Installation

ManualsBrandsGlasscrafters ManualsPlumbingAcero Collection AT-60T-38-IBK 60" x 66" Frameless Sliding Tub Door with 0.38" Standard Clear Tempered Glass in Iron Black

ACERO Frameless Shower/Tub Enclosure

Installation Instructions

The following instruction sheet is for the installation of the models:

SHOWER ENCLOSURES: AS-60T-38

57”- 60”w X 76”h , AS-54T-38 51”- 54’w X 76”h, AS-48T-38 45”- 48”w X 76”h

TUB ENCLOSURES: AT-66T-38 63”- 66”w X 66”h , AT-60T-38 57”- 60”w X 66”h

All Units are available in four ﬁnishes: Brushed Stainless Steel (BSS), Polished Stainless Steel (PSS), Iron Black (IBK) or Oil Rubbed Bronze (ORB)

GLASSCRAFTERS, INC

193 Veterans Blvd., Carlstadt, NJ 07072

Please use extreme care while unpacking and handling your GlassCrafters’ Shower or Tub Enclosure. If you need

replacement parts or have installation questions and to report any damage contact our GlassCrafters’ customer service

team at 888-683-1362, Monday thru Friday from 8:00 am to 5:00 pm (EST).

Installation shall be made according to manufacturer instructions and drawing.

Glasscrafters recommends the installation be performed by a trained installer.

Revised 4/2019

WARNING: TO INSTALL ON CAST IRON, FIBERGLASS, ACRYLIC OR RESIN TUB OR SHOWER BASE

Check with the tub or shower base manufacturer to determine the tooling required.

Shower Enclosure

Tub Enclosure

INSTALLING

THESE UNITS

REQUIRES

2 PERSONS

FOR BEST RESULTS

Glasscrafters recommends the installation

be performed by a trained installer.

SAVE THESE INSTRUCTIONS

FOR FUTURE REFERENCE

1+(888) 683-1362 -- (Fax) 201-525-1117

sales@glasscraftersinc.com

Summary of content (16 pages)

