexibles (R) aux bas des robinets chaud et froid (M et N) comme illustré.
Utilisation 1 Purge et recherche de fuites □ Assurez-vous que les manettes du robinet sont en position arrêt, puis ouvrez l’alimentation en eau pour rechercher les fuites. Si vous découvrez des fuites, vérifiez vos raccords pour vous assurer qu’ils sont installés correctement. □ Ouvrez les manettes d’eau chaude et froide pour laisser couler l’eau pendant au moins une minute. Cela chasse les débris éventuels qui pourraient endommager les pièces internes. □ Coupez l’alimentation en eau.
Pièces de rechange 12 2 3 13 1 14 15 Les étiquettes d’identité du robinet sont repérées en retirant la manette d’eau chaude.
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelez le service à la clientèle Glacier Bay entre 8 h et 19 h, HNE, du lundi au vendredi au entre 9 h et 18 h, HNE, le samedi au 1-855-HD-GLACIER (1-855-434-5224) HOMEDEPOT.COM Conservez ce manuel pour référence future.