Installation Guide

ManualsBrandsGlacier Bay ManualsBathKinghurst 30 in. W x 21 in. D x 33.5 in. H Bathroom Vanity Cabinet Only in Dark Cognac

HOMEDEPOT.COM/GLACIERBAY

Please contact 1-888-774-8062 for further assistance.

Installation

PREPARING FOR INSTALLATION

NOTE: Before installation, make

sure all parts are present. Compare

parts with the Hardware Included list.

If any part is missing or damaged, do

not attempt to install the product.

□ Determine the desired mounting location,

and mark the wall where the unit will be

installed.

NOTE: For secure installation, the

unit must be mounted to at least one

wall stud.

CUTTING THE OPENING FOR

PLUMBING FIXTURES

NOTE: This step applies to vanity

cabinets with full back panels only.

□ Locate and mark plumbing on the back panel.

□ Drill a pilot hole through the back panel.

□ Use a keyhole saw to cut an opening for the

plumbing fixtures.

POSITIONING THE

CABINET

□ Move the cabinet into

place, and use wood

shims to level the

cabinet against the wall.

Use and Care Guide

Vanity Combo

TOOLS REQUIRED

Claw hammer Safety goggles

Phillips

Screwdriver

Caulk/sealant

Power drill

Measuring tape Wall hardware Keyhole saw Level

HARDWARE INCLUDED

INSTALLING THE CABINET

□ For wall stud installation, insert #12 x 3 in. screws with

washers into the stud locations (not included).

□ For drywall installation, drill holes at the appropriate

locations and insert toggle bolts with washers (not included).

□ For concrete wall installation, drill 1/4 in. holes at the

appropriate locations and insert #12 wall anchors, followed

by #12 x 3 in. screws (not included).

INSTALLING THE HARDWARE

KHG30D

KHG36D

□ Attach the handles (AA) and the knobs (BB) to the door

the top drawer on the vanity with short screws (CC) and

to the two lower drawers on the vanity with long screws

(DD).

REMOVING THE DRAWER

Press

downward

Press

upward

□ Press release levers in opposite directions while pulling drawer out of the vanity.

AA - Handle

x 4

BB - Long

Screw

x 4

CC - Medium

Screw

x 2

DD - Short

Screw

x 2

Item # 1002 835 295

Item # 1002 835 317

Item # 1002 835 320

Item # 1002 835 323

Item # 1002 814 804

Item # 1002 814 817

Model # KHWHT30D

Model # KHWHT36D

Model # KHDOV30D

Model # KHDOV36D

Model # KHDCOG30DY

Model # KHDCOG36DY

Summary of content (2 pages)

PAGE 1
Item # Item # Item # Item # Item # Item # 1002 835 295 1002 835 317 1002 835 320 1002 835 323 1002 814 804 1002 814 817 Model # KHWHT30D Model # KHWHT36D Model # KHDOV30D Model # KHDOV36D Model # KHDCOG30DY Model # KHDCOG36DY Use and Care Guide Vanity Combo TOOLS REQUIRED Claw hammer Safety goggles HARDWARE INCLUDED Phillips Screwdriver Caulk/sealant AA - Handle x4 Power drill Measuring tape Wall hardware Keyhole saw BB - Long Screw x4 CC - Medium Screw x2 DD - Short Screw x2 Level Installati
PAGE 2
Installation (continued) 7 RE-INSTALLING THE DRAWER NOTE: Drawer should install smoothly; however, there may be minor resistance when the drawer is approximately half to two-thirds installed. This is normal. A LIATE 3. ELAC A □□ Move the ball bearing cages to the front and push the rear of the glides toward the center of the vanity. □□ Insert the drawer box. □□ Ensure the drawer box glide members slide through the plastic guide at the front of the vanity member on each side. A LIATED 3.