PAGE 1
GLASSCRAFTERS, INC 193 Veterans Blvd., Carlstadt, NJ 07072 1+(888) 683-1362 -- (Fax) 201-525-1117 sales@glasscraftersinc.
PAGE 2
CAUTION: Risk of injury or product damage. Do not attempt to cut tempered glass. IMPORTANT! Children should be supervised at all times while in Tub/Shower Enclosure. IMPORTANT! Never use Door Handle or Towel Bar to support yourself. This is for towels or wash cloths only. PLEASE STOP THE INSTALLATION AND CONFIRM WITH FACTORY IF THE ACTUAL NUMBER OR TYPE OF PARTS IS DIFFERENT Parts Description ITEM NO. 1 2 3. 4. 6. 7. 8. 9. DESCRIPTION QTY. Vertical Wall Jamb ....................1 Fixed Glass Panel ...
PAGE 3
IMPORTANT: Read all instructions carefully and become familiar with all parts before installation. Unpacking: • • • • • • A box cutter should not be use to open any box. Please remove all staples from the box prior to unpacking metal and glass. Stand Panels upright on a cushioned base, such as a piece of carpet or towel. Do not remove corner protectors during staging of installation. Never place glass directly on hard surfaces. Any assembly that requires the panel to lay ﬂat must be on a cushion surface.
PAGE 4
Installation Overview -Showing steps for installation. Refer to pages 6-15 for step-by-step installation descriptions.
PAGE 5
Preliminary Steps: Inspect the complete product when opening the box to ensure that all parts are accounted for, intact and void of any damage from shipping. Detail Door Assembly STEP A -- Assemble the Door: a) Stand the Glass door upright on a carpet or tarp cushion to protect the glass. Position with the inside of the door facing out. Have the second installer support the door during installation of these parts.
PAGE 6
WARNING: TO INSTALL ON A CAST IRON, FIBERGLASS, GLASS TILE, ACRYLIC OR RESIN TUB OR SHOWER BASE Check with the tub or shower base manufacturer to determine the tooling required. Detail 1C Using the penciled centerline on the wall use a level to recheck the exact vertical position. Mark the top height for the unit at 66” or 76”. Mark for the ﬁnished height of enclosure STEP 1. Determine the Plumb Condition of the opening: Use a level to determined that the enclosure is plumb on both sides.
PAGE 7
DETAIL #2 STEP 2 -- Install the Bottom “U” Channel and Center Guide: a) Using the centerline on the base as a guide, place the Bottom “U” Channel on the base on the outside of the centerline. The end of the U Channel should touch the wall marked for the wall channel l The plumb line mark on the wall opposite the shower head will be the guide for the wall channel. b) Align the outside edge of the Center Guide to butt against and align with the Bottom “U” Channel.
PAGE 8
STEP 4 -- Assemble the Horizontal Rail on the Fixed Panel for position: a) The Panel Screws are shipped in position on the Horizontal Rail. Unscrew to assemble the Horizontal Rail on inside of the ﬁxed glass panel. (See Details 4a & 4b). DETAIL #4a-- Horizontal Rail installed on the Fixed Panel (As viewed from the inside) Attach the Horizontal Rail to the Fixed Panel on the inside face using the two Panel Screw Assembly sets supplied pre-installed on the Horizontal Rail.
PAGE 9
STEP 6 -- Installation of the Horizontal Rail Wall Mounting Brackets: Check for level and Plumb position. a) Using a pencil, mark the outline of both the left and right Horizontal Rail Mounting Wall Brackets.b) Remove the assembled Fixed Panel with the Horizontal Rail and lean against a wall outside of the enclosure. Stand the glass on a carpet or padding to protect the glass. c) Loosed the set screw on the top and remove the Mounting Brackets from the Horizontal Rail.
PAGE 10
STEP 7 -- Install the Door from the Inside of the Unit: Two persons should be used to lift the Door onto the Horizontal Rail. The bottom of the door goes in the Plastic Insert in the Center Guide. Install the Anti-Lift Standoﬀ Assemblies in the pre-drilled holes in the door below the Horizontal Rail. The Anti-Lift Standoﬀ threaded knob inserts from the inside. Be sure to use the gaskets between the knobs and the glass as well as the plastic bushing within the hole to protect the glass.
PAGE 11
STEP 8 -- Install the End Cap and the Curb Dam: a) To Install the End Cap ﬁrst put a bead of Silicon Sealant inside the base of the end of the U Channel. Add sealant to the inside face of the vertical part of the End Cap. Slide the End Cap into the U Channel and press ﬁrmly into place. DETAIL #8a b) Place the Curb Dam into position in front of the U channel to butting the wall. Mark the Curb Dam to ﬁt and cut to size with a stainless steel hacksaw.
PAGE 12
STEP 9 -- Install the Clear “H” vinyl: To install the “H” Clear Vinyl on the Door from the inside. Begin at the bottom edge with the ﬂange pointing to the space between the Door and the Fixed Panel. Press or tap into place with a Rubber Mallet. Trim with cutting pliers to ﬁt just below the Horizontal Rail.
PAGE 13
STEP 10 -- Adjust Roller Height: Remove the Threaded Knob covering the Roller mechanism on the inside of the unit. Using the 2mm Hex Wrench in the Hex Slot position on either side of the Spacer hold the assembly in position while loosening the locking nut as shown below with the 4mm Hex Wrench. Using the 2mm Hex wrench turn the Roller on the Axel to lift and adjust the door for level. Hold in place and tighten the Locking Nut. Remove the Hex Wrenchs and replace the Threaded Knob.
PAGE 14
STEP 11 -- Install the Handle: Insert the inside portion of the Handle (the part with the tapered knob) through the glass into the outer handle. Use vinyl gaskets and bushings to protect the glass. Us the proper Hex “L” wrench to tighten the set screws in the outer Handle to ﬁx the Handle to the Door. DETAIL 11 -- Installing the Handle (As viewed from the inside) Outside Enclosure Inside Enclosure DETAIL 11b (Handle Shown from Below. The set Screw is on the outside.
PAGE 15
STEP12 -- Seal from the inside with Silicone: Apply Silicone Sealant along the inside face of the Vertical Wall Jamb, Bottom “U” Channel, Curb Dam and the seam between the Cover Plate and the U Channel as per the drawing and details #12. (No sealant is required on the Center Guide.) Let cure for 24 hours before use. DETAIL #12 -- Caulking Top view Splash Guard Plastic Insert End Cap DETAIL #12a -Sealing the Wall Jamb and Curb Dam Silicone Sealant is shown here as applied to the INSIDE of the unit.
PAGE 16
Acero Series Models Catalog Number Shower Enclosures AS-60T-38 AS-60T-38 AS-60T-38 AS-60T-38 AS-54T-38 AS-54T-38 AS-54T-38 AS-54T-38 AS-48T-38 AS-48T-38 AS-48T-38 AS-48T-38 Tub Enclosures AT-66T-38 AT-66T-38 AT-66T-38 AT-66T-38 AT-60T-38 AT-60T-38 AT-60T-38 AT-60T-38 PSS- Polished Stainless Steel BSS Brushed Stainless Steel IBK Iron Black ORB Oil Rubbed Bronze Metal Finish PSS BSS IBK ORB PSS BSS IBK ORB PSS BSS IBK ORB NOTES: Model Number… ___________________________________ Dealer __________________