Instructions / Assembly

ManualsBrandsGladiator ManualsGarage Storage48 in. L GearTrack Sports Garage Wall Storage Kit with 3-Hooks and Mesh Basket

Prepare the GearTrack®Channels

IMPORTANT: Use correct screw length for your wall type. See chart

below.

*For bare wood studs and covered walls, use an all-weather flat-head type deck screw.

For concrete block and poured masonry, use a flat-head type masonry screw.

For drywall of a thickness not listed in the chart above, see graphic below.

A. Drywall

B. Wooden stud

C. Flat-head screw in

every slot at every stud

D. 1" (2.54 cm) min. to 1

⁄

" (3.18 cm)

max. if near wiring

⁄

(0.635 cm)

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

Tools and Parts Needed:

•Level

• Tape measure

• Drill

•Saw

• Screws (galvanized or all-weather)

Additional Tools and Parts Needed for

Masonry Block/Poured Concrete Wall Installation:

• Hammer drill

• Caulk gun

•

⁄16" x 1

⁄4" (4.45 cm) Flat-head masonry screws (6 screws per channel)

NOTE: GearTrack® Channels can be cut and drilled with ordinary

woodworking equipment. Additional tools may be needed.

Use Requirements

• Maximum coverage per wall is 33% of the wall surface area.

• Maximum weight limit is 75 lbs (34 kg) per linear ft (30.48 cm).

• GearTrack®Channels can be mounted directly to masonry wall, over

drywall to wooden studs, or to bare wooden studs.

• Intended for use in a garage or basement.

NOTE: Before installing GearTrack®Channels to masonry walls, you

must waterproof the wall to avoid mildew or foundation damage.

Walls that appear dry may actually become damp when enclosed by

paneling. Install the channel in accordance with all local codes and

ordinances.

Channel Spacing

If channels are to be used to support accessory hooks and/or small

item bins, they may be spaced in any way desired. If channels are to be

used to support Gladiator® Wall GearBoxes, they must be installed 18"

(46 cm) apart.

NOTE: Wall GearBox model (GAWGB000LG0) requires the channels to

be spaced 21" (53.34 cm) apart.

• Stud finder

• AC finder

• Square

• Pencil

• Construction adhesive

•

⁄32" Masonry drill bit

18" (46 cm)

W10343308B

Screw Length for Wall Type

Screw

Length*

Masonry

Wall

Bare Wood

Studs

Drywall over Wood Studs

⁄2"

(1.27 cm)

⁄8"

(1.59 cm)

⁄4"

(1.91 cm)

#8 X 1

⁄4" (3.18 cm)

#8 X 2" (5.08 cm)

⁄16" X 1

⁄4" (4.45 cm)

(Screw Not Included)

32" (81.3 CM) AND 48" (121.9 CM)

AND 53.15" (135 CM)

GEARTRACK®CHANNEL

AND END CAP

INSTALLATION INSTRUCTIONS

(for use with Gladiator®GarageWorks products only)

Summary of content (6 pages)

PAGE 1
32" (81.3 CM) AND 48" (121.9 CM) AND 53.15" (135 CM) GEARTRACK® CHANNEL AND END CAP INSTALLATION INSTRUCTIONS (for use with Gladiator® GarageWorks products only) Prepare the GearTrack® Channels Tools and Parts IMPORTANT: Use correct screw length for your wall type. See chart below. Screw Length for Wall Type Screw Length* Masonry Wall Bare Wood Studs Drywall over Wood Studs ⁄2" (1.27 cm) 1 5 ⁄8" (1.59 cm) 3 ⁄4" (1.91 cm) #8 X 11 ⁄4 " (3.18 cm) #8 X 2" (5.08 cm) ⁄16" X 13⁄4" (4.
PAGE 2
Install the GearTrack® Channels Masonry Block/Poured Concrete Wall 1. Use a level to position the GearTrack® Channel at the desired height on the wall. 2. Drill a hole through the GearTrack® Channel and into the wall surface. 3. Secure the GearTrack® Channel to the wall by placing 3⁄16" x 1 3⁄4" (4.45 cm) flat-head masonry screws every 24" (60.96 cm) in every slot. NOTE: Channels cut to shorter than 24" (60.96 cm) long should not be used. 4.
PAGE 3
INSTRUCCIONES DE INSTALACIÓN PARA LOS CANALES DE 32" (81,3 CM) Y 48" (121,9 CM) Y 53,15" (135 CM) Y LAS CUBIERTAS DE LOS EXTREMOS DE LA MARCA GEARTRACK® ( Para usarse solamente con los productos Gladiator® GarageWorks) Preparación de los canales GearTrack® IMPORTANTE: Use el tornillo con el largo correcto para el tipo de pared. Vea el cuadro a continuación.
PAGE 4
Instale los canales GearTrack® Pared de bloque de albañilería/concreto vaciado 1. Use un nivel para colocar el canal GearTrack® en la pared, a la altura deseada. 2. Taladre un orificio a través del canal GearTrack® y dentro de la superficie de la pared. 3. Asegure el canal GearTrack® a la pared colocando tornillos de albañilería de cabeza plana de 3⁄16" x 1 3⁄4" (4,45 cm) por cada 24" (60,96 cm) en cada ranura. NOTA: No deben usarse canales cortados a menos de 24" (60,96 cm) de largo. 4.
PAGE 5
INSTRUCTIONS D’INSTALLATION DES PROFILÉS DE 32" (81,3 CM) ET DE 48" (121,9 CM) ET DE 53,15" (135 CM) ET DE L’EMBOUT GEARTRACK® (Pour utilisation avec les produits Gladiator® Garageworks uniquement) Préparation des profilés GearTrack® Outillage et pièces IMPORTANT : Utiliser la longueur de vis adaptée au type de mur. Voir le tableau ci-dessous.
PAGE 6
Espacement des profilés Si les profilés sont destinés à supporter des crochets porte-outils et/ou des casiers permettant de ranger de petits objets, ils peuvent être espacés comme on le désire. Si les profilés sont destinés à soutenir des boîtes à outils murales Gladiator® GearBoxes, l’espacement entre les profilés doit être de 18" (46 cm). 18" (46 cm) REMARQUE : Pour l'utilisation avec le produit mural GearBox (GAWGBOOOLG00), l'espacement entre les profilés devra être de 21" (53,34 cm).