Installation Guide

ManualsBrandsGlacier Bay ManualsBathKinghurst 36 in. W x 21 in. D x 33.5 in. H Vanity Cabinet in White

HOMEDEPOT.COM

Please contact 1-888-774-8062 for further assistance.

AA - Handle BB - Knob

CC - Short

Screw

DD - Long

Screw

KHG30D x 4 KHW30D x 4 KHG30D x 2 KHG30D x 6

KHG36D x 4 KHW36D x 4 KHG36D x 2 KHG36D x 6

KHW30D x 1 KHW30D x 3

KHW36D x 1 KHW36D x 3

Installation

PREPARING FOR INSTALLATION

NOTE: Before installation, make

sure all parts are present. Compare

parts with the Hardware Included list.

If any part is missing or damaged, do

not attempt to install the product.

□ Determine the desired mounting location,

and mark the wall where the unit will be

installed.

NOTE: For secure installation, the

unit must be mounted to at least one

wall stud.

CUTTING THE OPENING FOR

PLUMBING FIXTURES

NOTE: This step applies to vanity

cabinets with full back panels only.

□ Locate and mark plumbing on the back panel.

□ Drill a pilot hole through the back panel.

□ Use a keyhole saw to cut an opening for the

plumbing fixtures.

POSITIONING THE

CABINET

□ Move the cabinet into

place, and use wood

shims to level the

cabinet against the wall.

Use and Care Guide

Vanity Combo

TOOLS REQUIRED

Claw hammer Safety goggles Phillips screwdriver

Power drill

Measuring tape Wall hardware

Caulk/sealant Keyhole saw Level

HARDWARE INCLUDED

INSTALLING THE CABINET

□ For wall stud installation, insert #12 x 3 in. screws with

washers into the stud locations (not included).

□ For drywall installation, drill holes at the appropriate

locations and insert toggle bolts with washers (not included).

□ For concrete wall installation, drill 1/4 in. holes at the

appropriate locations and insert #12 wall anchors, followed

by #12 x 3 in. screws (not included).

Item #0000 000 000

Model #KHW30D

Model #KHW36D

Model #KHG30D

Model #KHG36D

INSTALLING THE HARDWARE

BB BB

□ Attach the handle (AA) and knobs (BB)

to the door on the vanity with short

screws (CC) and to the drawers on the

vanity with long screws (DD).

Summary of content (4 pages)

PAGE 1
Item #0000 000 000 Item #0000 000 000 Item #0000 000 000 Item #0000 000 000 Item #0000 000 000 Model #KHW30D Model #KHW36D Model #KHG30D Model #KHG36D Use and Care Guide Vanity Combo TOOLS REQUIRED Claw hammer Safety goggles Power drill Measuring tape Caulk/sealant Keyhole saw HARDWARE INCLUDED Phillips screwdriver AA - Handle Wall hardware Level BB - Knob CC - Short Screw KHG30D x 4 KHW30D x 4 KHG30D x 2 KHG36D x 4 KHW36D x 4 KHG36D x 2 KHW30D x 1 KHW36D x 1 DD - Long Screw KHG30D x 6 KHG3
PAGE 2
Installation (continued) 6 REMOVING THE DRAWER □□ Press release levers in opposite directions while pulling drawer out of the vanity. Press upward 7 Press downward RE-INSTALLING THE DRAWER NOTE: Drawer should install smoothly; however, there may be minor resistance when the drawer is approximately half to two-thirds installed. This is normal. □□ Move the ball bearing cages to the front and push the rear of the glides toward the center of the vanity. □□ Insert the drawer box.
PAGE 3
Núm. de artículo0000 000 000 Núm. de artículo0000 000 000 Núm. de artículo0000 000 000 Núm. de artículo0000 000 000 Núm. de artículo0000 000 000 Núm. de modeloKHW30D Núm. de modeloKHW36D Núm. de modeloKHG30D Núm.
PAGE 4
Instalación (continuado) 6 EXTRACCIÓN DEL CAJÓN □□ Presiona las palancas de desbloqueo en direcciones opuestas mientras sacas el cajón del gabinete. Presiona hacia arriba 7 Presiona hacia abajo INSTALACIÓN DEL CAJÓN NOTA: El cajón debe instalarse suavemente aunque puede existir una pequeña resistencia cuando la instalación haya llegado aproximadamente a la mitad o a los dos tercios. Esto es normal y el cajón debe ser empujado suavemente hasta llegar adecuadamente a su lugar.